Apriva BT200-T Smart Card Reader for Intermec CK61B/G ® ® Installation and User’s Guide Apriva 6900 East Camelback Road Suite 700 | Scottsdale AZ 85251
Apriva BT200-T Smart Card Reader for Intermec CK61B/G Installation and User’s Guide ® ® Part number 700013-01 September 2010 Apriva 6900 East Camelback Road Suite 700 | Scottsdale AZ 85251
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Notice Terms and Conditions This publication is proprietary of Apriva and is intended solely for use by Apriva customers. This publication may not be reproduced or distributed for any purpose without the written permission of Apriva. The information Apriva furnished in this publication is believed to be accurate and reliable.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide IF YOU DO NOT AGREE TO THE ENCLOSED TERMS AND CONDITIONS, PROMPTLY RETURN THE PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND. ALL RETURNED PRODUCTS MUST BE IN NEW CONDITION, IN THE ORIGINAL PACKAGING.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Contents Introduction .........................................................................................................1 Definitions .............................................................................................................1 Hardware and Software Requirements .................................................................2 Hardware Required .....................................................
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Adding the ID Certificate ...............................................................................21 Adding the Key Certificate ............................................................................22 Adding the Sign Certificate ...........................................................................22 Adding a Soft-Token Certificate ....................................................................
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Figures Figure 1 – Apriva Reader features ........................................................................3 Figure 2 – Apriva Reader driver and firmware files ...............................................5 Figure 3 – Intermec Version Information screen ...................................................6 Figure 4 – Reader Connection area ......................................................................
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Introduction This guide provides instructions to install and operate the Apriva® BT200-T Smart Card Reader and related Apriva security applications on an Intermec® CK61B/G mobile device. The Apriva products covered in this guide provide one-to-one login access and secure, encrypted data features.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Hardware and Software Requirements The following sections describe hardware and software requirements.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Apriva BT200-T Reader The Apriva BT200-T Reader uses a hardware security module with embedded public key infrastructure (PKI) information to create a secure, one-to-one connection with the mobile device through wireless Bluetooth protocol or a Universal Serial Bus (USB) connection. Apriva Reader Features Figure 1 shows the following Apriva Reader features: • ON/OFF button: Powers the reader on and off.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Powering on the Reader When powered on, both LEDs illuminate while the reader performs a series of startup tests. For LED startup descriptions, see Reader LED Startup Indications on page 15. To power the reader on or off: Press the Power On/Off button on the top of the reader.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide 4. Copy and paste the Apriva reader firmware and driver files from the computer to the following directory of the mobile device: Start > File Explorer > My Documents, as shown in Figure 2. The Apriva Reader file names are similar to the following: • AprivaReader.bin, where “” is the version number. • AprivaSmartCardDriver..cab, where “” is the version number.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Checking the Intermec SSPD and Firmware Versions Before you pair the reader to the mobile device, make sure the Intermec firmware and SmartSystems Platform Bundle (SSPD) are the latest versions available. This ensures that the mobile device firmware is compatible with the Apriva Reader driver. To view the Intermec SSPD and firmware versions: 1. Select Start > Internet® Explorer®. 2.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Pairing the Devices Pairing the reader (and smart card) to the mobile device creates a one-to-one connection between the devices. To pair with the reader to the mobile device: 1. Connect the USB cable to the PDA port on the reader, and then connect the other end of the USB cable to the mobile device. Use the supplied USB adapter if necessary. 2. Press the ON/OFF switch to power on the reader. 3.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide • If the test is successful, the reader is now paired for wireless operation. When the reader is powered on and the smart card is inserted, the reader is available for Bluetooth operation. When the smart card is removed or when you power it off, radio frequency (RF) emissions stop and the reader is disabled.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Using Tethered USB Mode You can disable Bluetooth (wireless) mode and use the reader in tethered USB mode. Tethered USB mode prevents wireless RF emissions. This is useful in situations where RF emissions are not allowed, such as airplanes or Sensitive Compartmented Information Facilities (SCIFs). NOTE: The devices must be paired before you can switch between USB and Bluetooth modes. See Pairing the Devices on page 7.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Charging the Reader Battery The reader battery must be fully charged before use. It takes approximately three hours to charge a completely discharged battery. The LEDs on the top of the reader indicate the charge status. See Charging Indications on page 11. NOTICE If you are charging the battery with a computer that uses Windows XP, you must first install the Apriva USB driver.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide To charge the reader battery: Connect the USB cable from the PC/CHARGE port on the reader to the USB port on the computer or a standard wall charger. Allow the battery to charge for 20 to 30 minutes. When charging, the GREEN LED is continuously lit with occasional quick flashes. Charging Indications Table 2 shows reader LED charging indications.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Setting the Reader Power Down Timers You can set the amount time that elapses before the reader powers down when it is inactive. You can set the timers for when the reader has no smart card inserted (No Card) or when the smart card is inserted (Card Present). To change the Power Down Timer settings: 1. From the mobile device applications menu, select the Apriva Reader icon ( ). The Apriva Smart Card Reader screen appears.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Viewing Reader Details The Details tab shows the following: • Reader Info: Shows reader copyright, version, and serial number. • Reader Diagnostics: Shows reader diagnostic results. If any of the diagnostics results show “Fail,” contact Apriva Technical Support for assistance. See Apriva Technical Support on page 29. • Reader Firmware Signature: Shows the reader firmware signatures. To view reader information: 1.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Viewing Reader Versions The Version tab shows the driver and reader version information. Viewing Reader Information To view reader information: 1. From the mobile device applications menu, select the Apriva Reader icon ( ). The Apriva Smart Card Reader screen appears. 2. Select the Version tab to view version information. See Figure 8.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Reader Troubleshooting Tips The following sections describe general reader troubleshooting tips. Reader LED Startup Indications When you power on the reader, the LEDs remain lit for a few seconds while the reader performs an integrity check.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Reader LED Descriptions Table 3 describes reader LED indications and their meanings. Action Reader powered on using power button Battery test mode (about four seconds) Reader ready mode Indication Meaning Solid GREEN and Normal power on indication while reader solid RED for about completes self test. two seconds Solid GREEN Battery over 75% charged, ready for reader operations.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Reader Error Messages Table 4 provides information to help you troubleshoot reader errors and error messages. For errors not defined here or for additional support, contact Apriva Technical Support. See Apriva Technical Support on page 29. Error Message Possible Solution The CardReader was not found. Check the reader connection and make sure the reader is powered on.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Apriva CSPware You can use Apriva® CSPware to manage hard-token (smart card) and softtoken (PKCS#12) device certificates on the mobile device. This allows you to access the Microsoft Certificate Store and use certificate interaction for secure features such as connecting to secure websites.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide 5. Right-click on the latest version of the AprivaCSPwareVxx-xxxx.zip file (where is the version number), and then select Download from the menu. See Figure 11. Figure 11 – Download option 6. Save the Zip file in the folder that you created in step 2. 7. Unzip (extract) the Zip file in the folder. 8. Open the unzipped folder, and then open the Pocket PC folder.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Installing the CSPware Software on the Mobile Device To install the CSPware software on the mobile device: 1. If you do not have one currently installed, download a data synchronization program, such as Microsoft ActiveSync (for Windows XP) or Windows Mobile Device Center (for Windows Vista or Windows 7). You can download the programs from the Microsoft website at: http://www.microsoft.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Adding and Viewing Certificates You can add hard-token or soft-token certificates to the mobile device. Adding the ID Certificate The ID certificate contains your personal information. To add the smart card ID certificate to the mobile device: 1. From the mobile device applications menu, select Apriva CSP. The Apriva CSP Certificates screen appears. See Figure 12. Figure 12 – Apriva CSP Certificates screen 2.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Figure 13 – Registering certificate message Adding the Key Certificate Key certificates are PKI certificates issued by a certificate authority (CA). To add the smart card Key certificate to the mobile device: 1. From the mobile device applications menu, select Apriva CSP. The Apriva CSP Certificates screen appears, as shown in Figure 12 on page 21. 2. Select Add Key Certificate.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Adding a Soft-Token Certificate If you are using a soft-token (PKCS#12) certificate instead of a smart card, you can add the soft-token certificate to the mobile device. To add a soft-token certificate to the mobile device: 1. If applicable, copy and paste the certificate to the mobile device. See Installing the CSPware Software on the Mobile Device on page 20. 2.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Viewing All Certificates You can view all certificates stored on the mobile device. To view all certificates on the mobile device: 1. From the mobile device applications menu, select Apriva CSP. The Apriva CSP Certificates screen appears, as shown in Figure 12 on page 21. 2. Select View All Certificates. All installed certificates are displayed. See Figure 15.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Apriva Guard Apriva® Guard provides a secure login connection between Apriva products that use public key infrastructure (PKI) certificates and mobile devices that use the Windows® Mobile® operating system. Apriva Guard ensures secure access by requiring you to log in to the mobile device with your personal identification number (PIN).
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide 3. Double-click the SensaGuard.Release folder, and then double-click the Windows Mobile folder to view the available Apriva Guard download files. The version release dates are shown under the “Time” column. See Figure 17. Release dates Figure 17 – Apriva Guard files 4. Right-click on the latest version of the AprivaGuard.SWM5PPC.xx.xx.xx.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Installing the Apriva Guard Software on the Mobile Device To install the Apriva Guard software on the mobile device: 1. If you do not have one currently installed, download a data synchronization program, such as Microsoft ActiveSync (for Windows XP) or Windows Mobile Device Center (for Windows Vista or Windows 7). You can download the programs from the Microsoft website at: http://www.microsoft.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Apriva Vault Apriva® Vault works with user authentication software, such as Apriva Guard, to create a secure partition on mobile devices that use the Windows® Mobile® operating system. Apriva Vault uses Advanced Encryption Standard (AES) 256 data-at-rest storage. You can store files and folders in the secure partition, as shown in Figure 20.
Apriva® BT200-T Smart Card Reader for Intermec® CK61B/G Installation and User’s Guide Support The following sections provide support information. Apriva Technical Support The Apriva Technical Support Department is available 24 hour a day, 7 days a week including holidays.
Apriva 6900 East Camelback Road Suite 700 Scottsdale, Arizona 85251 U.S.A. www.apriva.com © 2010 Apriva All rights reserved.
