G615XLR Marine Monitor Reference Guide Tel 858 456 8550 or 800 967 4287 · Fax 858 454 9224 · www.argonautcomputer.
TABLE OF CONTENTS Mounting, Wiring, Care Pages 1-3 Button Controls Pages 4-9 Technical Support FAQ Page 10 Support, Repair, Service Policy Pages 11-14 Specifications Page 18
Getting Started and Care Your Argonaut G615XLR monitor has been engineered for trouble-free use in the marine environment. Please retain this reference guide for relevant installation, wiring, care information, and operation adjustment (Button Controls). Surface Mounting The G615XLR monitor has been designed for an easy, secure and sealed installation. For surface mount installations, please note the following steps: 1) Locate a suitable installation mounting surface.
Optional RAM Mount Kit The RAM mount kit includes adapter plate, surface base, swivel arm and monitor mounting base plate. Secure square monitor mounting base plate to adapter plate using four stainless steel 10/32 x ½” flat head screws, flat washers and lock nuts provided (Note: RAM logo should be oriented in same direction as RAM decal on adapter plate) .
Wiring NOTE: THE POSITIVE WIRE IS RED AND THE NEGATIVE IS BLACK. The standard cables include VGA, DVI, RCA/S-Video, and DC Power cable. All cables exit the rear of the monitor through a waterproof cable clamp. Note that the input cable ends are not waterproof and should be placed or installed in a dry, protected area. DO NOT PULL CABLES TIGHT IN ORDER TO PREVENT EXCESS STRAIN AND POSSIBLE BREAK IN CABLE CLAMP SEAL.
Button Control Summary 2. Down (Auto) 1. Menu 3. Decrease 1 2 3 4 5 Menu Down (Auto) Decrease Increase Source/Exit 6 Power LED 4. Increase 6. Power LED 5. Source Hotkey/Exit 7. Power Menu Key Down Key (HOT Key: Auto Config.
Power Flashing Amber: Seeking input signal Green: Monitor on with input signal Power On/Off Note: Your Argonaut G615XLR marine monitor has been preset at the factory for optimal viewing either inside or under direct sunshine. For most usage the power button, Dimming control buttons and signal input hotkey are the primary items that may require adjustment.
Composite - Change input signal source to composite video. Exit - Go Exit back to main menu. Picture Brightness - Adjust Brightness of the screen. Contrast - Ratio of luminance between black and white. Adjust distinction. Blacklevel - Adjust black level. Sharpness - Adjust Sharpness of pictures.
Hue (video only) - Adjust between green tone and purple tone. Saturation (video only) - Adjust color intensity. Exit - Go back to main menu. Color Temperature Choice of: User, Warm, Normal, and Cool – RGB can be adjusted. User: Able to adjust the color by controlling Red, Green, and Blue.
Warm: Red-tinged screen. Normal: Green-tinged screen. Cool: Blue-tinged screen. Auto Color (A-RGB Only) - Color automatically set for input signal. Exit - Go back to main menu. Image Control Available Mode – Analog RGB Auto - Auto configuration of geometry.
Width - Adjust horizontal size of the screen by increasing or decreasing the number of picture elements. Phase - Adjust Phase of screen. Used when noise or overlapped lines are shown on the screen. H Position - Move screen horizontally. V Position – Move screen vertically. Exit - Go back to main menu. Tool OSD Control Time Out: The range of controlling the duration time of the OSD menu (OSD turn-off time).
H Position: Adjust horizontal position of OSD Menu by value. V Position: Adjust vertical position of OSD Menu by value. Reset - Initial set-up, preset by the factory before forwarding. Reset Color - Initial color. Reset Position (A RGB Only) - Initial position. Exit - Go back to main menu.
are bent or corroded. Screen image is not centered or sized properly. * Press Reset Position in OSD. Picture has color defects (white does not look white) Horizontal or vertical disturbances on the screen Image is dim * Press Reset Color in OSD. Monitor Turns Off * Confirm minimum voltage to regulator. * Press Reset in OSD. * Adjust brightness control. ARGONAUT G615XLR TWO YEAR PARTS AND LABOR WARRANTY This warranty covers the Argonaut Computer G615XLR marine display.
Out of Warranty Repair Procedure If it is determined that the failed part is not covered by Argonaut Computer, or is out of warranty, Argonaut Computer will assess the standard parts cost and a repair rate that is authorized by the customer or return the product without repair upon request. Freight All products sent to Argonaut Computer for warranty repair must be shipped to our service center freight prepaid.
OF SUCH DAMAGES. ALL IMPLIED WARRANTIES WITH RESPECT TO ANY OF THE ENCLOSED, INCLUDING WITHOUT LIMITATION, WARRANTIES OR MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NONINFRINGEMENT, ARE LIMITED IN DURATION Customer Support & Repair Service Policy Every Argonaut product comes with support and repair service features. Argonaut Computer, Inc. has designed a Customer Support and Repair Services Policy to provide these services to its valued customers.
To request repair services on your Argonaut product within the warranty period, customer must contact Technical Support to determine the nature of the problem and relevant coverage. In the event customer's Argonaut product needs service, a Return Material Authorization (RMA) number will be assigned and instructions for shipment to our Service Center will be provided. Please note all RMA shipments to our Service Center must be prepaid.
past the 10-day period. Shipping charges are not refundable. A restocking fee of up to 15% of your original purchase value may be charged for testing, reinstallation of operating system/drivers, and packaging replacement. Customer may not return any preinstalled, open-packaged, or customer- registered marine and/or other software, and will be charged current retail list pricing.
Rugged Features Enclosure/Finish Shock/Vibration Mount LCD Connectors Aluminum/Gray Powder Coated All Internal Components, LCD Mil-Spec Shock Mounted Optically Bonded Antireflective Glass, Optional Touch Screen Stainless Steel, Sealed Connector Cable Clamp General Features Display Type TFT Active Matrix Tflex™ LCD; VIS: 15” (38.
