Product Specification Product Specification WN8522B-LF-ZZ IEEE Dual Band 802.11n USB2.0 Adapter v.
Product Specification Table of Contents Chapter 1 Introduction ________________________________________________________ 4 1. Introduction ________________________________________________________ 4 1.1 Product Features____________________________________________________ 4 1.2 Applications _______________________________________________________ 4 Chapter 2 Hardware _______________________________________________________ 5 2.1 General Overview __________________________________________________ 5 2.
Product Specification Revision History Edition # V 01 Reason for revision ♦ Initial Document Issue date Dec 22th 2009 Written by Troy Chen ♦ WN8522B 3
Product Specification Chapter 1 Introduction 1. Introduction WN8522B is a dual band wireless 802.11n USB Adapter which enables wireless networking systems to attain data communication speeds up to 300 megabits-per-second (Mbps), while remaining backward compatible to the existing installed base of Wi-Fi systems worldwide. It supports operation to the IEEE 802.11a/b and IEEE 802.11g ,and draft IEEE 802.11n standards. WN8522B will enable a next generation of high-data-rate platforms for operation in the 2.
Product Specification Chapter 2 2.1 ♦ ♦ Hardware General Overview USB 2.0 Interface and 802.11 n chipset-on-board design. Antenna: 2 Internal Antenna on board 2.2 Hardware Architecture Broadcom 4323 single chip USB2.0 2.3 Main Chipset Information BCM4323: MIMO MAC + Baseband processor and RF with fully forward compatible with IEEE 802.11n draft2.0 standard. 2.4 PCB dimension PCB dimension : 2.0 cm x 5.
Product Specification Chapter 3 Software 3.1 Operating System Supported ♦ Windows 2000 , Windows XP, Windows Vista 3.2 Wireless Mode Supported ♦ AP (Infrastructure) Client mode ♦ Ad-hoc mode 3.3 Security ♦ AP (Infrastructure) mode supports ♦ Static WEP that support both 64 and 128 bit keys. ♦ WPA(TKIP) with PSK ♦ Ad-hoc mode supports ♦ None (plaintext) ♦ Static WEP that supports both 64 and 128 bit keys. 3.
Product Specification Chapter 4 WN8522B Appearance LED1 One Power/Link (Green/Blue) OFF All others states ON Radio On and Associated Blink Radio On and Scanning Flash Radio On and Associated and TX/RX Data LED2 WPS/Security Blue OFF No security/Not connected ON Connected with security Blink In the process of connecting 7
Product Specification WN8522B 8
Product Specification Chapter 5 ♦ Specifications Frequency Band: Draft 802.11n Radio: 2.4 GHz 802.11g Radio: 2.4 GHz 802.11b Radio: 2.4 GHz USA – FCC Canada – IC Europe – ETSI Japan – STD-T66/STD-33 2412~2462MHz (Ch1~Ch11) 2412~2462MHz (Ch1~Ch11) 2412~2472MHz (Ch1~Ch13) 2412~2484MHz (Ch1~Ch14) 802.11a Radio : 5 GHz 5.150~5.250GHz 5.250~5.350 GHz 5.470~5.725 GHz 5.725~5.850GHz ♦ Operating Channels: IEEE 802.
Product Specification CCK@5.
Product Specification References ♦ ♦ ♦ ♦ BRCM Reference Design Functional Specification IEEE 802.11b Standard Specification IEEE 802.11g Standard Specification IEEE 802.
Product Specification Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Product Specification IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module.
Product Specification than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. The drawings, specifications and the data contain herein are the exclusive property of Arcadyan Technology Corp.
