DO NOT RETURN THIS PRODUCT TO RETAILER Return Merchandise Authorization Number (RMA#) is Required. To obtain RMA #, Technical Support or to review Troubleshooting Videos and Step-By-Step Troubleshooting Procedures please visit www.AquaProducts.com/Service. JET CLEANERS OPERATOR MANUAL AND TROUBLESHOOTING GUIDE Please Read Carefully Before Using Your Pool Cleaner This manual is for use with a variety of Aqua Products Robotic pool cleaners.
TABLE OF CONTENTS JET CLEANERS Table of Contents............................................................................................................................. 2 Introduction...................................................................................................................................... 3 How it Works.................................................................................................................................... 3 - 4 Operating Instructions.............
INTRODUCTION Dear Customer, Welcome to the family of Aqua Products and congratulations on purchasing the most reliable pool cleaner technology on the market today! Your new cleaner is a fully automatic, “robotic” mobile filtration system engineered with the patented SimplyReliable™ hydraulic jet drive propulsion system.
Complete Coverage: Like a car, your cleaner has two Axles; the front Axle turns your cleaner and the back axle is fixed. Your cleaner will operate using one of two turning systems. Turning Arc, cleaner moves to the left in an forwards curve Turning Arc, cleaner moves to the right in an forwards curve Rear Axle is fixed Rear Axle is fixed Locking Pin: The front Axle can slide all the way forwards and backwards in its slot.
Saving Your Wallet & The Planet Mobile Filtration System: Once the dirt is vacuumed into your cleaner’s body it is immediately trapped and filtered by its internal, reusable Filter Bag system, which traps the dirt and debris - so your pool filter system doesn’t have to work so hard. In essence, your cleaner is a mobile filtration system that works without hoses or costly, energy consuming main pool pumps or booster pumps.
OPERATING FEATURES Figure 1a BOTTOM LID ASSEMBLY 12 11 15 16 14 13 15 11 Figure 1b 12 21 15 13. 14. 15. 16. 18 11 Bottom Lid Wire Frame Bag Support “H” - Float Side Pocket Floats 11 17. 18. 19. 20. 15 20 Debris Intake Port Flap Filter Bag Square Floats Float Screws & Washers 17 19 21. Variable Port Depth Extensions 22. NeverStuck™ Rollers 23. Debris Intake Port Width Selector Figure 2 Cross-section of Pump Motor and Jet Valve Housing 24 24. 25. 26. 27. 28. 29. 30.
Important: Your cleaner may be of different shape or color and with features located in varying locations than those pictured in this operator manual. However, most of the operating functions are identical and therefore the following instructions should be reviewed thoroughly. Power Supply & Floating Cable Connections 1 Fig. 1 2 Power Supply (Transformer) with: • Built-in Forwards/Reverse Timer • Built-In 2-Hour Automatic Shut-Off 1. Power Supply 2. Power (ON/OFF) Switch 3. Socket (For Floating Cable) 4.
Cleaning Pattern / Directional Guidance Mechanism 8
OPERATING INSTRUCTIONS Never allow anyone to swim in the pool while the cleaner is in the pool! STEP 1 SETTING UP THE POWER SUPPLY 1. Place the Power Supply in a dry, sheltered area at least 12 feet / 4 meters away from the pool. Since the Power Supply is water resistant, not water proof, therefore should be placed in an elevated dry area where it will not be allowed to sit in puddles of water. 2.
SETTING A DIGITAL TIMER... Green LED Red “ON” LED Continuous Run (CRUN) button Digital timer display Up & Down arrow buttons RESET button Continuous Operation Press the C-RUN button, both the green LED above the C-RUN button and the Red “ON” LED will illuminate. The Cleaner will now clean your pool until you stop it by switching the Power Supply Switch to the “OFF” position.
KNOWING / USING MODEL FEATURES SETTING THE POWER SUPPLY TIMER (INTERNAL AND / OR EXTERNAL) If your cleaner has an adjustable Dial or Digital timer, you can set it for Continuous Run or Internal Timed Operation. All Power Supplies, including No Timer, Dial timer and Digital timer models, may be connected to an external, separately purchased timer, such as a house-type timer or pool control system.
OPERATING INSTRUCTIONS WHEN TO CLEAN FILTER BAG It is suggested that you clean the Filter Bag after every use to ensure the strongest hydraulic drive and vacuum suction. Your cleaner begins to slow down considerably, (constantly reverses direction before reaching portions of the pool it would normally reach), it is sending a signal that it is time to clean the Filter Bag. Always thoroughly clean the Filter Bag and rinse your cleaner and its components prior to storing it for any length of time.
TROUBLESHOOTING Should none of the troubleshooting procedures provided herein correct your specific issue, please visit our customer service department online at AquaProducts.com/Service to view troubleshooting videos and step-by-step procedures. Contact our customer service department toll free at 1-800-845-4856. Moves slowly or inefficient vacuuming • Check to see if the Filter Bag is thoroughly clean. FYI: The Fine Filter Bag is capable of filtering particles 20 times smaller than the naked eye can see.
TROUBLESHOOTING Reverses before reaching the opposite end of the pool • Turn the Time Control Dial (located on the Power Supply) clockwise a few degrees or adjust the digital timer using the “up” button to increase the time between reversals. Repeat if necessary. • Check to see if the Filter Bag is thoroughly clean and installed properly.
IMPORTANT: A Return Authorization Number (RMA) must be obtained from Aqua Products prior to shipping cleaner to its repair facility. Any item shipped to Aqua Products without a proper RMA number will be refused and returned! PREPARING YOUR CLEANER FOR SHIPPING In the event that you should have to send your cleaner in for repair, you must package the cleaner properly to ensure it reaches the repair facility safely and without incurring damage during transport.
Include a copy of all information obtained during your contact with the technical service analyst and / or Authorized Service Center, including your contact information and cleaner’s serial number in an envelope (Fig. 6c). A copy of the information relevant to the current technical issue should be sent in the packaging with your cleaner in an envelope.
DO NOT RETURN CLEANER TO RETAILER! If you have a technical service issue PLEASE REFER TO THIS MANUAL OR Contact Aqua Products for immediate support. Note that the absolute majority of technical issues can be resolved over the phone (1-800-845-485), by referring to this Operator manual or reviewing troubleshooting videos and information online anytime at www.AquaProducts.com/Service.
