User Guide

ManualsBrandsApplied Energy ManualsOtherSELECTRONIC PREMIER

Warmer

Cooler

Start/Stop

Temperature

Lock

Selectronic

Premier

Selectronic

Premier

IMPORTANT

This booklet should be given to the customer

after installation and demonstration

After Sales Service

We offer a technical advisory service on the telephone to installers and other customers with problems

in the field.

RING 0844 372 7766 (UK ONLY)

Remember to quote type of shower, as written on the front of the shower and on this leaflet.

The model and serial number are located on the bottom face of the shower.

Make a note of those numbers here, and be sure to quote them if you call for advice.

Model Number: 53--__________________ / Serial Number:____________________

Note: You may be charged for a service call if you do not have the serial number.

Full details of terms and conditions are available on request from:-

Applied Energy Product Ltd, Morley Way, Peterborough, PE2 9JJ

Website: www.redring.co.uk

Thermostatic Instantaneous Electronic Shower

Handbook

A3:567-2300-03 A

01-10-2010

We, Applied Energy Products Ltd., guarantee this product for domestic use only, for the period of 36

months from the date of purchase.

Within the guarantee period we will resolve, free of charge, any manufacturing defects in the product

resulting from faulty workmanship or material on the condition that:

A) The appliance has been correctly installed in accordance with our instructions and is being used on the supply

circuit or voltage printed on the rating plate.

B) The appliance has been used in accordance with these instructions and has not been tampered with or

otherwise subject to misuse, neglect or accident.

C) The appliance has not been taken apart, modified or repaired except by a person authorised by us.

D) Evidence of the date of purchase in the form of an invoice or receipt will be required in order to qualify for an

in-guarantee repair.

E) The guarantee period for the products used in commercial applications will be limited to 12 months.

F) For the service work to be undertaken free of charge, the work must be only undertaken by

Applied Energy Products Limited, or our approved agents.

G) Service under guarantee has no effect on the expiry date. The guarantee on any exchanged parts or product

ends when the original guarantee period ends.

EXCLUSIONS

This guarantee DOES NOT cover damage or defects arising from poor or incorrect installation, improper use or lack of maintenance,

including build-up of limescale. It is the responsibility of the installer to check that the installation parameters meet the requirements

of the product, and any relevant regulations.

If we are called out to a fault, which is subsequently identified as being an installation fault, we will make a charge. It is important

that the routine checks are completed before calling us out, as many issues can be simply diagnosed and resolved.

We make no guarantees as to response times for repairs. We will endeavour to achieve the most timely response possible but while

we indicate an average response time, this should not be taken as a guarantee.

The guarantee applies to a repair or replacement (at our discretion) of the product subject to the conditions above, and DOES NOT

cover compensation for the loss of the product or consequential loss of any kind

The guarantee does not apply to the repair or replacement of pressure relief devices, sprayheads, hoses, accessories, isolating

switches, electrical cable, fuses and/or circuit breakers.

This guarantee does not affect your statuary rights.

GUARANTEE

Terms and Conditions for UK (outside UK contact your local distributor)

Summary of content (12 pages)

PAGE 1
I GUARANTEE I Selectronic Premier Terms and Conditions for UK (outside UK contact your local distributor) We, Applied Energy Products Ltd., guarantee this product for domestic use only, for the period of 36 months from the date of purchase.
PAGE 2
Contents Selectronic Premier Selectronic Premier Plus (with 1.
PAGE 3
Remove the four cover screws and lift the cover off. Typical guideline dimensions used for less- abled bathroom installations Remove the four inlet cover screws and remove inlet cover - also the two side access trimplate section screws and remove complete with seal. C Plumbing to be carried out before wiring Diagram 2 DO NOT use jointing compounds on any pipe fittings for the installation.
PAGE 4
The Inlet fitting is designed to rotate through 180° to allow for either Top or Bottom/Rear entry fitting (See Diagrams 3). Installation Note: The inlet fitting is designed to enter a compression fitting only. DO NOT use push Fit connectors as full engagement cannot be guaranteed. DO NOT use excessive force when making these connections. Installation Note: If installing a water feed pipe from the back, the use of a soldered Elbow Connector is recommended.
PAGE 5
entry points then the following backplate component will need to be discarded allowing for the conduit to fit into the backplate. See Diagram 5 - Option ‘E’ or ‘F’. Diagram 5 IMPORTANT Connect flying lead from PCB to rear of the front cover - see Diagram 6. E FIT EARTHING SLEEVE Diagram 7 Replace the front cover and fasten in position with four screws. NEUTRAL EARTH LIVE CIRCUIT PROTECTION Unit Rating MCB 8.5kW 40A I I I 9.5kW 40/45A 45A I I I 10.
PAGE 6
The second set of 3 mounted directly below are ‘Shower Control Feature Setting Options’ and can be set to suit the requirements of user.
PAGE 7
How To Use Your Shower temperature). I Your shower has four modes of operation, Normal and three Temperature Lock postions 1, 2 and 3. (Please see Changing the Operating Mode Templock/Normal section on Page 9) The Temperature Lock feature ensures a preset maximum temperature is not exceeded. The shower is factory preset at Locked Position 1 (40°C maximum - temperature range 34 - 40°C). This can be changed on installation / commissioning for any of the other three options.
PAGE 8
Over Temperature Shutdown Diagram 18 If an abnormal condition occurs which causes the water to get too hot. bleep several times and the display will change to “t” (See Diagram 21). Diagram 22 In order to stop the shower automatically switching off, press either the warmer or cooler button. The unit will automatically shutdown straight away and the water will stop flowing. This is to prevent any hot water coming out of the handset.
PAGE 9
DIP SWITCH TERMINAL BLOCK WARNING THIS PRODUCT MUST BE EARTHED TEMPLOCK SWITCH LOGIC PCB THERMAL CUTOUT WARNING HEAT EXCHANGER PRESSURE RELIEF VALVE ENSURE POWER IS OFF BEFORE REMOVING COVER. REPLACE THIS COVER PRIOR TO FRFITTING THE FRONT COVER. 5. A stabiliser is built into the flow valve to automatically compensate for small fluctuations in water pressure that frequently occur in households.
PAGE 10
Warning! Make sure that you avoid hidden cables and pipes when drilling holes in the wall. Diagram 27 Battery Replacement Diagram 30 Battery replacement is required when the Red light confirmation signal fails to illuminate, hence, no signal communication with the shower. Battery life expectation is purely governed by the overall shower use – when using the remote control. Place the docking station on the wall and mark the position of the fixing holes. Drill (Ø6 mm) and plug.
PAGE 11
Periodical Maintenance 360° FULL CIRCLE Diagram 33 Cleaning the Filter It is recommended that the filter is periodically cleaned in order to maintain the performance of the shower. It is essential that this operation is carried out by a competent person. FRESH ECSTASY (Single Inner Spray) (Outer Centre & Inner Spray) WARNING! Switch OFF the electricity at the isolating switch and the water supply at the mains before removing the cover.
PAGE 12
I d) Display behaves erratically. Switch OFF electricity at ceiling/wall isolating switch, wait a few seconds, switch on again. (Note: The shower should be switched OFF each time after use at the ceiling/wall isolating switch. I I e) Water does not flow when START/STOP Note: If there is no water flowing then the shower will automatically switch OFF after about 5 seconds. button is pressed. I I Lights ON. Check the water supply is turned ON. I I “o” and “t” flashing in display.