User’s Manual User’s Manual WN7522C_1-LF-19 IEEE Single Band 802.11n USB2.0 Module v.
User’s Manual Table of Contents Chapter 1 Introduction ________________________________________________________ 4 1. Introduction ________________________________________________________ 4 1.1 Product Features____________________________________________________ 4 1.2 Applications _______________________________________________________ 4 Chapter 2 Hardware _______________________________________________________ 5 2.1 General Overview __________________________________________________ 5 2.
User’s Manual Revision History Edition # V 01 Reason for revision ♦ Initial Document Issue date Written by Dec 5, 2008 Katherine Hsieh ♦ WN7522C 1 3
User’s Manual Chapter 1 Introduction 1. Introduction WN7522C 1 is a single band wireless 802.11n USB module for Blu-ray players and other multi-media devices. It enables multi-media devices to connect onto 802.11n WLAN network and attain data communication speeds up to 300 megabits-per-second (Mbps). It is also backward compatible to the existing installed base 802.11b/g network. 1.1 Product Features ♦ High speed for wireless LAN connection, RX up at 300 Mbps data rate.
User’s Manual Chapter 2 2.1 ♦ ♦ Hardware General Overview USB 2.0 Interface and 802.11 n chipset-on-board design. Antenna: 2 Internal Antenna on board 2.2 Hardware Architecture Broadcom 43231 single chip USB2.0 2.3 ♦ Main Chipset Information BCM43231: MIMO MAC + Baseband processor and RF with integrated 2.4GHz PA 2.
User’s Manual Chapter 3 Software 3.1 Operating System Supported ♦ Windows 2000, XP, Vista ♦ Linux Driver 3.2 Wireless Mode Supported ♦ AP (Infrastructure) Client mode ♦ Ad-hoc mode 3.3 Security ♦ AP (Infrastructure) mode supports ♦ Static WEP that support both 64 and 128 bit keys. ♦ WPA(TKIP) with PSK ♦ Ad-hoc mode supports ♦ None (plaintext) ♦ Static WEP that supports both 64 and 128 bit keys. 3.
User’s Manual Chapter 4 WN7522C 1 Appearance 7
User’s Manual Chapter 5 ♦ Specifications Frequency Band: Draft 802.11n Radio: 2.4 GHz 802.11g Radio: 2.4 GHz 802.11b Radio: 2.4 GHz USA – FCC Canada – IC Europe – ETSI France Japan – STD-T66/STD-33 ♦ Operating Channels: IEEE 802.11b/g/n compliant: 11 channels (US, Canada) 13 channels (ETSI) 4 channels (France) 14 channels (Japan) ♦ Transmit Power and Sensitivity: TX Output Power:(Typical) 11b 16.5 +/- 1 dBm 11g 16.5 +/- 1 dBm@54Mbps 11n 15.
User’s Manual QPSK@12/18Mbps 16-QAM@24Mbps 64-QAM@48/54Mpb and above ♦ Current consumption(5V DC): TX: 380mA Max, @MCS7, 40MHz RX: 350mA Max, @MCS15, 40MHz Power Saving: < 50mA Radio OFF mode: < 100mA ♦ ♦ ♦ Operating Temperature: 0 ~ 40 oC ambient Storage Temperature: -10 ~ 70 oC ambient Humidity: 5 ~ 90% and must be non-condensing ♦ Regulation and certification compliance available: ♦WHQL ♦ETSI/CE ♦ESD: EN61000-4-2, which specifies 4kV contact and 8kV air discharge.
User’s Manual References ♦ IEEE 802.11b Standard Specification ♦ IEEE 802.11g Standard Specification ♦ IEEE 802.11n draft Standard Specification FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
User’s Manual 2.4GHz operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into.
User’s Manual IC Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la class B est conforme a la norme NMB-003 du Canada.
User’s Manual required to be available in the users manual: This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX IC : 4711A-WN7522C ".
