DC-1023 -1- 8/6/2010 SENTINEL-PROX DC-1023 Dual frequencies RFID Reader Users Manual-041419 Your best option for Proximity Access Control
DC-1023 -2- 8/6/2010 C OPYRIGHT ACKNOWLEDGEMENTS The contents of this document are the property of Applied Wireless Identifications Group, Inc. (AWID) and are copyrighted. All rights reserved. Any reproduction, in whole or in part, is strictly prohibited. For additional copies of this document please contact: AWID 18300 Sutter Blvd Morgan Hill, CA 95037 http://www.AWID.
DC-1023 -3- 8/6/2010 Table of Contents REVISION HISTORY .........................................................................................................4 1 INTRODUCTION.........................................................................................................5 1.1 1.2 1.3 2 SPECIFICATIONS ......................................................................................................5 2.1 3 Measuring Read Distance .........................................................
DC-1023 -4- 8/6/2010 REVISION HISTORY Version No. 1.0 Revised By Z.
DC-1023 1 -5- 8/6/2010 INTRODUCTION AWID's Sentinel-Prox DC-1023 Reader is a dual frequencies versatile smart card/smart label and proximity card reader for switch plate mounting. This Reader will provide simultaneous Wiegand and RS-232 output formats. Its primary applications are Access Control and Time & Attendance applications. 1.1 o o o o 1.
DC-1023 -6- 8/6/2010 to the Reader, until a BEEP occurs. The BEEP indicates that the Reader detects and read the card. In order to read again, the card must be fully withdrawn from the Reader’s field of surveillance and then re-approached again. During normal operation, the card can be presented at any angle relative to the Reader, however this will result in slight variation of read range. Note: Do not "wave" the card in front of the Reader.
DC-1023 3.4 -7- 8/6/2010 GENERAL WIRING REQUIREMENTS All the Reader wiring must be continuously shielded. AWID recommends using #22 AWG up to #18 AWG, six or seven-conductor shielded cables. Longer distances and higher current consumption on the power supply line will require larger gauge wires. Refer to Table 1 and Figure 1, Figure 2 and Figure 3 on the following pages to determine your data lines’ wiring requirement.
DC-1023 -8- Figure 1 Figure 2 8/6/2010 Wiring Diagram for Wiegand Output Format Wiring Diagram for RS232 Output Format Your best option for Proximity Access Control
DC-1023 -9- Figure 3 8/6/2010 Wiring Diagram for Wiegand & RS232 Output Format 4 INSTALLATION PROCEDURE Check to verify that every item listed under Section 5.1 of this manual is present before starting the installation. 4.1 PARTS LIST a. Installation sheet, P/N: xxx-xx-x b. Sentinel-Prox DC-1023 Reader, P/N: xxx-xx-x c.
DC-1023 - 10 - 8/6/2010 4.2 INSTALLATION STEPS 1. Prepare the single-gang electrical wiring box for Reader mounting. Observe ADA requirements. 2. If double-gang electrical box is used, drill through the four blind mounting holes on the four corners of the Reader. 3. Guide the open end of the Panel’s control cable through the access hole on the electrical junction box. Secure the cable by tightening the cable clamp. 4. Remove the Snap-On cover of the Reader (item b of the parts list) 5.
DC-1023 - 11 - 8/6/2010 When obtaining a RMA number for RFID tags, please provide AWID Customer Service Department with the serial numbers, card identification numbers, facility codes and etc. If exact duplicates of returned cards or tags are requested, the customer must provide AWID with the numbers needed. AWID reserves the option to replace or repair returned merchandise. Items returned to AWID without the proper authorization will be returned to the originators at their own expense.
DC-1023 - 12 - 8/6/2010 For additional information, please visit AWID’s Web site www.awid.com. For technical support questions, visit www.awid.com/support, or call +1-408-825-1100 from 8:00 a.m. to 5:00 p.m. Pacific Time (GMT - 8 hrs). 8 Patents and Approvals AWID products are covered by United States patent #5594384. AWID logo is a registered trademark of Applied Wireless Identifications Group, Inc. Where required, AWID’s products are approved by the appropriate regulatory agencies: U. S.
