Parts List Quantity Part Descriptions Wall, Floor, Roof Panels 30 Wall Columns 4 Door Frames 5 Roof Side Rails 2 Roosting Bar Parts 2 (Roosting bar might not be included for certain models.
Notes X X When installing wall panels, make sure the two connecting panels are at a 90 degree angle vertical to the ground, and 90 degree perpendicular to each other. Tilting in any way might cause damage to the groove. Part Label. All Parts are labeled in the sequence of assembly.
IMPORTANT ASSEMBLY TIPS Before launch our new ecoFLEX® product line, we have conducted hundreds of testing and surveys with end users. Thanks to all the participants and their feedbacks, now we have these valuable tips to pass on to you ... :) Assemble on a hard, flat surface. Once assembled, you can easily move the house to the location desired. :) Sort the parts in sequence.
Step 1. Step 2. CD has no This side of column assembly hole on top. Note the position of this floor support bin is facing away from column CD. Note: After install Panel G), make sure the FLAT side of panel and G) are facing inside, and the washed sides are facing out.
Step 3. Step 4. Move assembled parts@&@and near to each other. Lift@upward as shown, then tilt@&@so@is perpendicular to@. lnsert@into@.
Step 5. Step 6.
Step 7. STOP Assembly holes So far you have setup the wall base panels, a),®, ® & @; and the 4 column posts. Step back and stand facing the front door open. Do a quick check: • The FLAT SIDES of the all wall panels are facing inside. • The floor support bins are located on the lower edge of the flat side of the wall panels. • The assembly holes on the two front columns CD &@are facing forwards; while the assembly holes on the two back columns ® & (J) are facing each other.
Step 8. Step 9.
Step 10. Hold panel (g) Step 11 . (for selected models) at the two corner cutouts. Slightly angel @ into @. Release panel@, then gently push it down. Note: If you chicken barn comes with 2 roosting bars. Put the roosting bars@and@into the U-shaped slots on wall panels@and@.
Step 12. Step 13.
Step 14. 11 Step 15.
Step 16. Step 17. Insert one end of a pin @ into the hole in door panel@, the other end into the hole in door frame @. Repeat on the other side. Place the assembled unit in the door opening as shown. Place door frame @ into one of the lower corners of the door opening, then push the other end down gently. The side of the frame piece with part# bar code should be facing inside the barn. Same for all door frame pieces.
Step 18. Attach door frame @ to panel @ in the same fashion as Step 16. 13 Step 19. Hold door frame @ and wall panel @ together, insert wall panel @ into place.
Step 20. Step 21.
Step 22. 15 Step 23.
Step 24. Step 25. Parts @ and @ should be installed with the flange attaching to the inside of the wall panels.
Step 26. Step 27. Insert the edge of Part @ with the corner cutouts first.
Step 28. Step 29. Tilt@ as shown. Align the top of @ with the notch in @. Push to lower part of @ sideways until vertical.
Step 30. Step 31. At an angle, place @ on the top edge of® between@ and@. Then push down gently. Install @ the same way as@.
Step 32. Step 33. Insert nesting box floor@. Note the notches at the front and back are different. Check alignment to make sure the floor is inserted correctly.
Step 34. Locking Nesting Box (optional): To lock the nesting box, insert the 15/16" Thumb Screw into a hole on the side of the cover of the nesting box. Screw all the way in. Remove the Thumb Screw when to open and retrieve eggs.
Cleaning Instruction It is very important to keep the barn clean for healthy chickens. The Easy to Assemble design will be appreciated when it is time to clean. Remove one or more roof panels by reversing step 28 and 27 of the assembly instruction. You now have access to the entire inside of the house. We recommend using a detergent with strong grease cutting capabilities and safe to use around you, your kids and the chickens. After washing, rinse and then wipe down the panels.
