Apriva BT200-T Smart Card Reader for Window Mobile Version 6.
Apriva BT200-T Smart Card Reader for Windows Mobile Version 6.
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide Notice Terms and Conditions This publication is proprietary of Apriva and is intended solely for use by Apriva customers. This publication may not be reproduced or distributed for any purpose without the written permission of Apriva. The information Apriva furnished in this publication is believed to be accurate and reliable.
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide IF YOU DO NOT AGREE TO THE ENCLOSED TERMS AND CONDITIONS, PROMPTLY RETURN THE PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND. ALL RETURNED PRODUCTS MUST BE IN NEW CONDITION, IN THE ORIGINAL PACKAGING.
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide Contents Introduction .........................................................................................................1 Definitions .............................................................................................................1 Hardware and Software Requirements .................................................................2 Hardware Required ...........................................
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide Figures Figure 1 – Apriva Reader features ........................................................................3 Figure 2 – Apriva Reader driver and firmware files ...............................................5 Figure 3 – Reader Connection area ......................................................................6 Figure 4 – Battery Level area ...............................................................
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide Introduction This guide provides instructions to install and operate the Apriva® BT200-T Smart Card Reader on mobile devices that use the Windows Mobile® version 6.x operating system. (Windows Mobile version 6.5 is currently not supported.) NOTICE For wireless connections, mobile devices must support Bluetooth® stack requirements. For more information, contact Apriva Technical Support.
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide Hardware and Software Requirements The following sections describe hardware and software requirements.
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide Apriva BT200-T Reader The Apriva BT200-T Reader uses a hardware security module with embedded public key infrastructure (PKI) information to create a secure, one-to-one connection with the mobile device through wireless Bluetooth protocol or a Universal Serial Bus (USB) connection. Apriva Reader Features Figure 1 shows the following Apriva Reader features: • ON/OFF button: Powers the reader on and off.
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide Powering on the Reader When powered on, both LEDs illuminate while the reader performs a series of startup tests. For LED startup descriptions, see Reader LED Startup Indications on page 14. To power the reader on or off: Press the Power On/Off button on the top of the reader.
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide Figure 2 – Apriva Reader driver and firmware files 6. Select the AprivaSmartCardDriver file shown in the directory. Selecting the file automatically installs it. After installation, the mobile device restarts. © Copyright 2010 Apriva.
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide Pairing the Devices Pairing the reader (and smart card) to the mobile device creates a one-to-one connection between the devices. To pair with the reader to the mobile device: 1. Connect the USB cable to the PDA port on the reader, and then connect the other end of the USB cable to the mobile device. Use the supplied USB adapter if necessary. 2. Press the ON/OFF switch to power on the reader. 3.
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide • If the test is successful, the reader is now paired for wireless operation. When the reader is powered on and the smart card is inserted, the reader is available for Bluetooth operation. When the smart card is removed or when you power it off, radio frequency (RF) emissions stop and the reader is disabled.
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide Using Tethered USB Mode You can disable Bluetooth (wireless) mode and use the reader in tethered USB mode. Tethered USB mode prevents wireless RF emissions. This is useful in situations where RF emissions are not allowed, such as airplanes or Sensitive Compartmented Information Facilities (SCIFs). NOTE: The devices must be paired before you can switch between USB and Bluetooth modes.
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide Charging the Reader Battery The reader battery must be fully charged before use. It takes approximately three hours to charge a completely discharged battery. The LEDs on the top of the reader indicate the charge status. See Charging Indications on page 10. NOTICE If you are charging the battery with a computer that uses Windows XP, you must first install the Apriva USB driver.
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide To charge the reader battery: Connect the USB cable from the PC/CHARGE port on the reader to the USB port on the computer or a standard wall charger. Allow the battery to charge for 20 to 30 minutes. When charging, the GREEN LED is continuously lit with occasional quick flashes. Charging Indications Table 2 shows reader LED charging indications.
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide Setting the Reader Power Down Timers You can set the amount time that elapses before the reader powers down when it is inactive. You can set the timers for when the reader has no smart card inserted (No Card) or when the smart card is inserted (Card Present). To change the Power Down Timer settings: 1. From the mobile device applications menu, select the Apriva Reader icon ( ).
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide Viewing Reader Details The Details tab shows the following: • Reader Info: Shows reader copyright, version, and serial number. • Reader Diagnostics: Shows reader diagnostic results. If any of the diagnostics results show “Fail,” contact Apriva Technical Support for assistance. See Apriva Technical Support on page 17. • Reader Firmware Signature: Shows the reader firmware signatures.
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide Viewing Reader Versions The Version tab shows the driver and reader version information. Viewing Reader Information To view reader information: 1. From the mobile device applications menu, select the Apriva Reader icon ( ). The Apriva Smart Card Reader screen appears. 2. Select the Version tab to view version information. See Figure 7.
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide Reader Troubleshooting Tips The following sections describe general reader troubleshooting tips. Reader LED Startup Indications When you power on the reader, the LEDs remain lit for a few seconds while the reader performs an integrity check.
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide Reader LED Descriptions Table 3 describes reader LED indications and their meanings. Action Reader powered on using power button Battery test mode (about four seconds) Reader ready mode Indication Meaning Solid GREEN and Normal power on indication while reader solid RED for about completes self test. two seconds Solid GREEN Battery over 75% charged, ready for reader operations.
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide Reader Error Messages Table 4 provides information to help you troubleshoot reader errors and error messages. For errors not defined here or for additional support, contact Apriva Technical Support. See Apriva Technical Support on page 17. Error Message Possible Solution The CardReader was not found. Check the reader connection and make sure the reader is powered on.
Apriva® BT200-T Smart Card Reader for Windows Mobile® Version 6.x Installation and User’s Guide Support The following sections provide support information. Apriva Technical Support The Apriva Technical Support Department is available 24 hour a day, 7 days a week including holidays.
Apriva 6900 East Camelback Road Suite 700 Scottsdale, Arizona 85251 U.S.A. www.apriva.com © 2010 Apriva All rights reserved.
