Instruments and Effects
Table Of Contents
- Logic Studio Instruments and Effects
- Contents
- Introduction to the Logic Studio Plugins
- Amp Modeling
- Delay
- Distortion
- Dynamics
- EQ
- Filter
- Imaging
- Metering
- Modulation
- Pitch
- Reverb
- Convolution Reverb: Space Designer
- Specialized
- Utility
- EVOC 20 PolySynth
- EFM1
- ES E
- ES M
- ES P
- ES1
- ES2
- The ES2 Parameters
- Tutorials
- Sound Workshop
- Sound Design From Scratch, Filter Settings, Digiwaves
- Three Detuned Sawtooth Oscillators and Unison Mode
- Extremely Detuned Monophonic Analog Sounds, Effects
- Clean Bass Settings With One Oscillator Only
- Distorted Analog Basses
- FM Intensity and Frequency
- Controlling FM Intensity by an Envelope and FM Scaling
- FM With Drive and Filter-FM
- FM With Digiwaves
- FM With Wavetables
- Distorted FM in Monophonic Unison
- FM With Unusual Spectra
- Slow and Fast Pulse Width Modulations With Oscillator 2
- Pulse Width Modulation With Two Oscillators, PWM Strings
- Ring Modulation
- Oscillator Synchronization
- First Steps in Vector Synthesis
- Vector Synthesis—XY Pad
- Vector Synthesis Loops
- Bass Drum With Self-Oscillating Filter and Vector Envelope
- Percussive Synthesizers and Basses With Two Filter Decay Phases
- Templates for the ES2
- Sound Workshop
- EVB3
- EVD6
- EVP88
- EXS24 mkII
- Learning About Sampler Instruments
- Loading Sampler Instruments
- Working With Sampler Instrument Settings
- Managing Sampler Instruments
- Searching for Sampler Instruments
- Importing Sampler Instruments
- Parameters Window
- The Instrument Editor
- Setting Sampler Preferences
- Configuring Virtual Memory
- Using the VSL Performance Tool
- External Instrument
- Klopfgeist
- Sculpture
- The Synthesis Core of Sculpture
- Sculpture’s Parameters
- Programming: Quick Start Guide
- Programming: In Depth
- Ultrabeat
- GarageBand Instruments
- Synthesizer Basics
- Glossary
- Index
Chapter 28 Sculpture 495
 The maximum time/length of the envelope is 48 bars/40 seconds.
 The lines on the background grid are placed 100 milliseconds apart.
 The background lines are placed 1000 ms apart for very long displayed envelope
times. In sync mode, this is displayed as 1 quarter.
 The envelope is zoomed automatically after releasing the mouse button. This allows
the display of the entire envelope at the highest possible resolution for the graphic
envelope display.
 This behavior can be disabled/enabled by clicking the Autozoom button—the small
magnifying glass.
 Autozoom is automatically disabled when you perform a manual zoom—by click-
holding on the envelope display background, and dragging horizontally. As a
reference, the current display width is displayed by the numerical entry at the top
right of the display. You can re-engage automatic zooming by clicking on the
Autozoom button.
 If you click on the handles (nodes) or lines between the nodes in the envelope
display, the current envelope segment will be highlighted. A small help tag also
indicates the millisecond value of the current segment.
Envelope Handling
When first opened, a default envelope curve is automatically created for each envelope.
To view either, click the Env button in the Mode section.
You will see a few handles (nodes) placed—from left to right—along a straight line
within the envelope. These are indicators of the following parameters.
 Node 1: Start level
 Node 2: Attack time position/level
 Node 3: Loop time position/level (can be freely positioned).
 Node 4: Sustain time position/level (can be freely positioned).
 Node 5: End time position/level.
As you move your mouse cursor along the line, or hover over the nodes directly, the
current envelope segment is highlighted.
You can create your own envelopes manually, by manipulating the nodes and lines, or
you may record an envelope, as discussed in “Recording an Envelope” on page 497.
To adjust the time between nodes, click on the desired handle, and drag it left or right.
As you do so, the overall length of the envelope will change—with all following nodes
being moved.