2009
Table Of Contents
- Logic Studio Effects
- Contents
- An Introduction to the Logic Studio Effects
- Amps and Pedals
- Amp Designer
- Choosing an Amp Designer Model
- Tweed Combos
- Classic American Combos
- British Stacks
- British Combos
- British Alternatives
- Metal Stacks
- Additional Combos
- Building a Customized Amp Designer Combo
- Choosing an Amp Designer Amplifier
- Choosing an Amp Designer Cabinet
- Amp Designer Cabinet Reference Table
- Using Amp Designer’s Equalizer
- Amp Designer Equalizer Type Reference Table
- Using Amp Designer’s Gain, Presence, and Master Controls
- Getting to Know Amp Designer’s Effects Parameters
- Using Amp Designer’s Reverb Effect
- Amp Designer Reverb Type Reference Table
- Using Amp Designer’s Tremolo and Vibrato Effects
- Setting Amp Designer Microphone Parameters
- Setting Amp Designer’s Output Level
- Bass Amp
- Guitar Amp Pro
- Building Your Guitar Amp Pro Model
- Choosing a Guitar Amp Pro Amplifier
- Choosing a Guitar Amp Pro Speaker Cabinet
- Choosing a Guitar Amp Pro Equalizer
- Using Guitar Amp Pro’s Gain, Tone, Presence, and Master Controls
- Getting to Know Guitar Amp Pro’s Effects Section
- Using Guitar Amp Pro’s Tremolo and Vibrato Effects
- Using Guitar Amp Pro’s Reverb Effect
- Setting Guitar Amp Pro Microphone Parameters
- Setting the Guitar Amp Pro Output Level
- Pedalboard
- Amp Designer
- Delay Effects
- Delay Designer
- Getting to Know the Delay Designer Interface
- Getting to Know Delay Designer’s Main Display
- Using Delay Designer’s View Buttons
- Zooming and Navigating Delay Designer’s Tap Display
- Creating Taps in Delay Designer
- Selecting Taps in Delay Designer
- Moving and Deleting Taps in Delay Designer
- Using Delay Designer’s Tap Toggle Buttons
- Editing Parameters in Delay Designer’s Tap Display
- Aligning Delay Designer Tap Values
- Editing Filter Cutoff in Delay Designer’s Tap Display
- Editing Pan in Delay Designer’s Tap Display
- Editing Taps in Delay Designer’s Tap Parameter Bar
- Editing Delay Designer Taps with the Shortcut Menu
- Resetting Delay Designer Tap Values
- Synchronizing Taps in Delay Designer
- Using Delay Designer’s Master Section
- Working with Delay Designer in Surround
- Echo
- Sample Delay
- Stereo Delay
- Tape Delay
- Delay Designer
- Distortion Effects
- Dynamics Processors
- Equalizers
- Filter Effects
- AutoFilter
- EVOC 20 Filterbank
- EVOC 20 TrackOscillator
- What Is a Vocoder?
- How Does a Vocoder Work?
- Getting to Know the EVOC 20 TrackOscillator Interface
- EVOC 20 TrackOscillator Analysis In Parameters
- Using EVOC 20 TrackOscillator Analysis In Parameters
- EVOC 20 TrackOscillator U/V Detection Parameters
- EVOC 20 TrackOscillator Synthesis In Parameters
- Basic Tracking Oscillator Parameters
- Tracking Oscillator Pitch Correction Parameters
- Quantizing the Pitch of the Tracking Oscillator
- EVOC 20 TrackOscillator Formant Filter Parameters
- Using Formant Stretch and Formant Shift
- EVOC 20 TrackOscillator Modulation Parameters
- EVOC 20 TrackOscillator Output Parameters
- Fuzz-Wah
- Spectral Gate
- Imaging Processors
- Metering Tools
- Modulation Effects
- Pitch Effects
- Reverb Effects
- Space Designer Convolution Reverb
- Getting to Know the Space Designer Interface
- Working with Space Designer’s Impulse Response Parameters
- Working with Space Designer’s Envelope and EQ Parameters
- Working with Space Designer’s Filter
- Working with Space Designer’s Global Parameters
- Using Space Designer’s Input Slider
- Using Space Designer’s Latency Compensation Feature
- Using Space Designer’s Definition Parameter
- Using Space Designer’s Rev Vol Compensation
- Using Space Designer’s Output Sliders
- Working with Pre-Dly (Predelay) in Space Designer
- Using Space Designer’s IR Start Parameter
- Using Space Designer’s Spread Parameters
- Automating Space Designer
- Specialized Effects and Utilities
- Utilities and Tools
Note: Delay Designer offers a maximum delay time of 10 seconds. This means that if you
load a setting into a project with a slower tempo than the tempo at which it was created,
some taps may fall outside the 10-second limit. In such cases, these taps will not be played
but will be retained as part of the setting.
• Sync button: Enables or disables synchronized mode.
• Grid pop-up menu: Provides several grid resolutions, which correspond to musical note
durations. The grid resolution, along with the project tempo, determines the length of
each grid increment. As you change grid resolutions, the increments shown in the
Identification bar change accordingly. This also determines a step limitation for all taps.
As an example, imagine a project with the current tempo set to 120 beats per minute.
The Grid pop-up menu value is set to 1/16 notes. At this tempo and grid resolution,
each grid increment is 125 milliseconds (ms) apart. If Tap A is currently set to 380 ms,
turning on Sync mode would immediately shift Tap A to 375 ms. If you subsequently
moved Tap A forward in time, it would snap to 500 ms, 625 ms, 750 ms, and so on. At
a resolution of 1/8 notes, the steps are 250 milliseconds apart, so Tap A would
automatically snap to the nearest division (500 ms), and could be moved to 750 ms,
1000 ms, 1250 ms, and so on.
• Swing field: Determines how close to the absolute grid position every second grid
increment will be. A Swing setting of 50% means that every grid increment has the
same value. Settings below 50% result in every second increment being shorter in time.
Settings above 50% result in every second grid increment being longer in time.
71Chapter 2 Delay Effects