IN-WALL WAVE 2 WIRELESS ACCESS POINT Quick Start Guide AN-510-AP-IW-AC
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Araknis Networks Wireless Access Point Quick Start Guide Industry Canada Statement This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
Araknis Networks Wireless Access Point Quick Start Guide Industry Canada Statement, Continued Radiation Exposure Statement: This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d’exposition aux radiations: Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un environnement on contrôlé.
Araknis Networks Wireless Access Point Quick Start Guide CE Statement This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. All operational modes: 2.4GHz: 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40) 5GHz: 802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40), 802.
Welcome to Araknis Networks™ Thank you for choosing an Araknis™ WAVE 2 AC Wireless Access Point (WAP). With newly designed rounded housing, an convenient on-wall mounting system, convenient PoE power( in & out), and the latest WAVE 2 AC wireless technologies, these products are ideal as staples in both residential and commercial applications. Features • 2x2 Dual-Band WAVE 2-AC 1300Mbps • Sleek Design • Unobtrusive Recessed Lighting • 1 x Gigabit LAN Port (w/802.3at PoEIN) • Easy On-Wall Install.
Araknis Networks Wireless Access Point Quick Start Guide Step 1: Unbox Wireless Access Point Mounting Bracket Quick Start Guide (WAP)* Tile Ceiling Mounting Hardware © 2019 Araknis Networks® Drywall Mounting Hardware Wood Surface Mounting Hardware 7
Step 2: Install On-Wall A Wall B In-Wall Bracket (accessory sold separately) In-Wall Wall In-Wall Plate and linkage WAP WAP NOTE: In-Wall Mounting Accessory sold separately. Refer to in-wall bracket Quick Start Guide for installation instructions. 8 Support: 866.838.
Araknis Networks Wireless Access Point Quick Start Guide Connect: Port Identification B C D E A A. LAN 1 - PoE In- Connect to main Switch or Router. B. Reset - Use a pin or paper clip to press and hold to reset to default settings. C. LAN 3 - PoE Out - Connect to Compact PoE powered switch. D. LAN 2 - Connect to switch or to PoE injector from switch. E. 48V DC - Connect power supply to this port. NOTE: Note Re: PoE Out functionality coming soon.
PoE Situations Please provide information for this page @nancy - need the following information: - when using dc psu to power device... * what max powere and distance can the product support for PoE Out (eg. 100M up to 802.3af?) * what is the max poe out that product can support (eg. 802.3at when under X distance) - when using PoE IN to power device * ditto * ditto 10 Support: 866.838.
Araknis Networks Wireless Access Point Quick Start Guide Step 3: Connect LAN WAN AN-310-SW-F-8-POE Internet Router PoE Switch WAP POWER + DATA (OUT) LAN WAN AN-ACC-INJ-30W DC 48V Input Power OR DATA (IN) AN-310-SW-F-8-POE Internet Router Switch PoE Injector (not included) DC Power Supply (not included) WAP ACTIVE PoE/+ 15W OUT LAN 30W IN WAN AN-310-SW-F-8-POE Internet © 2019 Araknis Networks® Router Switch WAP Compact PoE Powered Switch 11
Step 4: Verify LED LED Status: 12 • Blinking: WAP is not working correctly. Contact Araknis technical support. • Solid White: WAP is booting up. • Solid Blue: WAP is operating correctly. Support: 866.838.
Araknis Networks Wireless Access Point Quick Start Guide Step 5: Log Into Web Interface A Log in using the default credentials: Username araknis Password araknis NOTE: If you can’t connect to the WAP using this method, or need to configure the device before connecting it to the network, try these options for accessing your device: • DHCP IP address – Page 15 • Default IP Address – Page 16 • OvrC – Page 19 © 2019 Araknis Networks® 13
Pro Tip: Save and Apply Changes After making changes to settings on a menu page, click the “Save” button on the menu to hold the new settings in the Apply Changes field. After all desired changes have been made, click “Apply Changes” to review the new settings if any. Click "Apply" to make the changes or "Revert" to cancel the changes. NOTE: Settings will take affect after the progress bar completes 100%. 14 Support: 866.838.
Araknis Networks Wireless Access Point Quick Start Guide Other Access Methods: DHCP IP Address The WAP is configured to DHCP by default so that the DHCP server can assign an IP address when the WAP is connected to the network (the DHCP server is usually the router). This address can be used for accessing the web interface. Use one of these methods to find the IP address of the WAP: • Check the client table on your router • Use a network scanner (e.g. Fing) to sniff the network.
Other Access Methods: Default IP Address If the WAP is not issued an IP address on the network, or needs to be accessed while not connected to a network, you can configure your computer's network connection to allow access using the default IP address, “192.168.20.253”. Windows 7 screenshots shown for reference. A Connect your PC to the WAP using a network patch cable. Computer 16 B On your PC, open the Control Panel and left-click “Network and Internet”. C Left-click “Network and Sharing Center”.
Araknis Networks Wireless Access Point Quick Start Guide Other Access Methods: Default IP Address Windows 7 screenshots shown for reference. D In the left bar, left-click “Change adapter settings”. © 2019 Araknis Networks® E Right-click the icon for the wired network connection and left-click "Properties". F Left-click to highlight “Internet Protocol Version 4 (TCP/IPv4), then left-click “Properties”.
Other Access Methods: Default IP Address Windows 7 screenshots shown for reference. G In the “General” tab, left-click "Use the following IP address:" and enter the IP address and subnet mask. 18 IP Address 192.168.20.2 Subnet Mask 255.255.255.0 H Left-click “OK” to close Internet Protocol Version 4 (TCP/IPv4) Properties, then left-click "OK" to close wireless network connection properties. I Open a browser and navigate to http://192.168.20.253/.
Araknis Networks Wireless Access Point Quick Start Guide Other Access Methods: OvrC OvrC gives you remote device management, real-time notifications, and intuitive customer management, right from your computer or mobile device. Setup is plug-and-play, with no port forwarding or DDNS address required. To add this device to your OvrC account: A Connect the WAP to the Internet B Log Into OvrC (www.ovrc.
Warning This product can expose you to chemicals including lead and lead compounds, which are known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov. Contacting Technical Support P (866) 838-5052 E techsupport@araknisnetworks.com 2-Year Limited Warranty Araknis Networks® products have a 2-Year Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use.
