User's Manual

A) Charm Tag Unit x 1 B) Strap x 1
C) Battery(CR 2032) x 1 D) User Manual x 1
If any components are missing from the package, please return the
product to your dealer immediately.
Product Description
3
Charm Tag User Manual
1 Introduction
Quick Setup Guide
Specification
Product description
2
4
1 Introduction
5
Quick setup guide
Page 1
Package components
3
Communication Standard Bluetooth® 4.0 Low Energy Wireless Technology
Compatibility
iPhone 4S/5, iPad 4, New iPad, iPad Mini with iOS 6 or later
Search Range
164ft/50m(*Distance will vary depending on terrain and other factors.)
Alert Range 6~50ft/2~15m adjustable (Near: 16±10ft/5±3m, Far: 32±16ft/10±5m)
Battery Type CR2032x1
Battery Life 6~12 months
Dimension/Weight 38x25.6x10.7mm (1.5x1x0.42inch) / 4.2g (0.15oz.)
Working Temperature
Temperature: 5℃~40℃, humidity : 20%~80%
Step 5 - Run ”HiProx Multi” application
a. Open ”HiProx Multi” and tap the button in the upper right
corner to discover all available devices.(Figure 4)
b. ”HiProx Multi” will pop up Bluetooth Pairing Request.(Figure 5)
c. Select ”Pair” from ”Bluetooth Paring Request” for each device. The
Green LED light will blink once every 5 seconds in the connecting
mode.
Step 6 - Test the Charm Tag system
a. From MainView available devices table, you can tap desired item to
select that device. Once device has been selected, button will
appear in that row.(Figure 6)
b. To set different alarm sounds for each tag, press 'Alarm Button'
(Figure 7)and go to Alarm Sound Selection View to choose your alert
tone for that tag.
c. Press button, the Charm Tag will beep to do FindMe function.
d. Press ”FindMe” button on the Charm Tag unit , and your BLE device
will beep.
e. Press and release ”Find Me” button to stop the FindMe function.
f. Set alarm ”threshold level” depends on the alarm distance you like.
Step: Range Alarm Threshold Move the threshold bar
depends on the distance alarm you need.(Figure 7)
g. Test your setup by placing the iPhone in a stationary location. Then
take the Reminder and walk away from the iPhone - when you reach
6-50 feet from the iPhone, the Reminder will begin to beep. If you
move back into the range, the alarm will cease. (Figure 9)
6-50 Feet
a. To locate the missing item, tap green button from available
device st. The missing device will continue beep for 5 seconds
from each request. Re-tap green button again to continue
searching function.
b. Press and Release Device 'FindMe' button (hardware button under
the LED) will gernerate ”FindMe Request” from that Device. Your
iOS device (iPhone / iPad...) will issue Alert sound continuesly.
Press and Release Device FindMe button to stop this request.
c. Tap green button from iOS Device will Mute 'FindMe Request
Alert Sound.
d. Holding the device button for over 3 seconds will force the device
to enter SLEEP mode and generate a linkLossAlert to the iOS
device; to wake up and re-connect to the iOS device, ress and
release device button.
FindMe Function
6
Figure 9
1. Enter Help menu
2. Find new device
3. Find my tag
4. Setting button
5. Signal indicator
6. Remove tag button
7. Beep sound setting for tag
8. Change device name
9. Battery status
10. On/Off call alert function
11. On/Off link loss function
12. On/Off range alarm function
13. Set alarm range
14. Alarm sound setting
15. On/Off Map location function
16. Enter Map view menu
17. Enter Camera function
18. Enter airplane mode setting
Figure 4 Figure 5
Figure 7
Figure 6
Figure 8
2
18
1
Signal Indication
3 4
5
8 97
14
10
11
12
13
15
16
17
6
Beep Sound High Alert: 95±3db, Mid Alert: 90±3db (at 10cm/3.9inch)
Power Switch
Front Back
LED & Device
FindMe Button
Buzzer
Hanging hole
for strap
Top cover
Bottom cover
Step 1 - Download App ”HiProx Multi”
Download ”HiProx Multi” on App Store for free.
(Please search for HiProx Multi on App store, or search for BLE
and find the HiProx Multi application)
Step 2 - Enable Bluetooth on your iPhone/iPad
Go to Setting General Enable Bluetooth
Step 3 - Place battery into Charm Tag Units
a. Remove the top cover with your hand. Force the top cover to
slide from its mounted position towards the top of the
Charm Tag.
(Figure1 & Figure 2)
b. Insert the battery into the battery compartment with the the ”-”
sign on the battery facing up. Then replace the top cover
by sliding it down into compartment opening.
(Figure 3)
Step 4 - Turn on the Charm Tag Units
Once turn on the Charm Tag units, and it will enter automatically
to pairing mode. Green LED will blink per second to indicate
device is ready to pair.
Figure 1 Figure 2 Figure 3
An electronic leash that will sound an alarm when your iPhone leaves
your vicinity. You can also use your iPhone to find the lost Charm Tag
thanks to the duplex communication protocol. A handy app called
HiProx Multi, will show on Google Map the last time the Charm Tag and
phone were connected. As a remote shutter release for self-portraits or
to prevent blur by shaking camera. The app can control the alarm
threshold distance, set the Charm Tag to start beeping when a call is
incoming, and switch the proximity alarm on/off. HiProx Multi for use
with multiple Charm Tag units and includes all of the mentioned
features. Simple to use interface allows you to re-name each tag
attached to your valuables, such as Keys, Wallet, etc. A brilliant little
device that could save you a lot of trouble.