Installation Guide

WALL INSTALLATION
8
1) Add sand.
2) Choose the filter location beside a round section (never in a
straight section). The starting point should be at that location where
the skimmer and return holes, and as close as possible to the fil-
tration system.
3) Before uncoiling the wall, make sure the pre-punched holes for
the skimmer and pump return are at the top and facing the planned
location of your filter.
PLANKS
ST
SAND
TA
AKES AND
STRINGS
BOTTOM PLATE
BOTTOM TRACK
PUMP RETURN
HOLE
WALL
SKIMMER HOLE
End
Begin inserting the wall into the bottom tracks in the middle of a
bottom plate. At first, the wall is kept in place with one or two stakes
and strings (or extra persons). One person uncoils the wall on a
beam or a plank, while a second person inserts it in the bottom
tracks. Do not uncoil more than 3 m (10') of wall before you install
a support bar or stake and string to reinforce the structure.
Once the wall is completely uncoiled, you may find that it is too
long or that both ends do not meet by a few centimetres. If such is
the case, adjust tracks and bottom plates until wall holes line up. If
this does not work, roll up the wall again, check measurements as
per chart 1.1, adjust tracks and plates, if applicable, and uncoil the
wall again. If the spread is too wide, measure the wall and check it
against the chart below.
Join both ends of the wall by orienting folds outward to hide the ex-
clamation icon. (Illustration 8.1)
Note: If the wall is attached properly, you should no longer see
the exclamation icon. If you can always see the icon, you must
reverse the overlap.
Insert bolts and nuts in every hole and tighten with wrench (screw
head on water side of wall). Tape over screw heads with duck tape.
DET
TA
AIL 8.1
8x14
36' 4 3/4"
(11,09m)
8x16 8x19 10x16 10x18 10x21 12x18 12x24 12x27 13x17
CHART OF ACTUAL LENGTHS OF STEEL WALL ACCORDING TO MODEL
41' 10 1/2"
(12,75m)
47' 4 3/4"
(14,42m)
42' 5"
(12,92m)
53' 5"
(16,25m)
47' 10"
(14,58m)
50' 7"
(15,42m)
61' 7"
(18,77m)
66' 12"
(22,00m)
48' 11"
(19,91m)
13x23 14x20 14x25 15x20 15x26 15x31 16x26 16x32 18x33 18x38 18x44
59' 10"
(18,24m)
55' 3"
(16,84m)
66' 3"
(20,19m)
56' 6" 67' 5" 78' 5"
(17,22m) (20,55m) (23,90m)
71' 2"
(20,69m)
82' 2 "
(25,06m)
86' 97'
53' 10-3/16" (x2)
(26,21m)
(29,56m) (16,45m x2)
Do not use impact gun for wall
screws.
Minimum torque force of 60 inch
pounds to maximum of 85 inch pounds.
Outside of pool
Inside of pool
Fold
Fold
BOLT
End
Start
NUT
Inside of pool
Outside of pool
!
IMPORTANT! Installing the wall joint in non-compliance with the specifications dictated by the manufacturer will void the warranty.
A
faulty installation will cause the wall/joint to split which could result in serious and/or fatal injuries!
Illustration 8.1