Technical information

CONTENTS Table of Contents
COVER Book Cover
EDITION Edition Notice
FRONT_1 Notices
PREFACE About this Manual
CONTENTS Table of Contents
FRONT_2 Safety
FRONT_2.1 Safety Labels
FRONT_2.2 Safety at Work
FRONT_2.3 Cathode Ray Tube (CRT) Safety
FRONT_2.3.1 Storage of CRTs
FRONT_2.3.2 Maintenance and Installation of CRTs
FRONT_2.3.3 Disposal of CRTs
1.0 Part I. General Service Information
1.1 1. Operation
1.1.1 Display Modes
1.1.2 Operator Controls and Power-On Indicator
1.1.2.1 Contrast Control
1.1.2.2 Brightness Control
1.1.2.3 Power-On Indicator
1.1.3 Powering Off the System
1.2 2. Diagnostic Guide
1.2.1 Initial Checks
1.2.1.1 Visual check 0100
1.2.1.2 Power check 0110
1.2.2 Self-Test
1.2.3 Basic Function and Pattern Checks and Adjustments
1.2.4 Degaussing
1.3 3. Removal and Replacement
1.3.1 Tilt Swivel Stand
1.3.2 Lift Tilt Swivel Stand
1.3.3 Rear Cover
1.3.3.1 Rear Covers, Type 1
1.3.3.2 Rear Cover, Type 2
1.3.4 High Voltage Discharge Procedure
1.3.5 Card Tray Assemblies
1.3.6 Signal Cable
1.3.7 Integrated Tube Component (ITC)
1.3.8 Safety Check for Chassis Ground
2.0 Part II. Display-Specific Service Information
2.1 4. 6318/8511/8518-Specific Information
2.1.1 Display-Specific Removals and Replacements
2.1.1.1 Tilt Swivel Stand
2.1.1.2 Rear Cover
2.1.1.3 Card Tray Assembly
2.1.1.4 Signal Cables
2.1.1.5 Integrated Tube Component (ITC)
2.1.2 Functional Checks and Adjustments
2.1.2.1 Function Checks
2.1.2.2 Pattern Checks
2.1.2.3 Adjustment Procedures
2.1.3 Specifications
2.1.3.1 Physical Characteristics
2.1.3.2 Functional Characteristics
2.1.4 Locations 6318/8511/8518 Display
2.1.4.1 Safety Grounds
2.1.4.2 Parts Locations
2.2 5. 8513-Specific Information
2.2.1 Display-Specific Removals and Replacements
2.2.1.1 Tilt Swivel Stand
2.2.1.2 Rear Cover
2.2.1.3 Control Bridge Assembly
2.2.1.4 Card Tray Assembly
2.2.1.5 Integrated Tube Component (ITC)
2.2.2 Functional Checks and Adjustments
2.2.2.1 Function Checks
2.2.2.2 Pattern Checks
2.2.2.3 Adjustment Procedures
2.2.3 Specifications
2.2.3.1 Physical Characteristics
2.2.3.2 Functional Characteristics
2.2.4 Locations
2.2.4.1 Card Locations
2.2.4.2 Cable Connection Locations
2.3 6. 8515-Specific Information
2.3.1 Display-Specific Removals and Replacements
2.3.1.1 Tilt Swivel Stand
2.3.1.2 Rear Cover
2.3.1.3 Shield Cover
2.3.1.4 Card Tray Assembly
2.3.1.5 Signal Cable
2.3.1.6 Integrated Tube Component (ITC)
2.3.2 Functional Checks and Adjustments
2.3.2.1 Function Checks
PS/2 Displays Maintenance Manual
Table of Contents
¦ Copyright IBM Corp. 1993
CONTENTS - 1