Instruments and Effects
Table Of Contents
- Logic Studio Instruments and Effects
- Contents
- Introduction to the Logic Studio Plugins
- Amp Modeling
- Delay
- Distortion
- Dynamics
- EQ
- Filter
- Imaging
- Metering
- Modulation
- Pitch
- Reverb
- Convolution Reverb: Space Designer
- Specialized
- Utility
- EVOC 20 PolySynth
- EFM1
- ES E
- ES M
- ES P
- ES1
- ES2
- The ES2 Parameters
- Tutorials
- Sound Workshop
- Sound Design From Scratch, Filter Settings, Digiwaves
- Three Detuned Sawtooth Oscillators and Unison Mode
- Extremely Detuned Monophonic Analog Sounds, Effects
- Clean Bass Settings With One Oscillator Only
- Distorted Analog Basses
- FM Intensity and Frequency
- Controlling FM Intensity by an Envelope and FM Scaling
- FM With Drive and Filter-FM
- FM With Digiwaves
- FM With Wavetables
- Distorted FM in Monophonic Unison
- FM With Unusual Spectra
- Slow and Fast Pulse Width Modulations With Oscillator 2
- Pulse Width Modulation With Two Oscillators, PWM Strings
- Ring Modulation
- Oscillator Synchronization
- First Steps in Vector Synthesis
- Vector Synthesis—XY Pad
- Vector Synthesis Loops
- Bass Drum With Self-Oscillating Filter and Vector Envelope
- Percussive Synthesizers and Basses With Two Filter Decay Phases
- Templates for the ES2
- Sound Workshop
- EVB3
- EVD6
- EVP88
- EXS24 mkII
- Learning About Sampler Instruments
- Loading Sampler Instruments
- Working With Sampler Instrument Settings
- Managing Sampler Instruments
- Searching for Sampler Instruments
- Importing Sampler Instruments
- Parameters Window
- The Instrument Editor
- Setting Sampler Preferences
- Configuring Virtual Memory
- Using the VSL Performance Tool
- External Instrument
- Klopfgeist
- Sculpture
- The Synthesis Core of Sculpture
- Sculpture’s Parameters
- Programming: Quick Start Guide
- Programming: In Depth
- Ultrabeat
- GarageBand Instruments
- Synthesizer Basics
- Glossary
- Index
182 Chapter 12 Convolution Reverb: Space Designer
 Zoom to Fit button: Switch on to display the entire impulse response waveform. The
display will automatically follow any envelope length changes.
 A and D buttons: Click to limit the Zoom to Fit function to the attack and decay
portions of the (currently selected) envelope. The A and D buttons are available only
to the volume and filter envelopes.
Setting Envelope Parameters
Space Designer allows you to edit the volume and filter envelopes of all IRs, and the
density envelope of synthesized IRs. All three envelopes can be adjusted both
graphically and numerically (in the parameter bar).
While some parameters are envelope-specific, all envelopes consist of the Attack Time
and Decay Time parameters: The combined total of the Attack Time and Decay Time
parameters is equal to the total length of the (synthesized or sampled) impulse
response (determined by the Length parameter, see “Setting the Length of the Impulse
Response” on page 174), unless the Decay time is reduced.
 You can change the curve shape by dragging the envelope curve directly. Use the
small nodes attached to a line for finer adjustments to envelope curves. They are tied
to the envelope curve itself, so you can view them as envelope handles. Moving the
nodes vertically or horizontally will change the shape of the envelope curve.
 The large nodes are value indicators of the parameters that appear in the horizontal
parameter bar below—Init Level, Attack Time, Decay Time, and so on. If you edit any
numerical value, the corresponding node will move in the main display. Try this with
each numerical parameter to establish which node is which. When you move the
mouse pointer over one of these nodes, you’ll see a pair of arrows. The arrows simply
indicate the possible directions that the node can be moved.