User's Manual

Notification of incoming calls
Map Locate
9
Warning
13
Do not disassemble, repair, modify or replace the Charm Tag Unit or any of its components.
Please comply with the national and international flight safety regulations when using device
during your flight trip.
When storing rechargeable batteries for collection, keep in a vented, non-metal container.
Operating for this product is between 40˚F~103˚F (5˚C~40˚C). Storage for this product is
between -4F˚~185˚F(-20˚C~85˚C).
Do NOT dispose of the battery in public trash; it is unlawful under state and federal
environmental laws and regulations.
Please dispose of the battery at local battery recycling center.
a. To set map Location function manually, go to SetView Menu page
and tap the button to go to MapView.(Figure 10)
b. To manually select a Location mark, tap the button and
choose [YES] ,you will see a red mark pin on the current blue
location mark.(Figure 11)
c. Auto set map location function: go to MapView Menu and tap the
button and remove the current mark pin , then enable the
Map Location function. When your iOS Device detects linkLossAlert ,
the iOS Device will automark the Location pin on MapView.(Figure 12)
Please notice map location is at the base of the iOS Device
GPS function if outdoors. If indoor, Please enable Wi-Fi to get
Location accurately.
Please go to SetView Menu to enable the call alert function.
Step: Call Alert Enable
When you get a phone call, the Charm Tag will start beeping and
flashing to remind you.
Troubleshooting
12
If you try to discover a device, but cannot find it, this usually
indicates that there is existing bond information. Locate and
remove(Figure 13) existing bond information from your iOS device
and from Bluetooth Setting to "Forget device". (Figure 15)
May be you need to shut down iOS device to clean holding
information completely.
Removing bond information from iOS
Bond information can be removed from the Settings menu, by going
to General and then Bluetooth. There you should see the name of
the device you want to remove, tap it, and choose "Forget this
device". (Figure 15)
Step :
Removing bond information from device
To remove device permanently:
a.) Disconnection device first and go to SetView page to ”Remove”
(Figure 12) and ”Delete” (Figure 13) Device. Follow “Removing
bond information from the iOS” setps to completely remove
device from the iOS.
Step : YES OK
b.) Remove battery from device and re-install to re-start pairing
process.
What can cause a false Out-of-Range alarm?
a.) Low battery power.
b.) The human body is also a source of interference; when carrying
both iPhone & Charm Tag, carry them on the same side of your
body.
c.) Interference/block by metal objects or high power signals used
by 2.4 GHz band devices (i.e. Wi-Fi networks or Microwave
ovens…).
Please change batteries if audible alarm becomes weak.
7
Mode option and tap 'Reconnect' to connect all devices. If all
devices are in sleep mode, please press and release device
button to wakeup each device. In this case, you have to exit App
and Run again to reconnect all device (this may take up to 20
seconds for device in SLEEP mode).
c. Press and release device button, Device will wake up from sleep
mode and send connection request to iOS DEVICE. iOS DEVICE
Will automatically connect to this device with "Connected"
message.
d. To temporarily stop using one or more devices, enter sleep mode
for each device. Hold device button for over 3 seconds until you
hear the first beep or the status LED light blinks Red. If you are still
in connect mode, a link lost alert will register to iOS DEVICE and
iOS will issue Alert Sound with 'LinkLoss/sleep' message. Tap that
row to stop Alert Sound. You can wakeup that device by press and
release device button once. iOS Device will detect wakeup signal
and enable connection automatically.
e. Device LED will stop blinking when it is in sleep mode.
f. You can remove device permanently by tapping the red Remove
button(Figure 13) in the upper right corner of the SetView page. To
delete this device(Figure 14) ,Please GO TO your iOS Device
Settings menu, select General/Bluetooth . You should see the
name of the device you want to remove, tap it and choose "Forget
this device".
9
Page 2
Figure 10 Figure 11
Figure 12
Figure 13 Figure 14
Figure 15
Delete device
HiProx_CXXXXX
Forget device
Remove device
Option A: After Airplane Mode has been turned 'ON'.
Press and release device button once for each device to disable alert
sound. Please go to Help/AirPlaneMode option: tap the
button by select [YES] to disconnect all Devices and exit App now
(please follow instructions from App)
To reconnect to all devices: tap the button and choose
[RECONNECT] and exit App now (please follow instructions from
APP). If you can not connect all devices at once, please repeat
AirPlaneMode disconnect / reconnect steps to RECONNECT all
devices.
Option B: Enable sleep mode for all devices:
Press and release device button over 3 seconds for each device, you
should hear beep once to confirm sleep mode. Your iOS DEVICE will
register 'LinkLoss/Sleep detected' message and go to Help/AirPlane
Mode to disconnect all devices (please follow instruction from App)
and exit App now. You can go to setting and turn 'ON' the Airplane
Mode.
To reconnect the all devices: you have to wakeup each device by
press/release device button once. Tap the button and
choose [RECONNECT] and exit App now (please follow instructions
from APP). If you can not connect all devices at once, please repeat
AirPlaneMode disconnect / reconnect steps to RECONNECT all
devices.
AirPlane Mode
10
Stop using device
11
a. To DISCONNECT all active device, please go to Help/ AirPlane
Mode option and tap 'YES' to disconnect all devices. Device
will enter standby mode after 30 seconds. Green LED will blink
every 10 seconds to indicate standby mode.
b. To RECONNECT all active device: please go to Help/AirPlane
Remote control for Photo Capture
To use the 'Photo' remote control function, go to the SetView page
and tap the Capture button to go to Capture View. The Smart Tag
remote key can control your smartphone camera function for photo
capture with one second per 'capture count number' or one minute
per 'capture time'.
For the Photo Capture function: You can use '+' or '-' to increase or
decrease the 'Capture count number' up to 100 images. Press the
smart tag remote button to start photo image capture one image per
second for the specified capture count period (you only press the
remote button once and you can pan your camera around your
target area).
8