DO NOT RETURN THIS PRODUCT TO RETAILER Return Merchandise Authorization Number (RMA#) is Required. To obtain RMA #, Technical Support or to review Troubleshooting Videos and Step-By-Step Troubleshooting Procedures please visit www.AquaProducts.com/Service. JET CLEANERS - IN GROUND OPERATOR’S MANUAL AND TROUBLESHOOTING GUIDE Please Read Carefully Before Using Your Pool Cleaner This manual is for use with a variety of Aqua Products Robotic pool cleaners.
TABLE OF CONTENTS JET CLEANERS Introduction ...................................................................................................................................... 2 Operating Features .......................................................................................................................... 3 Power Supply Units ......................................................................................................................... 4 Knowing / Using Model Features ............
OPERATING FEATURES This manual has been created to represent the set-up and troubleshooting practices required for a variety of Aqua Products cleaners. Although the shape, color and some components featured herein may not be identical to those of your cleaner, their operating and service procedures are. As there are a variety of features and components applicable to the various models produced, some pages may show these and may not be completely relevant to your model.
Important: Your cleaner may be of different shape or color and with features located in varying locations than those pictured in this operator manual. However, most of the operating functions are identical and therefore the following instructions should be reviewed thoroughly. POWER SUPPLY UNITS Figure 1 1 3 4 5 2 Fig. 1 Digital Power Supply (Transformer) with Two-Hour Automatic Shut-Off Fig. 2 Analog Power Supply (Transformer) with Two-Hour Automatic Shut-Off 1.1 1.2 1.3 1.4 1.5 2.
KNOWING / USING MODEL FEATURES SETTING THE POWER SUPPLY TIMER (INTERNAL AND / OR EXTERNAL) If your cleaner has an adjustable Dial or Digital timer, you can set it for Continuous Run or Internal Timed Operation. All Power Supplies, including No Timer, Dial timer and Digital timer models, may be connected to an external, separately purchased timer, such as a house-type timer or pool control system.
BOTTOM LID ASSEMBLY Figure 3 (Standard) 2 6 1 5 1 5 4 3 Next Generation Bottom Lid Assembly (Does not fit on all models) 2 11 5 3.1 3.2 3.3 3.4 1 Bottom Lid Wire Frame Bag Support “H” - Float Side Pocket Float 8 1 10 5 3.5 3.6 3.7 3.8 Debris Intake Port / Flap 17 Quart Filter Bag Square Floats Screw & Screw Float 7 9 3.9 3.10 3.
OPERATING INSTRUCTIONS Never operate your cleaner when it is not totally submersed in the pool water! Doing so may cause severe damage to motors and require costly repairs! STEP 1 SETTING UP THE POWER SUPPLY 1. Place the Power Supply in a dry, sheltered area at least 10 feet away from the pool. Since the Power Supply is water resistant, not water proof, it should not be left out in the rain or placed in puddles of water. 2. Plug the Power Supply Cord into a 115V, 3-prong grounded GFCI outlet.
SETTING THE DIGITAL TIMER PLEASE READ THE USER MANUAL FIRST Your Cleaner is equipped with a 90 second DIGITAL TIMER located on the Power Supply. To operate it please do the following: 1. Switch the Power Supply ON pressing the Power Switch to the ON position.. The display will FLASH two horizontal bars. 2. Observe the time required for the machine to move across the pool, at its widest point from one side to another.
SETTING THE “LOCK PIN” TO CHANGE THE CLEANING PATTERNS 1. Default Lock Pin setting. Your Jet cleaner will travel forward in a straight line, once the Auto Jet Propulsion system changes direction the Jet cleaner will reverse in a slight arc pattern and continue to repeat this cleaning pattern, systematically covering the entire pool floor. 2. Make sure the Lock Pin is securely positioned in the hole provided. 3.
CLEANER MAINTENANCE - CLEANING AND/OR CHANGING THE FILTER BAG NOTE: Make sure that the Power Supply is turned OFF and that the cleaner’s Floating Cable is unplugged from the Power Supply before removing your cleaner from the pool. 1. Place the cleaner on its back on a non-abrasive surface and release the two Lock Tabs on the underside of the cleaner. 2. Using your thumbs, push the Lock Tabs away from the center of the cleaner to unlock the Bottom Lid Assembly. 3.
TROUBLESHOOTING Should none of the troubleshooting procedures shown below correct your specific issue, please visit our customer service department online to view troubleshooting videos and step-by-step procedures.” If none of the detailed instructions and assistance offered online has helped, please feel welcome to contact our customer service department toll-free at 1-800-845-4856 for further assistance. contact our customer service department toll free at 1-800-845-4856.
MAKE A RECORD FOR FUTURE USE MODEL PURCHASE DATE PLACE PURCHASED SERIAL NUMBER NOTE: Serial number can be found on the warranty card, the packing carton and your cleaner. QUESTIONS? Contact the Retailer you purchased your cleaner from or visit the Manufacturer online at www.AquaProducts.com LIvE TECHNICAL SUPPORT (NORTH AMERICA) 1-800-845-4856 June - August 9:00am - 8:00pm (Mon. - Fri.) 9:00am - 1:00pm (Sat.) September - April 9:00am - 5:00pm (Mon. - Fri.
DO NOT RETURN CLEANER TO DEALER If you have a technical service issue PLEASE REFER TO THIS MANUAL OR CONTACT AQUA PRODUCTS to receive a Return Merchandise Authorization (RMA) number 1-800-845-4856 www.AquaProducts.
