Specifications

ManualsBrandsAqua Systems ManualsHome building and DecorAQLP Series

This menu will appear only if Valve3 is configured for timeclock. The valve will rotate on and

off at the designated times. There is no manual override. If the Valve3 relay is on during the

programmed off time, it may be because of freeze protection.

Super Chlorinate

24 hours

Adjust Superchlorination period (1 - 96 hours)

Move to previous/next menu item

Larger pools or when you have an unusually high bather load, a large amount of rain, a

cloudy water condition, or any other condition that requires a large amount of chlorine to be

introduced to the pool, may require more hours of Superchlorination. Smaller pools require

less hours of Superchlorination.

Configuration Menu

The Aqua Logic MUST BE CONFIGURED before attempting to operate. Configuration information is

entered at the keypad and “tells” the Aqua Logic what equipment is connected and how each should be

controlled.

CAUTION: When changing an existing configuration, it is important to understand how

the pool system operates and what specific equipment is connected to each output. Incor-

rect settings in the configuration menu could lead to damaged equipment and improper

operation of the pool system.

Accessing the Configuration Menu

Configuring the Aqua Logic requires that you navigate through the Configuration Menu and input various

information. For more detailed information about using the Aqua Logic menu system, refer to the Opera-

tion Manual.

To access the Configuration Menu

Configuration

Menu-Unlocked

Configuration

Menu-Locked

Press repeatedly until “Configuration Menu” is displayed

Move to configuration menu items

Press BOTH buttons SIMULTANEOUSLY for 5 seconds to unlock

NOTE: The configuration menu automatically “locks” after 2 minutes of no buttons being

pressed to prevent unauthorized people from changing the control logic inadvertently and

possibly damaging the pool equipment or causing a “call back” to fix the configuration.

Quick “How To” Guide

Operate the Spa—Manually

1. Press the “Pool/Spa” button to go to “spa-only” operation (right LED illuminated). In some

cases, this may take more than one press of the button.

2. If the filter pump is not already on, press the “FILTER” button to turn it on.

3. If the spa is below the desired temperature, the heater will turn on automatically when the filter

pump is on and the valves are in the spa-only position. If you have not already set the desired

temperature for the spa, see “Set Heater Temperature” below

4. If the spa has a separate jet pump and or blower, determine if the jet pump/blower is con-

trolled by Aux1 or Aux2 (it should be marked on the label inside the door). Then press the

appropriate button to turn on the jets/blower.

Operate the Spa—Automatically

1. Press the “MENU” button repeatedly until “Timers Menu” is displayed

2. Press the “>” button repeatedly until the “Spa—all” or “Spa—wkend” is displayed.

3. Use the “+” and “-“ buttons to set the desired start time, then press “>” to switch to the off

time. Use the “+” and “-“ buttons to adjust the off time. If you are setting the “weekend”

timeclock, press “>” to go to the “weekday” settings.

Note: During the programmed spa time, the valves will automatically switch to the

“spa-only” position, the filter pump will turn on, and, if the spa is not up to the desired

temperature, the heater will start. This operation is the highest priority and will take

precedence over other automatically programmed operations. At the end of the spa

period, the Aqua Logic will return to its normally programmed operation state.

Set the Heater Temperature (or turn heater permanently off)

1. Press the “MENU” button repeatedly until “Settings Menu” is displayed

2. Press the “>” button repeatedly until the “Spa Heater1” or “Pool Heater1” is displayed.

3. Press the “+” or “-“ buttons repeatedly to adjust the temperature. If you adjust the tempera-

ture below 65ºF or above 104°F the display will indicate “off” and the heater will not operate

regardless of temperature.

Note: Separate temperatures for the pool and spa must be set. If the valves are in the

pool-only or spa spillover positions, then the heater will use the pool setting. If the

valves are in the spa-only position then the heater will operate according to the spa

setting.

Set the Chlorinator Output

1. Press the “MENU” button repeatedly until “Settings Menu” is displayed

2. Press the “>” button repeatedly until the “Spa Chlorinator” or “Pool Chlorinator” is displayed.

3. Press the “+” or “-“ buttons repeatedly to adjust the setting. If you adjust the setting to 0% the

chlorinator will be off all the time

Set Day and Time

Wednesday 10:37P

Adjust time setting

Move between start and stop times & to previous/next menu item

Valve3-all

8:30A to 4:00P

Adjust time s

Valve3-wkend

8:30A to 4:00P

Valve3-wkday

8:30A to 4:00P

Adjust time setting

Move between start and stop times & to previous/next menu item