Integrated Amplifier A32 Power Amplifier P35
Using this handbook This handbook has been designed to give you all the information you need to install, connect, set up and use the Arcam A32 integrated amplifier or the P35 power amplifier. The A32 amplifier is described first, then the P35. The CR-389 remote control handset supplied with the A32 integrated amplifier is also described. CONTENTS Your amplifier(s) may have been installed and set up by an authorised Arcam dealer.
Safety guidelines 9. Power sources Only connect the appliance to a power supply of the type described in the operating instructions or as marked on the appliance. SAFETY INSTRUCTIONS This product is designed and manufactured to meet strict quality and safety standards. However, you should be aware of the following installation and operation precautions: 10.
Installation: A32 integrated amplifier L PHONO R SP2 4 – 16 OHMS TRIG OUT VOLTAGE SELECT L REMOTE IN POWER INLET 1 115/230V 2 R + R – 3 MM MC L INTEGRATED SP1 + L – R PRE/PWR PWR IN 4 PRE OUT 567 RECORD PLAY OUT IN TAPE/PROC RECORD PLAY OUT IN VCR/TAPE 2 DVD AV TUNER CD AUX 8 9 bk bl bm bn bo bp bq br Arcam A32 amplifier POSITIONING THE UNIT + – + Place your amplifier on a level, firm surface. Avoid placing the unit in direct sunlight or near sources of heat or damp.
bn – Connect this input to audiovisual equipment such as a VCR, AV laserdisc player, satellite or Nicam tuner. CONNECTING TO A POWER SUPPLY TUNER tuner. WRONG PLUG? Check that the plug supplied with the unit fits your supply and that your mains supply voltage agrees with the voltage setting (115V or before plugging in. 230V) indicated on the rear panel of the unit If your mains supply voltage or mains plug is different, consult your Arcam dealer or Arcam Customer Support on +44 (0)1223 203203.
Using your A32 integrated amplifier 1 5 6 A32 INTEGRATED AMPLIFIER ENTER MODE RECORD PHONO/AUX SELECT 2 3 4 CD 7 DVD VCR TAPE TONE 9 SP1 and SP2 SP1 SP2 bk PHONES POWER bl bm bk These buttons allow you to select and deselect the main (SP1) and secondary (SP2) set of speakers attached to your amplifier. The light above each button glows if the corresponding speakers are currently selected.
RECORDING With the Arcam A32 it is possible to listen to and record from one source, or to listen to one source while recording another. Both sets of tape sockets are identical in sensitivity and suitable for use with almost any type of recorder (cassette, CDR, MD, VCR, reel-toreel, etc.). The record signal is sent to both the TAPE and VCR output sockets. RECORD 3 To record the currently selected source, press RECORD until the display shows ‘RECORD SOURCE’.
Setting up your A32 integrated amplifier INTRODUCTION ‘Switch on’ state DOWN The A32 allows you to adjust listening settings to suit your taste, and to customize various features of the amplifier to fit your system. Use this diagram to help you navigate through the settings available. UP VOLUME Adjust LEFT The ENTER and SELECT buttons are represented in the diagram by the symbols and respectively. RIGHT BALANCE The Control knob is shown as Adjust –dB .
Using the remote control CR-389 REMOTE CONTROL The CR-389 remote control gives access to all functions available on the front panel of the A32. It also has controls to operate Arcam CD players, AM/FM tuners and DAB tuners. The remote control transmits Philips RC-5 type codes. TUNER These buttons are used to control tuner functions. Note that the FM/DAB lights indicate into which mode you are switching the remote control. The lights only illuminate for five seconds to conserve battery power.
Installation: P35 power amplifier + R/CH1 – + L/CH2 – + CTR/CH3 – SP2 SP2 AUDIO 4 – 16 OHMS TRIG OUT 230V VOLTAGE SELECT POWER INLET LINK L R + R/CH1 – AUDIO IN SP1 SP1 REMOTE IN CTR/CH3 4 – 16 OHMS + L/CH2 – OUT IN + CTR/CH3 – OUT Optional Third Channel Module – provides a third 90W channel suitable for Home Cinema or multi-channel audio use. CONNECTING TO OTHER EQUIPMENT REMOTE SWITCHING Follow the installation instructions for the integrated amplifier on pages 4–6.
Using your P35 power amplifier P35 POWER AMPLIFIER SP1 SP2 POWER POWER (AND POWER INDICATOR LIGHT) SP1 AND SP2 Switches the unit on and off. The light indicates the status of the amplifier. These buttons allow you to select and deselect the main (SP1) and secondary (SP2) sets of speakers attached to your amplifier. An indicator light shows which set of speakers are currently selected.
Bi-wiring and bi-amping loudspeakers BEFORE YOU START BI-AMPING YOUR SYSTEM The performance of your system can be further enhanced over that achieved with bi-wiring, by extending the principle one stage further to include separate amplification for the low and high frequency drive units in each loudspeaker enclosure. WARNING: Do not make any connections to your amplifier while it is switched on or connected to the mains supply.
Technical specifications A32 P35 Continuous power output (20Hz—20kHz at 0.5% THD), per channel Both channels, 8Ω, 20Hz—20kHz 100W Single channel, 8Ω, 20Hz—20kHz 150W Both channels, 4Ω, 20Hz—20kHz 140W Single channel, 4Ω, at 1kHz 200W Three channels, 8Ω, 20Hz—20kHz – Harmonic distortion, 80% power, 8Ω at 1kHz 0.
Service information Before returning your amplifier for service, please check the following: SOUND CUTS OUT FOR NO REASON Note that because of the high output voltage from a CD player, it is possible to drive the A32 at full power even though the volume is not set at maximum. If the temperature of the internal heatsink rises above a safe level, then a thermal cutout inside the amplifier will operate.
PEMBROKE AVENUE, WATERBEACH, CAMBRIDGE CB5 9PB, ENGLAND telephone +44 (0)1223 203203 fax +44 (0)1223 863384 email support@arcam.co.uk website www.arcam.co.
