ITEM #0065461 0065459 ROMAN TUB FAUCET MODEL #461-5301 461-5327H2 AquaSource® is a registered trademark of LF, LLC. All Rights Reserved. Francias / Español p. 9 ATTACH YOUR RECEIPT HERE Serial Number ____________ Purchase Date ____________ Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-417-7564, 8 a.m. - 8 p.m., EST, Monday - Friday. Lowes.
PACKAGE CONTENTS B C D E A F G N O H P Q J U R T I S K L M PART A B C D E F G H I J K L M N O P Q R S T U DESCRIPTION Spout Screw (Preassembled to Spout (A)) Cap (Preassembled to Spout (A)) Handle Cap Handle Screw Handle Handle Base Plastic Cap (Preassembled to Hot End Valve (U) and Cold End Valve (J)) Flange (Preassembled to Hot End Valve (U) and Cold End Valve (J)) Cold End Valve Rubber Washer (Preassembled to Hot End Valve (U) and Cold End Valve (J)) Metal Washer (Preassembled to Hot End Valv
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate, or install the product. WARNING: Follow the installation instructions carefully. Proper installation is the installer’s responsibility. Failure to follow correct installation procedures can result in the faucet being loose, which can result in serious injury. CAUTION: Check local building codes before beginning installation to ensure compliance.
ASSEMBLY INSTRUCTIONS 1. Shut off the water supply and remove the old faucet. 1 Note: Each valve stop should be turned clockwise. 2. Drill holes in the diagram. deck (not included) per this 2 Note: This kit is intended for installations up to 2 in. thick. 8~16 in. 1-3/8 in. 1-1/8 in. 3. Remove the plastic caps (H) from the cold end valve (J) and hot end valve (U). 3 H J,U 4 Lowes.
ASSEMBLY INSTRUCTIONS 4. Install the cold and hot end valves (J and U): 4 (I) from the top a. Remove the preassembled of the cold end valve (J). b. From underneath the deck, insert the cold end valve (J) with the preassembled rubber washer (K), metal washer (L), and nut (M) through the hole on the right side. c. From above, thread the the cold end valve (J). I (I) onto the stem of U (I) sits J d. Tighten the nut (M) so that the to the surface of working area. K e.
ASSEMBLY INSTRUCTIONS 7. Remove the preassembled screw (B) and cap (C) from the spout (A) and place the spout (A) onto the middle body (P). Then secure the spout (A) with the screw (B) and insert the cap (C). 7 A B C P 8. Connect one end of each hose (T) to the two connectors on the middle body (P) and the other end of the hoses (T) to the cold end valve (J) and hot end valve (U). Gently bend the hoses (T) to in the available space underneath the deck. 8 P U J T 9. Connect a 1/2 in.
OPERATING INSTRUCTIONS 1. After the installation is complete: 1 a. Turn on the water supply and allow both hot and cold water to run for at least one minute each. b. While the water is running, check for leaks. CARE AND MAINTENANCE Clean carefully by gently wiping with a grit-free damp cloth. Use only mild soap with water. Never use acids, harsh chemicals, or abrasive detergents to clean the surface.
REPLACEMENT PARTS LIST For replacement parts, call our customer service department at 1-866-417-7564, 8 a.m. - 8 p.m., EST, Monday - Friday.
