User's Manual

1. Open the battery cap and
insert battery. Then, close
the battery cap.
2. Repeat the first step to
complete 4 transmitters
battery installation
Install transmitters by
1: Front-Left tire.
2: Front-Right tire.
3: Rear-Left tire.
4: Rear-Right tire.
APTOS DESIGN LAB
TPMS
External Tire Pressure Monitoring System
ADST002-R/ADST001-T
TPMS is composed of one receiver and 4 transmitters. Receiver receives information from
transmitters and update status to user. Transmitters integrated with sensors measure tire pressure,
temperature, and so on in real-time. Transmitters also transfer the information through the 434MHz
ISM band to the receiver
Description
► 433.92 MHz ISM band wireless communication.
► Real-Time pressure and temperature measurement.
► Real-Time update in the Receiver.
► Abnormal alarm to users.
► Voice reminder as well as LED indicators.
► Fully integrated car charger power I/F
Feature
Specification
Safety Precautions
Product Overview
Getting Started
Transmitter Receiver
Operating Temperature
Storage Temperture
Humidity
Carrier Frequency
Pressure Range
Temperature Range
Temperature Accuracy
Sampling Rate
Data Transfer Rate
Power
Power Comsuption
Battery Life
Weight
Dimension
LED Pressure Indicator
LED Status Indicator
Speech I/F
Centric Frequency
Storage Temperature
Operating Temperature
Power
Dimension
-30°C ~ +85°C
-30°C ~ +85°C
95%
433.92 MHz
100 ~ 900 Kpa
-30°C ~ +125°C
3°C
4 s
30 s
3.0 V Lithium
Max 13.5mA
1.5 years
14 g
22.5x22.5x25 (mm)
Red - Low Pressure Indicator
Blue - RX Indicator
Preload Coices for
Pressure Information
433.92 MHz
-30°C ~ +85°C
-30°C ~ +85°C
12V DC
74x30x22 (mm)
Transmitter Setup
Light Truck/LSUV/Sedan
Speaker
Low Pressure Indicator(Red)
Status Indicator(Blue)
Angle Adjustment
Extra Car Lighter
Power Plug
Reset Button
Receiver
Transmitter
Number for Tire Setup
Battery Cap
Jack for Air Gate
Receiver
First Time Usage
1. Please follow the step of transmitter setup to install 4 transmitter batteries. While installation is
completed, please keep transmitters close to the receiver.
2. Please follow the step of receiver setup to power on Receiver.
3. After powering on the receiver and 4 transmitters, the receiver will automatically search 4
transmitters. (Each transmitter is given a unique ID.)
4. If transmitter is searched, the corresponding LEDs will be turned on.
5. While 4 transmitters are recognized, the receiver will turn on all LEDs, including 4 RED LED for
each transmitter alarm as well as 1 BLUE LED for receiving indication.
6. Install transmitters to each tire by following the step of transmitter setup. Then, remove the
receiver from car lighter hole and re-plug in the receiver to the car lighter hole to reset the
receiver.
After plug in the car lighter,
the receiver automatically start
gathering the information from
four transmitters.
Plug the receiver into car lighter.
Lighter Jack
TPMS Usage
1. Please follow the step of thansmitter setup to install the four tansmitter on the tire.
2. No need to remove the transmitters if there is no abrupt situation.
Note: Please take off the battery while tansmitter is removed from tire. Or, the tansmitter would keep
consuming the power from battery.
Transmitter
Power On Receiver
Normal Situation
Abnormal Situation
1. Power on the receiver by the step of transmitter setup. Then 4 RED LED will be blinking for a while.
2. While the 4 RED LED is turned off, the receiver starts to receive the real-time information from
transmitters.
3. If there is any received information from transmitters, then the BLUE LED of the receiver is blinking.
● Light Truck/LSUV - The abnormal situation means the tire pressure is less than 48 PSI. And, RED
LED on the receiver will be turned on. Meanwhile, the receiver will speak out
the tire position as well as its pressure.
● Sedan - The abnormal situation means the tire pressure is less than 26 PSI. And, RED
LED on the receiver will be turned on. Meanwhile, the receiver will speak out
the tire position as well as its pressure.
● Light Truck/LSUV - If tire pressure is between 54 ~ 48 PSI, RED LED is blinking.
● Sedan - If tire pressure is between 30 – 26 PSI, RED LED is blinking.
● Light Truck/LSUV - The normal situation means the tire pressure is greater than 54 PSI.
● Sedan - The normal situation means the tire pressure is greater than 30 PSI.
Front-Right TireFront-Left Tire
Status
Rear-Right TireRear-Left Tire
Remove valve cap of tire
Package List
1. Receiver x 1
2. Transmitter x 4
3. User manual x 1
Please follow the safety precautions carefully before you use the product. Make sure that you use the
product correctly according to the procedures described in the guide.
1. Never place the product close to equipment generating strong electromagnetic fields.
* Exposure to strong magnetic fields may cause malfunctions.
2. Never plug or unplug the product if your hands are wet, otherwise it will may cause electrical shock.
3. Do not drop the product to the ground to avoid malfunction.
4. Do not attempt to disassemble or alter any part of the product that is not described in this guide.
5. Do not put heavy material on the product.
6. Do not use the product in a wet location.
* In the event that water or other liquids enter the interior, immediately unplug the product from the
computer.
* When continuing usage of the product under above situation may cause fire or electric shock.
7. Do not place the product near a heat source or expose them to direct flame or heat.
8. Do not place the product in damp or dusty places.
Description
Front-Left
Front-Right
Rear-Left
Rear-Right
Indication on Receiver
FL
FR
RL
RR
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
● Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Federal Communication Commission
Interference Statement