Instruments and Effects
Table Of Contents
- Logic Studio Instruments and Effects
- Contents
- Introduction to the Logic Studio Plugins
- Amp Modeling
- Delay
- Distortion
- Dynamics
- EQ
- Filter
- Imaging
- Metering
- Modulation
- Pitch
- Reverb
- Convolution Reverb: Space Designer
- Specialized
- Utility
- EVOC 20 PolySynth
- EFM1
- ES E
- ES M
- ES P
- ES1
- ES2
- The ES2 Parameters
- Tutorials
- Sound Workshop
- Sound Design From Scratch, Filter Settings, Digiwaves
- Three Detuned Sawtooth Oscillators and Unison Mode
- Extremely Detuned Monophonic Analog Sounds, Effects
- Clean Bass Settings With One Oscillator Only
- Distorted Analog Basses
- FM Intensity and Frequency
- Controlling FM Intensity by an Envelope and FM Scaling
- FM With Drive and Filter-FM
- FM With Digiwaves
- FM With Wavetables
- Distorted FM in Monophonic Unison
- FM With Unusual Spectra
- Slow and Fast Pulse Width Modulations With Oscillator 2
- Pulse Width Modulation With Two Oscillators, PWM Strings
- Ring Modulation
- Oscillator Synchronization
- First Steps in Vector Synthesis
- Vector Synthesis—XY Pad
- Vector Synthesis Loops
- Bass Drum With Self-Oscillating Filter and Vector Envelope
- Percussive Synthesizers and Basses With Two Filter Decay Phases
- Templates for the ES2
- Sound Workshop
- EVB3
- EVD6
- EVP88
- EXS24 mkII
- Learning About Sampler Instruments
- Loading Sampler Instruments
- Working With Sampler Instrument Settings
- Managing Sampler Instruments
- Searching for Sampler Instruments
- Importing Sampler Instruments
- Parameters Window
- The Instrument Editor
- Setting Sampler Preferences
- Configuring Virtual Memory
- Using the VSL Performance Tool
- External Instrument
- Klopfgeist
- Sculpture
- The Synthesis Core of Sculpture
- Sculpture’s Parameters
- Programming: Quick Start Guide
- Programming: In Depth
- Ultrabeat
- GarageBand Instruments
- Synthesizer Basics
- Glossary
- Index
Chapter 29 Ultrabeat 561
 Paste Sequence > (submenu): Use to replace all, or individual sequences, of the target
drum sound. Paste Sequence has no impact on the target drum sound. Pasting a
single sequence replaces the currently active sequence (as set in the Pattern menu)
of the target drum sound. This allows you to import drum sound sequences into any
of the 24 possible pattern locations. Note that these operations only affect the
selected drum sound, all sequence and sound data of the other 24 drum sounds
remain untouched.
 Swap with Clipboard: Swaps the content of the Clipboard with the target drum
sound. As this command swaps both drum sound and sequence data, it’s very useful
for reorganization of your drum kit.
Dragging EXS Instruments Into the Assignment Section
You can also drag an EXS instrument directly onto the Assignment section to import
the entire EXS instrument. This method does not allow paging through the EXS
instrument if it contains more than 25 sounds of sample material. Ultrabeat will only
map those sample zones and layers within Ultrabeat’s drum sound range of C1 to C3,
and ignore the rest.
The Mixer
The Assignment section contains a mixer for the 25 sounds found in an Ultrabeat drum
kit. It allows you to adjust each sound’s volume and pan position, and also offers a
Mute and Solo button.
Volume
The individual volumes of all sounds are indicated by blue bars, providing a complete
overview of all levels within the kit. You can adjust the volume of the sound, in relation
to Ultrabeat’s total output level, by dragging the blue bar beneath the sound name.
The Master (Volume) control is found above the 25th drum sound and controls the
levels of all drum sounds in the kit: put another way, the overall mix level of all drum
sounds.
Mute button
Volume slider
Master volume Pan knob
Output Selection menu
Solo button