Model# ADF-150DX 40 Gallon DIRECTIONAL fish feeder SYSTEM Product Information Guide
INCLUDED PARTS 1) Hopper Assembly including Lid (3 Pieces) Poly Barrel Lid Poly Barrel Upper Poly Barrel Funnel 2) Directional Power Control Unit assembly and programming instructions for this unit are contained within its box (1 piece) 3) Leg Kit (15 pieces) Poly Barrel Leg/ Hardware/Bolt Kit PAge 2 Silicone Rubber Gasket (1 piece)
Poly Barrel Bolt Kit (1 Kit) 5/32” Nylon Lock Nut (7 pieces) 1⁄4” Nylon Lock Nut (10 pieces) REQUIRED TOOLS 5/32” Washer (7 pieces) 1⁄4” Washer (10 pieces) 1) Pliers 2) 1⁄4” Wrench 3) 5/32” Wrench 4) #8 Nut Driver (Hand held or for Cordless Drill) 5/32”x15/32” Bolt (7 pieces) 1⁄4” x 1” Bolt (10 pieces) Latch and striker 5) Cordless Drill – If Necessary Production Information Guide (1 Piece) Product Decal (1 Piece) Trophy Hunter Banner (Part#: RM-LABL-00040) Hinge with pole and cotter pin PAge 3
ASSEMBLY INSTRUCTIONS 1 Verify the contents of the package against the included parts list. If you are missing any parts from the list, please contact BA Products immediately at the toll-free number provided. 2 First, remove the lid and two hopper assembly pieces and then place the three pieces on the ground. 3 4 5 Second, remove both the power control unit box and the leg/bolt kit box. Open the leg kit box and locate the bolt kit and silicone rubber gasket.
7 Locate the hinge and install it with the rounded loops facing away from the feeder. Use the 5/32” x 15/32” Bolts and 5/32” Washers. Place the bolt head on top and the thread portion toward the bottom on the inside of the hopper. Install the 5/32” Nylon Lock Nuts and tighten securely (Illustration C). (Illustration C) (Illustration D) 8 Place the lid on top of the hopper unit and align the hinge knuckles on the lid between the knuckles on the metal hinge.
9 Close the lid and then locate the latch and striker. First, take the striker portion and install it onto the lid with the j-lip facing upward. These holes are already in place on the lid so install the 5/32” x 15/32” Bolts and the 5/32” Washers with the heads on the outside of the hopper and the threads facing into the hopper. Next, place the 5/32” Nylon Lock Nuts on the bolts and tighten securely. Locate the two (2) smooth marked spots on the hopper piece.
10 Once the hopper is assembled, make sure that the latch is closed and lay the hopper on its side. Next, locate the square tubing stub leg kit (3 pieces) and unwrap. Take one stub leg and locate the recessed cavities on the funnel portion of the hopper. Place the stub leg into any cavity so as it fits snug. Make sure that the stub leg is angled outward away from the hopper. Repeat this step for the remaining two stub legs.
14 With the hopper lying on its side, take one full extension leg section and slide it into the square stub leg that you have already installed on the hopper (Illustration J). 15 16 Repeat step #14 for the remaining two extension leg sections. Once all extension leg sections are installed into the stub legs, locate a second person to help raise the unit.
operating instructions Once a suitable, level location for the feeder is identified and the unit is properly erected, open lid and fill container with feed/seed to desired capacity, never to exceed 150 lbs. Once done, close the lid and lock the latch securely to insure it does not come off in the event of high winds, etc. This unit is designed to be used primarily with 1/4” or smaller fish food. This unit is not intended to be used with a wide variety of other type feeds.
BA Products is not responsible for damage, expense or injury caused by the unauthorized use of, alterations to, improper connection of and abuse or neglect of the BA Products’ feeder system. Never lean a ladder against the feeder when filling. You must always use an alternative method to fill your feeder. The use of a ladder, or some other similar type mechanism, leaning against the feeder is not recommended and strongly discouraged. This may result in damage to the unit or personal injury.
The AquaPro® Model #ADF-150 is loaded with features that you can not find anywhere else, such as a domed lid to effectively shed water, a built-in funnel to more efficiently focus feed to the power control unit, a unique low-profile design to protect against the feeder being top-heavy once filled, Polypropylene enforced construction for durability in the field, sturdy power coated leg kit, large lockable latch for your lid, not to mention all the features packed into the power control unit and timer.
BA Products 602 Fountain Parkway, Grand Prairie, Texas 75050 Telephone: (800) 847-8269. Fax: (972) 352-6633 www.aquaprofishfeeders.
