Important Notes: Please read all the instructions before contacting customer support. Please contact customer support before returning the product,we will reply the first time. Customer Support: Email: service@ardwolf.com Web site: www.ardwolf.
Content 1. Features ------------------------------------------------------------------3 3 4 2. Specifications ------------------------------------------------------------ 4 Ardwolf A10 Fingerprint Touchscreen Door Lock User Manual 3. How to scan your fingerprint ----------------------------------------- 4 4 4. Flow chart of menu -----------------------------------------------------5 5 5 5. Rule of operation--------------------------------------------------------- 5 5 5 6.
• Double verification mode: unlock by User code + fingerprint or fingerprint + different fingerprint, when you enable this mode. Active sensor area • Support passage mode: stay at “unlock” state during the passage mode. Fingerprint sensor • Memory function: “power run-out” or “system reset” will not cause the loss of enrolled fingerprint(s) and user code(s). Touchscreen • Reversible lever: lock fits both left-handled and right-handed door. • Reversing lever controlled by key.
3. How to scan your fingerprint 4. Flow chart of menu When placing your finger on the fingerprint sensor to scan, make sure that the location of the fingerprint “core” is making direct contact with fingerprint sensor. Apply medium pressure, or just enough to flatten the skin on your finger. Fingerprint User Code System AT logs Fingerprint User Code System AT logs The fingerprint sensor won’t get your fingerprint image if you take the following way. Enroll Fingerpr. Delete Fingerpr.
. Rule of operation 7. Delete Fingerprint Login system, enter menu page (refer page 5 “5. Rule of operation”). Active lock by touching screen then touch #. Login page will show up. Login system by Admin Code or Admin Fingerprint. After login system, following Menu to program fingerprint, user code or set up lock.Default administrator code(1234). Menu Fingerprint User Code 2↑,8↓, # Enter Enroll Fingerpr. Delete Fingerpr.
11. Delete All User Code Login system, enter menu page (refter page 5 “5. Rule of operation”).
15. Check user information Login system, enter menu page (refer page 5 “5. Rule of operation”). You may check user information in the system. Menu User Code System 2↑,8↓, # Enter System Beep About 2↑,8↓, # Enter 18. Audit Trail log Login system, enter menu page (refer page 5 “5. Rule of operation”). You may check audit trail logs on lock directly. Touch “2” or “8” to page up or down Admin Finger Capacity: 5 Admin: 1 2↑, 8↓, * Exit 16.
the lock onto a door, you will need to take the lock off the door in order to locate the reset button. Ardwolf A10 FINGERPRINT KEYPAD LOCK INSTALLATION After resetting the system, Programming Code will revert back to the default programming code INSTRUCTIONS (1234). All user fingerprints and user codes will remain in the system. You may login system to use command to delete all fingerprint or user code when you need it.
4. Prepare doorjamb (see fig. 8). 4.1 Mark centerlines on jamb exactly opposite center of latch hole. 4.2 Make rectangle holes as shown. 4.3 Use strike as a pattern for mortise and pilot holes. Strike should fit flush. Part II.
(A) (B) (C) (D) (E) Key Outside Lever Cylinder Outside chassis Lever Catch (F) (G) (H) (I) (J) Latch Latch/Strike Screws Strike Inside chassis Allen Screw (A) Mounting Screws (B) Inside Lever (M) Cover (N) Cover Screw (O) Allen Wrench The lock comes with two (K) Mounting Screws M5x60 2⅜” (60 mm) long, one (N) M3x25 1”(25 mm) long Cover Screw, one (J) Allen Screw, one (E) Lever Catch and 4 pieces (G) Latch/Strike Screws. Note: The lock fit door thickness between 1⅜” and 2⅜”.
3.4 Insert Cylinder in Lever Spindle. The Cylinder’s tail toward left if you want to set lock as left-handed (see fig. 7b), otherwise the Cylinder’s tail toward right (see fig. 8b). 3.5 Put lever on Lever Spindle (see fig. 7c, 8c). The lever will stop at half way when you push Lever in. Insert key into Cylinder, push the lever (see fig. 9b) and rotate the key CLOCKWISE until the lever is pushed in. Key should be rotated around 90° but could be up to 135° (see fig. 9a).
fig. 12 fig. 13 Installation Option: The lock will stay on vertical position on the door as long as the two mounting screws were tied up in most case. You may put a tapping screw on inside chassis to increase lock stability. 1. Remove two screws in battery compartment. You will see mounting hole under battery compartment. 2. Use 3/8" (8 mm) Drill Bits to drill a hole on door through mounting hole. 3. Put screw pole on front metal plate. 4. Put screw through mounting hole to connect with screw pole. 5.
