User's Manual

Page 3
Page 4
How to set up
EZlock Mobile App User Guide EZlock Mobile App User Guide
6. Share keys
You can add two sets of Master Keys, seven sets of User Keys and 24 sets of Guest Keys.
a) Ask the future user to download ‘EZlock App’ and Run the App.
From the ‘EZlock’ App -> Key option and select ‘Request Key’. The email service App will ask
the user to send this request to you. The content of the email has the unique ID. (Fig-8)
Fig-7
b) After you have received the ‘Request Key’ email, copy the ‘Unique ID’ string and paste to ‘New
Key’ User ID �iled. (Fig-9)
From: Lock Setting -> Shared Keys option ‘+’ to add New Key.
Note: Only Guest key has expiration date requirement as shown in Fig-9.
c) Press ‘Save’ to con�irm this request. Based on the User ID, the App will generate an encrypted
key for this user. Each encrypted Key can only be used once. If any error occurred, delete this
key and start over again. The App will guide you to send this email to the user.
d) The future user will open ‘Lock Key’ email and tap the attached �ile then the App will guide you
to select ‘EZlock’ App to accept this �ile as shown on Fig-10:
e) After importing the ‘Lock Key’ �ile, the App will accept or reject this new Key.
If key has been accepted, test the EZlock Lock. The App will perform an auto scan to register
this Key to the system. When the new key passes the security check, you can control the door
according to the share key setting.
EZlock has 40 sets of unique electronic ID keys, these keys canot be duplicated or transfered. Each
key can only be registered to the EZlock App once. Each sharing key can only be issued by Admin
or Master. Admin key has the ability to grant / revoke each key access for weeks, hours and
minutes.
• Admin key x 1, can share two Master keys and 12 sets of Guest key to other smartphones.
• Master key x 2, each can share 6 sets of Guest key.
• Guest key x 24, each temporary key can be sent by email. After the expiration date, it will be
• Key Fob x 6, each has no expiration date. It provides safe and easy access to young family
members and a 5 meters remote access radius. Please refer to ‘Key Fob’s registration manual’
for more information.
• Opening doors is easily accomplished touching the Deadbolt Rose (Fig-3) or using pre-pro
grammed hand gestures in our mobile app.
7. EZlock Key Fob’s registration and auto calibration
Key Fob Battery installation and replacement: (Fig-a)
Key Fob registrations steps:
a. In front of the EZlock Lock, press and hold Key Fob’s button (Fig-b) and turn ‘Power Switch’ to
the left (on) at the same time. A rapid RED �lashing LED comes up (about 3 seconds), Key Fob is
ready to register with the EZlock Lock.
Fig-8 Fig-9
Fig-10
b. Continue to hold the button and turn ‘EZlock Turn-piece’ to
open and then close again, An Orange Light ring comes up
from EZlock and Key Fob’s LED will turn Orange (Fig-c). You
are in Registration mode now. Release the Key Fob button at
this time. EZlock will provide a unique ID for the Key Fob to
register for registration.
c. If Key Fob registration is successful within 30 seconds, the
EZlock Lock and Key Fob will beep in con�irmation. To
complete the process the Key Fob’s LED will turn off. If you do
not hear ‘Con�irmation Beeps’ and continue to see Red LED
�lashing, please switch off the ‘Key Fob’ power and repeat
these steps again. (Only one ‘Key Fob’ is included in the
shipping package, EZlock Lock can support up to 6 Key Fobs.
You can order extra Key Fobs from the distributors).
4. Touch Unlock: (Fig-7)
The EZlock has a built-in touch sensor, with your smartphone and the Mobile App
must run on the background. This function only allows once to unlock the door by
touch sensor from each entrance. Requirement for Touching Unlock: the active
smart phone should be in the out of range distance, 20 meters above for more than
50 seconds to enable these functions. When EZlock touch sensor function is ready,
the Rose Light Ring will show a �lashing White light. You can touch the Deadbolt
Rose to open the door at this moment.
Hint: You can remove the App from background to disable this function.
Fig-c
Fig-a
on off
Fig-b
5. Near Field Unlock
Use your smartphone with the Mobile App running in the background, then make it activated
(bring up its screen) in front of the EZlock Deadbolt (less than 1-2 cm/ 1 inch), the door will be
unlocked within 3 seconds.
8. Trouble shooting: Hardware Reset
If you lost your Admin Key or Master Keys; User Keys or Key Fobs for any reason, you can do a
hardware reset to prevent any illegal entry. After resetting the hardware, the EZlock system will
generate new sets of unique IDs for all Keys. Hence, please delete the “Lock” from the App �irst
and then go through the registration process to enable each key as described in previous steps.
Hardware Reset Requirements and procedures:
Unlock the door by using any key or use an emergency standard key; remove the EZlock device
cover and batteries.
Unscrew three screws and detach the Rose Light Ring cable from the EZlock device.
You will see the hardware reset button on the back of the controller board.
Install three batteries �irst, press and hold the Reset Button on one hand and install the fourth
battery.
You should see the Red LED come up and start �lashing (Hardware Reset Mode).
Release the Reset Button once you have entered the Hardware Reset Mode. EZlock will erase all
Key records from the system.
d. Key Fob registration is complete now and press Key Fob button to unlock the door.
e. The Key Fob has a 9-12 months battery life. When the battery is low, the Red LED will �lash
slowly accompanied by beeping. Please replace the CR2032 coin battery as soon as possible.