INSTALLATION INSTRUCTIONS - Split system air conditioner - DECLARATION OF CONFORMITY EG This product is marked as it satisfies Directives: – Low voltage no. 2006/95/CE. (Standard: EN60335-2-40:2003 (incl. Corr.:2006) + A11:2004 + A12:2005 + A13:2012 + A1:2006 + A2:2009 con EN 60335-1:2002 + A11:2004 + A1:2004 + A12:2006 + A2:2006 + A13:2008 + A14:2010 + A15:2011). – Electromagnetic compatibility no. 2004/108/CE, 92/31 EEC and 93/68 EEC.
• Ground the unit following local electrical codes. • The Yellow/Green wire cannot be used for any connection different from the ground connection. • Connect all wiring tightly. Loose wiring may cause overheating at connection points and a possible fire hazard. • Do not allow wiring to touch the refrigerant tubing, compressor, or any moving parts of the fan. • Do not use multi-core cable when wiring the power supply and control lines. Use separate cables for each type of line.
Installation site selection - Indoor unit AVOID • Direct sunlight. • Nearby heat sources that may affect unit performance. • Areas where leakage of flammable gas may be expected. • Locations where large amounts of oil mist may occur (such as in kitchen or near factory equipment) because oil contamination can cause operation problems and may deform plastic surfaces and parts of the unit. • Unsteady locations that will cause noise or possible water leakage.
ISTRUZIONI DI INSTALLAZIONE - Condizionatore d’aria Split System - DICHIARAZIONE DI CONFORMITÀ Questo prodotto è marcato in quanto conforme alle Direttive: – Bassa Tensione n. 2006/95/CE (Standard: EN60335-2-40:2003 (incl. Corr.:2006) + A11:2004 + A12:2005 + A13:2012 + A1:2006 + A2:2009 with EN 60335-1:2002 + A11:2004 + A1:2004 + A12:2006 + A2:2006 + A13:2008 + A14:2010 + A15:2011). – Compatibilità Elettromagnetica n. 2004/108/CE, 92/31 CEE e 93/68 CEE.
IMPORTANTE! Leggere prima di iniziare l’installazione • Eseguire la messa a terra dell’unità secondo le norme elettriche locali. • Il conduttore giallo/verde non può essere utilizzato per collegamenti diversi dalla messa a terra. • Fissare bene i cavi. Collegamenti inadeguati possono causare surriscaldamento e un possibile incendio. • I cavi elettrici non devono venire a contatto con i tubi refrigeranti, il compressore o le parti mobili del ventilatore.
Scelta del luogo di installazione unità interna EVITARE • L’esposizione diretta al sole. • La vicinanza a fonti di calore che possono danneggiare la struttura dell’unità. • La presenza di perdite di gas. • La presenza di vapori d’olio (come in una cucina o vicino a macchinari industriali) perché la contaminazione d’olio può provocare malfunzionamento e può deformare superfici e particolari in plastica dell’unità.
NOTICE D’INSTALLATION - Climatiseur split - DECLARATION DE CONFORMITÉ Ce produit est marqué puisque il est conforme aux Directives: – Basse Tension n° 2006/95/CE. (Standard: EN60335-2-40:2003 (incl. Corr.:2006) + A11:2004 + A12:2005 + A13:2012 + A1:2006 + A2:2009 with EN 60335-1:2002 + A11:2004 + A1:2004 + A12:2006 + A2:2006 + A13:2008 + A14:2010 + A15:2011). – Compatibilité Electromagnétique n° 89/336 CEE, 92/31 CEE et 93/68 CEE.
• Effectuez la mise à la terre de l'appareil en respectant les réglementations électriques locales. • Le câble jaune/vert ne peut en aucun cas être utilisé pour toute autre connexion que celle de la mise à la terre. • Serrez fermement toutes les connexions. Un câble mal fixé peut entraîner une surchauffe au point de connexion et présenter un danger potentiel d'incendie. • Il ne faut en aucun cas laisser les câbles toucher la tuyauterie du réfrigérant, le compresseur ou toute pièce mobile.
RECHERCHEZ • Un emplacement approprié à partir duquel l'ensemble de la pièce peut être climatisé de manière uniforme. • Un emplacement suffisamment solide pour supporter le poids de l'appareil. • L’emplacement pour que la distance entre les deux appareils soit la plus courte possible. • Un espace suffisant pour permettre aussi bien un bon fonctionnement qu'une maintenance aisée, ainsi qu'une circulation d'air libre autour de l'appareil.
INSTALLATIONSANLEITUNGEN - Zweirohrsystem-Klimaanlage - KONFORMITÄTSERKLÄRUNG Dieses Produkt ist mit -Zeichen gekennzeichnet, weil es den folgenden Richtlinien entspricht: – Niederspannungsrichtilinie 2006/95/CE. (Standard: EN60335-2-40:2003 (incl. Corr.:2006) + A11:2004 + A12:2005 + A13:2012 + A1:2006 + A2:2009 with EN 60335-1:2002 + A11:2004 + A1:2004 + A12:2006 + A2:2006 + A13:2008 + A14:2010 + A15:2011). – Elektromagnetische Verträglichkeit 2004/108/CE, 92/31 EWG und 93/68 EWG.
WICHTIG! Bitte vor Arbeitsbeginn lesen Tod verursachen. • Erden Sie das Gerät gemäß den örtlich zutreffenden Vorschriften. • Das Gelbe/Grüne Kabel ist für die ausschließliche Verwendung als Erdleitung. • Verbinden Sie Kabel fest miteinander. Lockere Verbindungen können Überhitzung an den Verbindungspunkten erzeugen und ein mögliches Feuerrisiko bedeuten. • Stellen Sie sicher, daß die Verdrahtung nicht die Kühlmittelrohre, den Kompressor oder die beweglichen Teile des Ventilators berührt.
Wahl des Installationsortes - Innenraumgerät VERMEIDEN SIE • Direkte Sonneneinstrahlung. • Wärmequellen in der Nähe des Gerätes, die dessen Leistungsfähigkeit beeinflussen könnten. • Bereiche, wo Leckgasen erwartet werden können. • Die Installationen an Stellen, an denen die Geräte starkem Öldunst ausgesetzt sind (wie z.B. in Küchen oder in der Nähe von Fabrikmaschinen). Ölverschmutung kann zu Betriebstörungen und zur Verformung von Plastikoberflächen und -teilen des Gerätes führen.
INSTRUCCIONES DE INSTALACION - Acondicionador de aire Split System - DECLARACION DE CONFORMIDAD Este Producto está marcado porque responde a las Directivas: – Baja Tensión n° 2006/95/CE. (Standard: EN60335-2-40:2003 (incl. Corr.:2006) + A11:2004 + A12:2005 + A13:2012 + A1:2006 + A2:2009 with EN 60335-1:2002 + A11:2004 + A1:2004 + A12:2006 + A2:2006 + A13:2008 + A14:2010 + A15:2011). – Compatibilidad Electromagnetica n° 2004/108/CE, 92/31 CEE y 93/68 CEE.
¡IMPORTANTE! Leer antes de empezar la instalación • Realizar la puesta a tierra de la unidad siguiendo las normas eléctricas locales. • El conductor amarillo/verde no se puede utilizar para conexiones que no sean la de tierra. • Fijar bien los cables. Un error en las uniones puede provocar recalentamiento o un posible incendio. • No deje que ninguna conexión contacte con el tubo de refrigerante, compresor o parte móviles del ventilador.
Dónde instalar la unidad interior EVITAR • La exposición directa al sol. • Zonas expuestas a fuentes de calor que puedan dañar la estructura de la unidad. • Pérdidas de gas. • Vapores de aceite (como en una cocina o cerca de máquinas industriales), ya que el contacto con el aceite puede provocar mal funcionamiento y puede deformar las superficies de plástico de la unidad. • Lugares donde el punto de apoyo no sea completamente estable, ya que pueden provocar vibraciones, ruidos y posibles pérdidas de agua.
INSTRUÇÕES DE INSTALAÇÃO - Sistema de ar condicionado de Unidades Separadas - DECLARAÇÃO DE CONFORMIDADE Este produto tem a marca porque responde às Directrizes: – Baixa tensão N° 2006/95/CE. (Standard: EN60335-2-40:2003 (incl. Corr.:2006) + A11:2004 + A12:2005 + A13:2012 + A1:2006 + A2:2009 with EN 60335-1:2002 + A11:2004 + A1:2004 + A12:2006 + A2:2006 + A13:2008 + A14:2010 + A15:2011). – Compatibilidade eletromagnética n° 2004/108/CE, 92/31/CEE e 93/68/CEE.
IMPORTANTE ! Queira ler antes de colocar a unidade em funcionamento Este sistema de ar condicionado satisfaz padrões rigorosos sobre segurança e funcionamento. Na sua capacidade de instalador ou encarregado do serviço, é parte importante do seu trabalho instalar ou prestar serviço ao sistema de forma que este funcione segura e eficazmente. Para instalação e funcionamento sem problemas, devese: • Ler cuidadosamente este manual de instruções antes de começar.
• Selecionar uma posição apropriada a partir da qual todos os cantos da sala possam ser uniformemente arrefecidos. • Escolher um local onde o piso seja suficientemente forte para poder suportar o peso da unidade. • Escolher uma posição na qual a distância entre as duas unidades seja a mínima possível. • Escolher a posição mais apropriada para garantir seja uma boa ventilação que espaço suficiente para a manutenção da unidade.
ODHGIES TOPOQETHSHS v ene" monad v e" klimatismouv - Diairoum DHAWSH SUMMORFWSHS To proi>ovn autov fevrei to shvma diovti antapokrivnetai sti" apaithvsei" twn akovlouqwn odhgiwvn: - Camhlhv tavsh ariq. 2006/95/CE. (Standard: EN60335-2-40:2003 (incl. Corr.:2006) + A11:2004 + A12:2005 + A13:2012 + A1:2006 + A2:2009 with EN 60335-1:2002 + A11:2004 + A1:2004 + A12:2006 + A2:2006 + A13:2008 + A14:2010 + A15:2011). - Hlektromagnhtikhv sumbatikovthta ariq. 89/336 EOK, 92/31 EOK kai 93/36 EOK.
SHMANTIKO ! Diabas v te prin arcis v ete thn egkatas v tash v te to susv thma sumv fwna me tou" iscuov nte" topikouv" • Geiws hlektrikouv" ksnonismouvs. • To kivtrino É pravsino kalwvdio den mporeiv na crhsimopoihqeiv gia avlle" sundevsei" parav movno gia geivwsh. • Staqeropoihvste kalav ta kalwvdia. Aneparkeiv" sundevsei" mporeiv na prokalevsoun uperqevrmansh kai purkagiav.
Epiloghv tou cwr v ou egkatas v tash" th" eswterikh"v monad v a" APOFEUGETE • Thn avmesh evkqesh ston hvlio • Oi phgev" qermovthto" mporeiv na kavnoun zhmiav sthn kataskeuhv th" monavda" • Thn topoqevthsh se cwvro me diarroev" aerivou • Thn topoqevthsh se cwvrou" me atmouv" ladiouv ovpw" sthn kouzivna hv kontav se biomhcanikav mhcanhvmata) giativ to lavdi mporeiv na prokalevsei dusleitourgiva kai na paramorfwvsei epifavneie" kai plastikav mikroexarthvmata th" monavda".
INDOOR UNIT • UNITÁ INTERNA • UNITE INTERIEURE • INNENEINHEIT • UNIDAD INTERIOR • UNIDADE INTERIORE • ESWTERIKH MONADA A 250 250 2000 EG Minimum operation and maintenance area. I Area minima di esercizio e manutenzione. F Surface minimum de fonctionnement et d’entretien. D Raumbedarf des Gerätes. E Area mínima de funcionamiento y manutención. P Área mínima para o funcionamento e manutenção. GR Elavcisto" cwvro" leitourgiva" kai sunthvrhsh".
D E EG Before installing the unit it is necessary to remove the front panel: - Open the air intake grille and remove it (detach the safety string). - Remove the front panel by loosening the 4 fixing screws. I Prima di installare l’unità è necessario rimuovere il pannello frontale: - Aprire la griglia di aspirazione e rimuoverla (staccare la funicella di sicurezza). - Rimuovere il pannello frontale togliendo le 4 viti di fissaggio .
F EG Wall installation. Place the bracket to the wall and fix the central screw, level it and mark the other holes to drill as shown in the figure (2 holes are optional); fix completely the bracket. Hang the unit to the bracket, mark the holes to drill for the fixing of the unit. I Installazione a parete. Posizionare la staffa al muro e fissare la vite centrale, metterla a livello ed evidenziare i restanti fori da eseguire, indicati in figura (2 fori sono opzionali); fissare completamente la staffa.
I EG Make the holes for the fixing of the unit. Running power electric cable (with a ground wire) between the two units (see the table of wire section). Check if the quantity and the rawl plugs type supplied are the proper ones for fixing the unit on the wall. I Eseguire i fori per il fissaggio dell’unità. Stendere il cavo elettrico di collegamento (con filo di terra) tra le due unità (vedere tabella per la sezione dei fili).
L M EG Remove the electrical box cover to operate on the terminal strip. I Rimuovere il coperchio scatola componenti elettrici per accedere alla morsettiera. F Enlever le capot de la boîte des composants électriques. D Die Abdeckplatte des Klammbrettes entfernen. E Quitar la tapa de la caja de los componentes eléctricos para acceder a la regleta de bornes. P Remova o painel de acesso dos componentes elétricos para ter acesso aos terminas.
E Colocar el cable eléctrico y concitarlo al tablero de bornes (véase esquema de conexiones). Bloquear el cable a la abrazadera de la brida. ADVERTÊNCIA Controlar que los bornes de los cables estér bien sujetos en el tablero de bornes. De otro modo, podrían recalentarlo o provocar problemas en el funcionamiento del acondicionador con riesgo le incendio. Al cerrar la caja de los componentes électricos, controlar que los cables no sobresalgar y que no se queden atrapados entre la tapa y la unidad.
O EG Fill the tank and verify that the condensate can flow correctly. Reassemble the front panel. I Riempire la vaschetta quindi verificare il corretto scarico della condensa e rimontare il pannello frontale. F Remplir le bac et vérifier que la sortie des condensat soit correcte. Remonter le panneau frontal. D Den Tank füllen und den korrekten Kondenswasser-Auslaß überprüfen. Das Vorpaneel wiederzusammensetzen. E Llenar la tanque y controlar que el líquido de condensación se desagüe correctamente.
SYSTEM WIRING DIAGRAM • COLLEGAMENTI ELETTRICI DEL SISTEMA • BRANCHEMENTS ELECTRIQUES DU SYSTEME • ELEKTRISCHE ANSCHLÜSSE DES SYSTEMS • CONEXIONES ELECTRICAS DEL SISTEMA • SISTEMA DE INSTALAÇÃO ELÉTRICA • HLEKTRIKH SUNDESH TOU SUSTHMATOS LENGTH, SIZE WIRES AND DELAYED FUSE • LUNGHEZZA, SEZIONE CAVI E FUSIBILI RITARDATI • LONGUEUR, SECTION CABLES ET FUSIBLES RETARDES • KABEL-LÄNGE UND QUERSCHNITT UND TRÄGE SICHERUNGEN • LONGITUD, SECCION DE CABLES Y FUSIBLES DE ACCION RETARDADA • COMPRIMENTO, SECÇÃO DO FIO
D Verbindungskabel B (ABGESCHIRMT): Elektrisches zweipoliges Abschirmkabel; Querschnitt und Länge des Kabels sind in der Installationsanleitungen der Ausseneinheit angezeigt. Das Kabel soll nicht leichter als H05VVC4V5-K-Typ sein (gemäß CEI 20-20 CENELEC HD21). Verbindungskabel C (mit Erdungsleitung): Elektrisches mehradriges Kabel; Querschnitt und Länge des Kabels sind in der Installationsanleitungen der Ausseneinheit angezeigt.
REMOTE CONTROL UNIT INSTALLATION • POSIZIONE DI INSTALLAZIONE TELECOMANDO • EMPLACEMENT DE LA COMMANDE A DISTANCE • POSITION DER FERNBEDIENUNG • POSICION DE INSTALACION DEL MANDO A DISTANCIA • POSIÇÃO DA INSTALAÇÃO DA UNIDADE DE CONTROLE REMOTO • QESH TOPOQETHSHS THLECEIRISTHRIOU EG I F D E P GR REMOTE CONTROL UNIT INSTALLATION To ensure that the air conditioner operates correctly, DO NOT install the remote control unit in the following places: • In direct sunlight.
EG WALL-MOUNTED POSITION • Momentarily place the remote control unit in the desired mounting position. • Verify that the remote control unit can operate from this position. • Fix the support at the wall with two screws and hang the remote control unit. I POSIZIONE A PARETE • Momentaneamente sistemare il telecomando nella posizione desiderata. • Verificare che da questa posizione prescelta il telecomando dialoghi con il condizionatore. • Fissare il supporto al muro con due viti e appendere il telecomando.
DEFAULT SETTING RESET - RESET IMPOSTAZIONI DI DEFAULT - REMISE A ZERO DES REGLAGES DE DEFAUT - ZURÜCKSETZEN AUF STANDARDEINSTELLUNGEN - RESTABLECER LA CONFIGURACIÓN PREDETERMINADA - RESTABLECIMENTO DAS CONFIGURAÇÕES DE FABRICA - ∂ ·Ó·ÊÔÚ¿ ÛÙ¿ÓÙ·ÚÙ Ú˘ıÌ›ÛÂˆÓ EG To operate the unit again with the default setting it is necessary to set the remote control as follows: C Filter: ON Night Mode / High Power Mode: OFF Operation mode: AUTO Flap: AUTO Set-point: 10°C At this point, press contemporary the FAN and IFE
E Para restablecer las configuraciones predeterminadas de la unidad interior, ustedes tienen que regular el mando a distancia de la manera siguiente: Filter: ON Night Mode / High Power Mode: OFF Modo de funcionamiento: AUTO Flap: AUTO Temperatura seleccionada: 10°C Ahora, presionar simultáneamente los pulsadores del mando a distancia “FAN” y “I FEEL” durante mas de 5 segundos y soltarlos dirigiendo el mando a distancia hacia la unidad interior.
PUMP DOWN (See Installation Instruction of Outdoor Unit) EG Pump down means collecting all refrigerant gas in the system back into the outdoor unit without losing gas. Pump down is used when the unit is to be moved of before servicing the refrigerant circuit. I F D E Pump down significa recuperare tutto il gas refrigerante nell’Unità Esterna senza perdere la carica del sistema. Serve quando si deve riposizionare il condizionatore e per interventi di riparazione sul circuito frigorifero.
OUTDOOR/INDOOR UNIT REFRIGERANT CIRCUIT ADDRESS EG Indoor units that are part of a multisplit system must be properly configured to be able to communicate with the outdoor unit over different channels (Indoor A, Indoor B, etc...) of the communication bus. Each indoor unit address must correspond to the physical connection of the indoor unit to the outdoor unit refrigerant circuit, i.e.: Refrigerant Circuit A <--> Indoor Unit Address A Refrigerant Circuit B <--> Indoor Unit Address B ...
(2) ADDRESS SETTING THROUGH REMOTE CONTROLLER (UP TO 8 INDOOR UNITS) Set the remote controller as shown in the table.
(3) AUTOMATIC ADDRESSING PROCEDURE System requirements: Outdoor unit must have a recent firmware version that supports the automatic addressing procedure. Indoor units must have a recent firmware version that supports the automatic addressing procedure Dip-switch for communication address setting on the indoor unit (SW2) must be left to the factory default state, i.e. to the OFF position. EG Activation of automatic addressing procedure Power on the whole system.
INDIRIZZO CIRCUITO REFRIGERANTE UNITA’ ESTERNA/INTERNA Le unità interne che fanno parte di un sistema multisplit devono essere opportunamente collegate in modo da comunicare con l’unità esterna su diversi canali (Indoor A, Indoor B, etc...) del bus di comunicazione.
(2) IMPOSTAZIONE INDIRIZZI TRAMITE TELECOMANDO (FINO A 8 UNITA’ INTERNE) Impostare il telecomando come indicato in tabella.
(3) PROCEDURA DI INDIRIZZAMENTO AUTOMATICO Requisiti di sistema: L’unità esterna deve avere una versione firmware recente che supporti la procedura di indirizzamento automatico. Le unità interne devono avere una versione firmware recente che supporti la procedura di indirizzamento automatico. I microinterruttori per l’impostazione dell’indirizzo di comunicazione sull’unità interna (SW2) devono essere lasciati nello stato di fabbrica, cioè in posizione OFF.
ADRESSE DU CIRCUIT DE REFRIGERATION UNITE EXTERIEURE/INTERIEURE FG Les unités intérieures qui font partie d'un système multisplit doivent être configurés correctement pour communiquer avec l'unité extérieure sur plusieurs canaux (unité intérieure A, unité intérieure B, etc ...) du bus de communication. Chaque adresse de l'unité intérieure doit correspondre à la connexion physique de l'unité intérieure avec le circuit réfrigérant de l'unité extérieure, c'est à dire.
(2) REGLAGE DES ADRESSES AVEC LA TELECOMMANDE (JUSQU’A 8 UNITES INTERIEURES) Régler la télécommande comme indiqué dans le tableau.
(3) PROCEDURE D’ADRESSAGE AUTOMATIQUE Exigences du système: L'unité extérieure doit avoir une version récente du firmware qui prend en charge la procédure d'adressage automatique. Les unités intérieures doivent avoir une version récente du firmware qui prend en charge la procédure d'adressage automatique. Les interrupteurs pour le réglage d'adresse de communication sur l'unité intérieure (SW2) doit être laissée à l'état d'usine par défaut, c’est-à-dire la position OFF.
AUSSEN/INNENEINHEIT-KÜHLROHRE ADRESSE Inneneinheiten, die Teil eines Multisplit-System sind, müssen korrekt konfiguriert sein, um mit der Außeneinheit über verschiedene Kanäle des Kommunikationsbusses zu kommunizieren (Inneneinheit A, Inneneinheit B, etc. ...). Jedes Inneneinheit-Adresse muß auf die physikalische Verbindung der Inneneinheit zur Außeneinheit Kältemittelkreislauf entsprechen, d.h.: Kältemittelkreislauf A <--> Inneneinheit-Adresse A Kältemittelkreislauf B <--> Inneneinheit-Adresse B ...
(2) ADRESSEN-EINSTELLUNG MIT DER FERNBEDIENUNG (BIS ZU 8 INNENEINHEITEN) Stellen Sie die Fernbedienung ein, wie in der Tabelle gezeigt ist.
(3) AUTOMATISCHE ADRESSIERUNG System Anforderungen: Die Außeneinheit muß eine aktuelle Firmware-Version haben, die die automatische Adressierung unterstützt. Die Inneneinheiten müssen eine aktuelle Firmware-Version haben, die die automatische Adressierung unterstützen. Die Schalter für die Kommunikation Adresseinstellung auf der Inneneinheit (SW2) müssen auf die Werkseinstellung belassen werden, d.h. in die Position OFF. Aktivierung vom automatischen Adressierung-Verfahren Einschalten das ganze System.
DIRECCION DEL CIRCUITO DE REFRIGERACIÓN UNIDAD EXTERIOR/INTERIOR EG Las unidades interiores que son parte de un sistema multisplit deben estar configurados correctamente para poder comunicar con la unidad exterior a través de diferentes canales (unidad interior A, unidad interior B, etc ...) del bus de comunicación.
(2) REGULACION DE LAS DIRECCIONES CON EL MANDO A DISTANCIA (HASTA 8 UNIDADES INTERIORES) Regular el mando a distancia como indicado en la tabla.
(3) PROCEDIMIENTO DE DIRECCIONAMIENTO AUTOMÁTICO Requisitos del sistema: La unidad exterior debe tener una versión reciente de firmware que soporta el procedimiento de direccionamiento automático. Las unidades interiores deben tener una versión reciente de firmware que soporta el procedimiento de direccionamiento automático. Los interruptores para la configuración de la dirección de comunicación de la unidad interior (SW2) se debe dejar al estado predeterminado de fábrica, es decir, en la posición OFF.
ENDEREÇO DE TUBAGENS DE REFRIGERANTE UNIDADE EXTERIOR/INTERIOR As unidades interiores que são parte de um sistema multi-split devem ser configuradas corretamente para poder comunicar com a unidade exterior através de diferentes canais de comunicação (Unidade interior A Indoor, Unidade interior B, etc ...).
(2) AJUSTAÇÃO DOS ENDEREÇOS COM O CONTROLE REMOTO (ATÉ 8 UNIDADES INTERIORES) Ajustar o controle remoto como mostrado na tabela.
(3) PROCEDIMENTO DE ENDEREÇAMENTO AUTOMÁTICO Requerimentos do sistema: A unidade exterior deve ter uma versão recente do firmware que suporte o procedimento de endereçamento automático. As unidades interiores devem ter uma versão recente do firmware que suporte o procedimento de endereçamento automático. Os interruptores para configuração de endereço de comunicação da unidade interior (SW2) deve ser deixado para o estado padrão de fábrica, ou seja, para a posição OFF.
dieuqunv sewn Exwterike"v monad v e" - Eswterike"v monad v e" √È ÂÛˆÙÂÚÈΤ˜ ÌÔÓ¿‰Â˜ Ô˘ · ÔÙÂÏÔ‡Ó Ì¤ÚÔ˜ ÂÓfi˜ Û˘ÛÙ‹Ì·ÙÔ˜ multisplit ı· Ú¤ ÂÈ Ó· Û˘Ó‰ÂıÔ‡Ó Î·Ù¿ÏÏËÏ· ÒÛÙ ӷ Ì ÔÚÔ‡Ó Ó·  ÈÎÔÈÓˆÓ‹ÛÔ˘Ó Ì ÙËÓ Â͈ÙÂÚÈ΋ ÌÔÓ¿‰· ̤ۈ ‰È·ÊÔÚÂÙÈÎÒÓ Î·Ó·ÏÈÒÓ ( ∂ÛˆÙÂÚÈ΋ ∞, ∂ÛˆÙÂÚÈ΋ μ, ÎÏ ..) ÙÔ˘ ‰È·‡ÏÔ˘  ÈÎÔÈÓˆÓ›·˜.
v " 8 Eswterike"v monad v e") (2) RÁQMISH DIEUQUNSEIS ME THLECEIRISTHRIO (ew ƒ˘ıÌ›ÛÙ ÙÔ ÙËϯÂÈÚÈÛÙ‹ÚÈÔ fi ˆ˜ ·Ó·Ê¤ÚÂÙ·È ÛÙÔÓ ›Ó·Î·.
(3) ∞ÀΔ√ª∞Δ∏ ƒÀ£ªπ™∏ ¢π∂À£À¡™∏™ ∞ ·ÈÙ‹ÛÂȘ Û˘ÛÙ‹Ì·ÙÔ˜: ∏ Â͈ÙÂÚÈ΋ ÌÔÓ¿‰· ı· Ú¤ ÂÈ Ó· ¤¯ÂÈ Ì›· ÚfiÛÊ·ÙË ¤Î‰ÔÛË ˘ÏÈÎÔÏÔÁÈÛÌÈÎÔ‡ Ô˘ Ó· ˘ ÔÛÙËÚ›˙ÂÈ ÙËÓ ‰È·‰Èηۛ· ·˘ÙfiÌ·Ù˘ Ú‡ıÌÈÛ˘ ‰È‡ı˘ÓÛ˘. √È ÂÛˆÙÂÚÈΤ˜ ÌÔÓ¿‰Â˜ ı· Ú¤ ÂÈ Ó· ¤¯Ô˘Ó Ì›· ÚfiÛÊ·ÙË ¤Î‰ÔÛË ˘ÏÈÎÔÏÔÁÈÛÌÈÎÔ‡ Ô˘ Ó· ˘ ÔÛÙËÚ›˙ÂÈ ÙËÓ ‰È·‰Èηۛ· ·˘ÙfiÌ·Ù˘ Ú‡ıÌÈÛ˘ ‰È‡ı˘ÓÛ˘. √ ÌÈÎÚԉȷÎfi Ù˘ ÁÈ· ÙÔÓ ÔÚÈÛÌfi Ù˘ ‰È‡ı˘ÓÛ˘  ÈÎÔÈÓˆÓ›·˜ ÛÙËÓ ÂÛˆÙÂÚÈ΋ ÌÔÓ¿‰· (SW2), ı· Ú¤ ÂÈ Ó· ·Ú·Ì¤ÓÂÈ ÛÙËÓ Î·Ù¿ÛÙ·ÛË ÂÚÁÔÛÙ·ÛÈ·ÎÒÓ Ú˘ı̛ۈÓ, ‰ËÏ·‰‹ ÛÙË ı¤ÛË OFF.
REFRIGERANT CIRCUIT CHECK • CONTROLLO CIRCUITO REFRIGERANTE • CONTROLE DU CIRCUIT DE REFRIGERATION • NACHPRÜFUNG DER KÜHLROHRE • COMPROBACIÓN DEL CIRCUITO DE REFRIGERACIÓN • VERIFICAÇÃO DE TUBAGENS DE REFRIGERANTE • ¢π∞¢π∫∞™π∞ ƒÀ£ªπ™∏™ æÀ∫Δπ∫√À ∫À∫§øª∞Δ√™ EG 1. Power ON the system. 2. Set the remote controller of unit A as following (units B, C and D must be OFF): -Mode: COOLING -Filter: ON -Set-point: 32°C 3.
E 1. Encender el sistema. 2. Regular el mando a distancia de la unidad A como sigue (las unidades B, C y D tienen que ser apagadas): -Modo de funcionamiento: REFRIGERACIÓN -Filtro: ON -Temperatura: 32°C 3. Presionar los pulsadores FAN + IFEEL durante 5 segundos, dirigiendo el mando a distancia directamente al receptor del acondicionador. El sistema funciona durante 3 minutos. Durante este funcionamiento la luz TIMER relampaguea, mientras la luz OPERATION está encendida.
MATCH BETWEEN REMOTE CONTROLLER AND INDOOR UNIT • ABBINAMENTO TRA TELECOMANDO E UNITA’ INTERNA • COMBINAISON ENTRE TELECOMMANDE ET UNITE INTERIEURE • KOMBINATION ZWISCHEN FERNBEDIENUNG UND INNENEINHEIT • COMBINACION ENTRE MANDO A DISTANCIA Y UNIDAD INTERIOR • COMBINAÇÃO ENTRE UNIDADE DE CONTROLE REMOTO E UNIDADE INTERIOR • dieuqunv sewn ÙËϯÂÈÚÈÛÙ‹ÚÈÔ - Eswterike"v monad v e" EG Disconnect the power of indoor unit. Remove the batteries from the remote controller. ● Set the microswitches (see table).
INDOOR UNIT UNITA’ INTERNA UNITE INTERIEURE INNENEINHEIT UNIDAD INTERIOR UNIDADE INTERIOR Eswterike"v monad v e" EG Set SW1 as shown in the table. I Impostare SW1 come indicato in tabella. F Régler SW1 comme indiqué dans le tableau. D Stellen Sie SW1 ein, wie in der Tabelle gezeigt ist. E Regular SW1 como indicado en la tabla. P Ajustar SW1 como mostrado na tabela. GR ƒ˘ıÌ›ÛÙ ÙÔ SW1 fi ˆ˜ ·Ó·Ê¤ÚÂÙ·È ÛÙÔÓ ›Ó·Î·.
REMOTE CONTROLLER: HOW TO CHANGE FROM INFRARED TO WIRED • TELECOMANDO: TRASFORMAZIONE DA INFRAROSSI A FILO • TELECOMMANDE: TRANSFORMATION DE INFRAROUGE A FIL • FERNBEDIENUNG: WANDEL VOM INFRAROT ZU KABEL • MANDO A DISTANCIA: CAMBIO DE INFRARROJOS A CABLE • UNIDADE DE CONTROLE REMOTO: MUDANCA DE INFRAVERMELHO A FIO • THLECEIRISTHRIO : °È· ÙËÓ ÂÓÙÔÏ‹ ª∂ ∫∞§ø¢π√ YEL GRN/YEL BLK VLT GRN EG I PREPARE THE REMOTE CONTROLLER ● Detach the plastic cover of the remote controller terminal block.
F D PREPARATION DE LA TELECOMMANDE ● Retirez le couvercle en plastique de la borne de la télécommande. ● Ouvrez le compartiment des piles, retirer les piles et régler les interrupteurs 5 et 6 en la position OFF. ● Fermez le compartiment des piles sans mettre les piles (la télécommande sera alimentée par le câble). LIAISON Utilisez un câble électrique tripolaire blindé 0,5mm2, longueur max.15m. Le câble doit être de type H05VVC4V5-K minimum (selon CEI 20-20 CENELEC HD21).
P PREPARAÇÃO DO CONTROLO REMOTO ● Remover a tampa de plástico da placa de terminais do controlo remoto. ● Abrir o compartimento das pilhas, remover as pilhas e colocar os microinterruptores 5 e 6 em posição OFF. ● Fechar o compartimento das pilhas sem voltar a colocar as pilhas (o controlo remoto será alimentado por um fio). LIGAÇÃO Utilizar um fio elétrico tripolar blindado 0,5mm2, comprimento máx. 15m. O fio não deve ser mais ligeiro que o tipo H05VVC4V5-K (de acordo com CEI 20-20 CENELEC HD21).
Tel. +39 0331 755111 - Fax +39 0331 776240 www.argoclima.com S.A.C.