Installation Manual

Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the tabs on the mounting plate
touch the bottom of the cabinet when pushed
flush against the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
3
4
ATTACH THE MOUNTING
PLATE TO THE WALL
A1.
12
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
Remove the toggle wings from the bolts.
Insert the bolts into the mounting plate
through the holes designated to go into drywall
and reattach the toggle wings to
3
⁄4w (19 mm) onto
each bolt.
1
INSTALLATION OVERVIEW
A1. Attach Mounting Plate to Wall
A2. Prepare Top Cabinet
Mount Microwave Oven
A5.
Adjust Exhaust Adaptor
A6.
Wall
Mounting
Plate
Spacing for Toggles
More Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
To use toggle bolts:
Installation Instructions
2
OUTSIDE TOP EXHAUST (Vertical Duct)
A
IMPORTANT NOTES:
• Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
• Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
A7. Connect Ductwork
A3.
A4.
Check Damper Operation
Adapting Microwave Blower for
Outside Top Exhaust
3/
8"TO
EDG
E
%#
76
+
10
Ä
+(
':*#756
#&#
2614+5215+6
+10
'&1765+&'
4'%
1/
/'0
&'&&+/'05+10)4'#
5'Ä
.
#&'0#
+49+.
.
&+5%*#
4)'
+06
1*175'56
4
7%674'
/+0+/7/9+&6*4'37+
4'&
4'#49#..6'/2.#6'
NO
TE:
IT IS
VERY
I
MPORTANT TO
READ AND FO
LLOWT
HE
D
IRECTIONS
IN THE INSTALLAT
ION INSTRUCTI
ON
S
BEFORE PR
O
CEEDINGWITH
TH
IS
REAR WALL TEMPLATE.
This R
e
arWa
ll Te
mpl
a
te se
rves
to p
o
s
itio
n th
e bottom
mounting
pla
teand to loc
a
te th
e ho
r
iz
on
ta
l e
xhau
st
ou
tlet.
1. Use a l
e
vel
to ch
ec
k
th
at the te
mpla
te i
s
po
sit
ioned
ac
cu
r
ately
.
2. L
oc
ate andmark a
t lea
st o
nes
tud
on theleft
or
r
ight
s
ide of th
e c
enterli
ne.
016'
It is imp
o
rta
n
t to u
se at le
as
t one
wo
od
sc
rew
mounted
firmly
i
n a s
tud
to supp
ort the w
eight
ofthe micro
w
a
ve. M
a
rk tw
o additi
on
a
l, ev
en
ly
spa
c
ed
loc
atio
n
s
for the su
ppl
ied to
ggle bol
t
s.
3. Dr
ill h
ole
s in th
e marked locatio
ns
.Where t
her
e is
a
s
tud
,
dril
l
a 3/1
6"
hole
for woo
d sc
r
ew
s. F
o
r h
o
les
thatdo
n
o
t lin
e up
w
ith
a
stud, d
r
ill 5
/8"
hole
s
fo
r
to
ggle bolts
.
016
'
DO NOT I
N
S
T
AL
L THE MO
U
NTI
N
G
P
L
ATE
AT
T
HIST
IME.
4. Re
mov
e
th
e te
mpla
te fr
o
mthe rea
r
wal
l.
5.Re
v
iewthe Ins
ta
ll
a
ti
onInst
r
uc
ti
o
n bo
ok
for y
ou
r
in
stal
la
tion situa
ti
on.
Locat
e and m
ark holes to align with holes in t
he
mounting
plate.
IMPORTANT:
LO
C
A
T
E
AT LEAST O
NE STUD
O
N EIT
HERSID
E O
F
THE CENT
E
RLIN
E
.
MARKT
HE LOCATIONF
O
R 2 ADDIT
ION
A
L, EVENLY
SP
ACE
D T
O
GGLE BOLTS IN
THE MOUN
TING
PLATE
AREA.
Locate and mar
k
holes to ali
gn with holes in t
he
mountingplate.
IMPORTANT
:
LOC
A
T
E AT LEA
ST O
N
E
STUD
O
N EI
THER SI
D
E O
F
TH
E CENT
E
R
LIN
E
.
MARKTHE LO
CATIO
NF
OR 2 ADDITIONA
L, EV
ENL
Y
SPACEDTOG
GLE BOLTS IN THE MOUN
TING PLATE
AREA
.
Trim the re
ar wall tem
plat
e alongthe do
tted line.
Trim the rear wall templa
te along
the dotted line.
%
(%76176(14*14+<106#.
1765+&'':*#756
%7
6
*1.
'6
*4
17)*4'#49
#.
.
(14
':*#
756
#&#
26
14
12"
4"
Da
rlev
u
e
lt
a
a
laho
j
apara
c
o
nsu
l
tar
la
v
er
si
óne
n
Espa
ñol.