Troubleshooting guide

12
OPERATING INSTRUCTIONS
CLEANING OR CHANGING THE FILTER BAG
NOTE: Make sure that the Power Supply is turned OFF and that your cleaner’s Floating Cable is unplugged from the Power
Supply before removing your cleaner from the pool.
1. With your cleaner on its back on a soft surface to avoid scratching it, use your thumbs to, push the Lock Tabs (located
on the sides of your cleaner’s underside) away from the center of the cleaner to unlock the Bottom Lid Assembly to release
the Bottom Lid Assembly that holds the Filter Bag.
2. Remove the Bottom Lid Assembly out from the body of your cleaner.
3. Remove Filter Bag Clips from each Wire Frame.
4. Remove the Filter Bag from the bag support Wire Frames.
5. Turn the Filter Bag inside out (the Fine Filter Bag has a soft felt-like surface on the inside), discard the large debris, and
wash off visible dirt using one of the following methods: (a) garden hose (b) Faucet. With any method gently agitate the
Bag in your hands to help remove tine particles while wringing, cleaning and squeezing the Bag gently until rinse water
is clear. Use of a washing machine (cold water, gentle cycle only) is recommended when visible dirt will not rinse off by
other methods. DO NOT USED DETERGENT or BLEACH! DO NOT MACHINE DRY!” to “a high pressure garden hose or
by dunking it in a clean bucket of water while gently agitating the Bag in your hands to help remove fine particles, and
wring the Bag until rinse water becomes clear. You may machine wash (Gentle Cycle / Cold Water ONLY) the Bag with NO
DETERGENT OR BLEACH. DO NOT iron or machine dry the Filter Bag.
6. Turn the Filter Bag “right side out” (felt-like surface on the inside), remount the Bag on the Wire Frames making sure
that the Label on the Bag is centered on either of the long sides of the Bottom Lid Assembly directly beneath one of the
Wire Frames.
7. At the top, pull, excess Bag toward the middle of each Wire Frame so that the Bag corners are snug against the corners
of the Wire Frame, bunch the excess Bag into the center area of the Wire Frames and pull the corners of the Filter Bag into
the Wire Frame corners by pulling the Filter Bag material from both sides towards the center of the Wire Frame.
8. Reinstall each Filter Bag Clips to hold the Filter Bag in place.
9. Re-install the Bottom Lid Assembly. Make sure that neither debris nor the Filter Bag itself interferes with complete
closure of the Bottom Lid Assembly. A locking sound from each Lock Tab will be heard when locked properly.
WHEN TO CLEAN FILTER BAG
It is suggested that you clean the Filter Bag after every use to ensure the strongest hydraulic drive and vacuum suction.
Your cleaner begins to slow down considerably, (constantly reverses direction before reaching portions of the pool it
would normally reach), it is sending a signal that it is time to clean the Filter Bag. Always thoroughly clean the Filter Bag
and rinse your cleaner and its components prior to storing it for any length of time.
REMOVING CLEANER FROM THE POOL
1. When your cleaner has completed its cleaning cycle it will automatically shut off. Turn off the Power Supply by pressing
the ON/OFF switch to the OFF position.
NOTE: A complete cycle is 2 hours, which is built-in to the Power Supply.
With your cleaner in the pool, gently pull it toward you using the Floating Cable. When your cleaner is within reach, reach
and grab its Handle firmly and remove it from the water using the Handle only. Rest the cleaner on its side to allow water
to drain from its body.
TIP: When resting your cleaner on its side, be sure to place it on a non-abrasive surface (i.e. Towel, doormat, etc.) to avoid
scuffing and scratching your cleaner.
IMPORTANT: Although a Filter Bag may appear clean it is capable of microfiltering out particulates 20 times smaller
than what the naked eye can see! It is crucial to thoroughly clean the Bag with each use to ensure its ability to
properly cover and clean your pool!
IMPORTANT: Using the Floating Cable to lift the cleaner out of the water will cause severe damage to your cleaner
and may result in costly repair!
IMPORTANT: Do not remove cleaner from pool for 20 minutes after cleaning cycle is complete to enable its motor to
properly cool and avoid costly motor damage!