Datasheet
Table Of Contents
- 1/3.2-Inch System-On-A-Chip (SOC) CMOS Digital Image Sensor
- Features
- Applications
- Ordering Information
- General Description
- Feature Overview
- Typical Connection
- Ballout and Interface
- Architecture Overview
- Registers and Variables
- Registers
- Registers
- IFP Registers, Page 1
- IFP Registers, Page 2
- JPEG Indirect Registers
- Table 8: JPEG Indirect Registers (See Registers 30 and 31, Page 2)
- Firmware Driver Variables
- Table 9: Drivers IDs
- Table 10: Driver Variables-Monitor Driver (ID = 0)
- Table 11: Driver Variables-Sequencer Driver (ID = 1)
- Table 12: Driver Variables-Auto Exposure Driver (ID = 2)
- Table 13: Driver Variables-Auto White Balance (ID = 3)
- Table 14: Driver Variables-Flicker Detection Driver (ID = 4)
- Table 15: Driver Variables-Auto Focus Driver (ID = 5)
- Table 16: Driver Variables-Auto Focus Mechanics Driver (ID = 6)
- Table 17: Driver Variables-Mode/Context Driver (ID = 7)
- Table 18: Driver Variables-JPEG Driver (ID = 9)
- Table 19: Driver Variables-Histogram Driver (ID = 11)
- MCU Register List and Memory Map
- JPEG Indirect Registers
- Output Format and Timing
- Sensor Core
- Feature Description
- PLL Generated Master Clock
- PLL Setup
- Window Control
- Pixel Border
- Readout Modes
- Figure 20: 6 Pixels in Normal and Column Mirror Readout Modes
- Figure 21: 6 Rows in Normal and Row Mirror Readout Modes
- Table 30: Skip Values
- Figure 22: 8 Pixels in Normal and Column Skip 2x Readout Modes
- Figure 23: 16 Pixels in Normal and Column Skip 4x Readout Modes
- Figure 24: 32 Pixels in Normal and Column Skip 8x Readout Modes
- Figure 25: 64 Pixels in Normal and Column Skip 16x Readout Modes
- Table 31: Row Addressing
- Table 32: Column Addressing
- Frame Rate Control
- Context Switching
- Integration Time
- Flash STROBE
- Global Reset
- Analog Signal Path
- Analog Inputs AIN1-AIN3
- Firmware
- Firmware
- Start-Up and Usage
- General Purpose I/O
- Introduction
- GPIO Output Control Overview
- Waveform Programming
- Notification Signals
- Digital and Analog Inputs
- GPIO Software Drivers
- Auto Focus
- Figure 42: Search for Best Focus
- Figure 43: Scene with Two Potential Focus Targets at Different Distances from Camera
- Figure 44: Dependence of Luminance-Normalized Local Sharpness Scores on Lens Position
- Figure 45: Example of Position Weight Histogram Created by AF Driver
- Figure 46: Auto Focus Windows
- Figure 47: Computation of Sharpness Scores and Luminance Average for an AF Window
- Table 41: Examples of AF Filters that can be Programmed into the MT9D111
- Spectral Characteristics
- Electrical Specifications
- Packaging
- Appendix A: Two-Wire Serial Register Interface
- Protocol
- Sequence
- Bus Idle State
- Start Bit
- Stop Bit
- Slave Address
- Data Bit Transfer
- Acknowledge Bit
- No-Acknowledge Bit
- Page Register
- Sample Write and Read Sequences
- Figure 52: WRITE Timing to R0x09:0-Value 0x0284
- Figure 53: READ Timing from R0x09:0; Returned Value 0x0284
- Figure 54: WRITE Timing to R0x09:0-Value 0x0284
- Figure 55: READ Timing from R0x09:0; Returned Value 0x0284
- Figure 56: Two-Wire Serial Bus Timing Parameters
- Table 46: Two-wire Serial Bus Characteristics
- Revision History
PDF: 09005aef8202ec2e/Source: 09005aef8202ebf7 Micron Technology, Inc., reserves the right to change products or specifications without notice.
MT9D111__5_REV5.fm - Rev. B 2/06 EN
97 ©2004 Micron Technology, Inc. All rights reserved.
MT9D111 - 1/3.2-Inch 2-Megapixel SOC Digital Image Sensor
JPEG Indirect Registers
Micron Confidential and Proprietary
JPEG
Table 18: Driver Variables−JPEG Driver (ID = 9)
Offs Name Type Def RW Description
0 vmt void*
58451 RW Reserved.
2 width uint 1600
R Image width (see mode.output_width).
4 height uint 1200
R Image height (see mode.output_height).
6formatuchar
0 RW Image format:
0
—YCbCr 4:2:2
1
—YCbCr 4:2:0
2—Monochrome
7configuchar
52
RW Configuration and handshaking:
Bit 0
—if 1, video; if 0, still snapshot
Bit 1—enable handshaking with host at every error frame
Bit 2—enable retry after an unsuccessful encode or transfer
Bit 3
—host indicates it is ready for next frame
Bit 4—enable scaled quantization table generation
Bit 5—enable auto-select quantization table
Bit 7:6
—quantization table ID
8 restartInt uint
0 RW Restart marker interval:
0 = restart marker is disabled
10 qscale1 uchar
6RWBit 6:0
—scaling factor for first set of quantization tables
Bit 7—1, new scaling factor value
11 qscale2 uchar
9RWBit 6:0
—scaling factor for second set of quantization tables
Bit 7
—if 1, new scaling factor value
12 qscale3 uchar
12 RW Bit 6:0
—scaling factor for third set of quantization tables
Bit 7—if 1, new scaling factor value
13 timeoutFrames uchar
10 RW Number of frames to time out when host is not responding
(setting bit 3 of config) to an unsuccessful JPEG frame while bit
1 of config is set.
14 state uchar 0
R JPEG driver state.
15 dataLengthMSB uchar
R Bit [23:16] of previous frame JPEG data length.
16 dataLengthLSBs uint
R Bit [15:0] of previous frame JPEG data length.










