Installation guide

© 2005 Directed Electronics—all rights reserved
4477
22--99 FFAACCTTOORRYY AALLAARRMM DDIISSAARRMM WWIITTHH CCHHAANNNNEELL 22::
In the default setting the factory alarm disarm output will disarm
the factory alarm system any time the button(s) controlling Channel Two is pressed.
22--1100 FFAACCTTOORRYY AALLAARRMM DDIISSAARRMM——WWIITTHH UUNNLLOOCCKK,,
BEFORE UNLOCK, REMOTE START ONLY
::
In the default setting the
factory alarm disarm output will disarm the factory alarm system any time the button(s) controlling Unlock is pressed.
The “Before Unlock” output to disarms the factory alarm before the unlock output activates and before remote start
is activated. The “Remote Start Only” output disarms the factory alarm only before the remote start is activated.
22--1111 FFAACCTTOORRYY AAL
LAARRMM DDIISSAARRMM PPUULLSSEESS——SSIINNGGLLEE,,
DOUBLE
::
Selectable for a single or double-pulse for the vehicle’s
factory alarm disarm input requirements.
22--1122 CCHHAANNNNEELL 44 VVAALLIIDDIITTYY//
LATCHED
//
LATCHED RESET WITH IGNITION
//
30 SECOND TIMED
OOUUTTPPUUTT::
This wire pro-
vides a (-) 200mA output whenever the transmitter button(s) controlling Channel 4 is pressed. This output can
be programmed to provide the following types of outputs (see also the
Feature Menus section):
■
VVaalliiddiittyy::
Output that will send a signal as long as the transmission is received.
■
LLaattcchheedd::
Output that will send a signal when the Channel 4 button(s) is pressed and will continue until the
same button(s) is pressed again.
■
LLaattcchheedd,, rreesseett wwiitthh iiggnniittiioonn::
Similar to the latched output, this type of output turns on the first time the
Channel 4 button(s) is pressed and turns off the next time the same button is pressed. This type of output
additionally stops and resets whenever the ignition is turned on and then off.
■
3300--sseeccoonndd ttiimmeedd::
Output that will send a continuous signal for 30 seconds.
NNoottee::
All auxilary channel timed outputs can be programmed using the Bitwriter® (1-90
seconds).
22--1133 CCHHAANNNNEELL 44 LLIINNKKIINNGG ((NNOONNEE))//
ARM, DISARM, REMOTE START
::
When programming to validity or timed output
this can be programmed to activate when arming or disarming (or remote starting) with the transmitter.
22--1144 CCHHAANNNNEELL 55 VVAALLIIDDIITTYY//
LATCHED
//
LATCHED RESET WITH IGNITION
//
30 SECOND TIMED
OOUUTTPPUUTT::
Channel Five can
be programmed for these output configurations. The unit is set to the default validity output. To change the con-
figuration, use the two-chirp setting to toggle through the different configurations. Refer to feature 2-10 for
additional detail.
22--1155 CCHHAANNNNEELL 55 LLIINNKKIIN
NGG ((NNOONNEE))//
ARM, DISARM, REMOTE START
::
Refer to feature 2-13 for additional detail.
22--1166 CCHHAANNNNEELL 66 VVAALLIIDDIITTYY//
LATCHED
//
LATCHED RESET WITH IGNITION
//
30 SECOND TIMED
OOUUTTPPUUTT::
Channel Five can
be programmed for these output configurations. The unit is set to the default validity output. To change the con-
figuration, use the two-chirp setting to toggle through the different configurations. Refer to feature 2-10 for
additional detail.
22--1177 CCHHAANNNNEELL 66 LLIINNKKIINNGG ((NNOONNEE))//
ARM, DISARM, REMOTE START
::
Refer to feature 2-13 for additional detail.