User's Manual
Table Of Contents
- UA-612 Installation Sheet V1.2
- Reader Description
- Parts List
- Installation Procedure
- Product Specifications
- Cable to Controller and Power Supply
- Reading Distance
- Notes
- 1. Connect the black wire (negative) first, and the red wire (positive) last. Disconnect power before any wiring changes.
- 2. The LED and Beeper lines are logic levels. Never apply power to them. They may be pulled to a low level (0 to 1.2 VDC) to enable their functions, and left floating or pulled to a high level (3.6 to 5.0 VDC) when not used.
- 3. UA-612 readers have both Wiegand-protocol and RS-232 serial interfaces. For information on RS-232, contact AWID’s technical support.
- 4. For additional information, please visit AWID’s Web site www.awid.com. For technical support questions visit www.awid.com/support or call 1-800-369-5533 (in the U.S.) or 1-408-825-1100 from 8:00 a.m. to 5:00 p.m. Pacific Time.
- 5. FCC Compliance: This equipment has been tested and found to be in compliance with the limits for FCC part 15, Class A digital device. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instruction manual, may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
- The users are prohibited from making any change or modification to this product. Any modification to this product shall void the user’s authority to operate under FCC Part 15 Subpart A Section 15.21 regulations.
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- UserManual
MPR-2010-2.7E4-CN Page 9 7/22/2008
4 INSTALLATION PROCEDURE
This section provides information on installation and operation of MPR-2010-2.7E45V-CN
readers.
4.1 PARTS LIST
Verify that all items listed below are present before starting the installation.
4.1.1 BR
a. Sentinel-Sense MPR-2010-2.7E4-CN BR (FW version 2.xxMf) Qty=1
b. Documentation and Demo Program CD Qty=1
c. Power supply – PS92A-0-0, 50-60 Hz and 110 to 220 VA Qty=1
d. Reader mounting bracket – MPR-2010MB (Optional) Qty=1
e. External/Secondary Antenna – MPR-2012ANT (Optional) Qty=1
4.1.2 BN
a. Sentinel-Sense MPR-2010-2.7E4-CN BN (FW version 2.xxNf) Qty=1
b. Documentation and Demo Program CD Qty=1
c. Power Injector-Power Supply unit – PIPS48-0.3A Qty=1
d. Reader mounting bracket – MPR-2010MB (Optional) Qty=1
e. External/Secondary Antenna – MPR-2012ANT (Optional) Qty=1
4.1.3 LR-911
a. Sentinel-Prox LR-911 Reader Qty=1
b. Installation Instructions (packed inside Reader carton) Qty=1
(Tags for the LR-911 Reader and Installation Kit are available separately)
4.2 PREPARATION FOR INSTALLATION
4.2.1 Bench Top Verification
It is always a good idea to verify system operation before committing to a full-scale
installation. The following are the necessary steps to test the reader’s operation in a
static environment.
BR
Connect BR to the RS-232 port of a PC
Connect the power jack from the wall plug power supply to MPR-2010BR.
BN
Connect the RJ-45 cable between the reader and connector labeled “Out” on the
PIPS48-0.3A, connect from Ethernet Hub/Switch to where “In” is labeled. Plug in
power.