2009
Table Of Contents
- Logic Studio Effects
- Contents
- An Introduction to the Logic Studio Effects
- Amps and Pedals
- Amp Designer
- Choosing an Amp Designer Model
- Tweed Combos
- Classic American Combos
- British Stacks
- British Combos
- British Alternatives
- Metal Stacks
- Additional Combos
- Building a Customized Amp Designer Combo
- Choosing an Amp Designer Amplifier
- Choosing an Amp Designer Cabinet
- Amp Designer Cabinet Reference Table
- Using Amp Designer’s Equalizer
- Amp Designer Equalizer Type Reference Table
- Using Amp Designer’s Gain, Presence, and Master Controls
- Getting to Know Amp Designer’s Effects Parameters
- Using Amp Designer’s Reverb Effect
- Amp Designer Reverb Type Reference Table
- Using Amp Designer’s Tremolo and Vibrato Effects
- Setting Amp Designer Microphone Parameters
- Setting Amp Designer’s Output Level
- Bass Amp
- Guitar Amp Pro
- Building Your Guitar Amp Pro Model
- Choosing a Guitar Amp Pro Amplifier
- Choosing a Guitar Amp Pro Speaker Cabinet
- Choosing a Guitar Amp Pro Equalizer
- Using Guitar Amp Pro’s Gain, Tone, Presence, and Master Controls
- Getting to Know Guitar Amp Pro’s Effects Section
- Using Guitar Amp Pro’s Tremolo and Vibrato Effects
- Using Guitar Amp Pro’s Reverb Effect
- Setting Guitar Amp Pro Microphone Parameters
- Setting the Guitar Amp Pro Output Level
- Pedalboard
- Amp Designer
- Delay Effects
- Delay Designer
- Getting to Know the Delay Designer Interface
- Getting to Know Delay Designer’s Main Display
- Using Delay Designer’s View Buttons
- Zooming and Navigating Delay Designer’s Tap Display
- Creating Taps in Delay Designer
- Selecting Taps in Delay Designer
- Moving and Deleting Taps in Delay Designer
- Using Delay Designer’s Tap Toggle Buttons
- Editing Parameters in Delay Designer’s Tap Display
- Aligning Delay Designer Tap Values
- Editing Filter Cutoff in Delay Designer’s Tap Display
- Editing Pan in Delay Designer’s Tap Display
- Editing Taps in Delay Designer’s Tap Parameter Bar
- Editing Delay Designer Taps with the Shortcut Menu
- Resetting Delay Designer Tap Values
- Synchronizing Taps in Delay Designer
- Using Delay Designer’s Master Section
- Working with Delay Designer in Surround
- Echo
- Sample Delay
- Stereo Delay
- Tape Delay
- Delay Designer
- Distortion Effects
- Dynamics Processors
- Equalizers
- Filter Effects
- AutoFilter
- EVOC 20 Filterbank
- EVOC 20 TrackOscillator
- What Is a Vocoder?
- How Does a Vocoder Work?
- Getting to Know the EVOC 20 TrackOscillator Interface
- EVOC 20 TrackOscillator Analysis In Parameters
- Using EVOC 20 TrackOscillator Analysis In Parameters
- EVOC 20 TrackOscillator U/V Detection Parameters
- EVOC 20 TrackOscillator Synthesis In Parameters
- Basic Tracking Oscillator Parameters
- Tracking Oscillator Pitch Correction Parameters
- Quantizing the Pitch of the Tracking Oscillator
- EVOC 20 TrackOscillator Formant Filter Parameters
- Using Formant Stretch and Formant Shift
- EVOC 20 TrackOscillator Modulation Parameters
- EVOC 20 TrackOscillator Output Parameters
- Fuzz-Wah
- Spectral Gate
- Imaging Processors
- Metering Tools
- Modulation Effects
- Pitch Effects
- Reverb Effects
- Space Designer Convolution Reverb
- Getting to Know the Space Designer Interface
- Working with Space Designer’s Impulse Response Parameters
- Working with Space Designer’s Envelope and EQ Parameters
- Working with Space Designer’s Filter
- Working with Space Designer’s Global Parameters
- Using Space Designer’s Input Slider
- Using Space Designer’s Latency Compensation Feature
- Using Space Designer’s Definition Parameter
- Using Space Designer’s Rev Vol Compensation
- Using Space Designer’s Output Sliders
- Working with Pre-Dly (Predelay) in Space Designer
- Using Space Designer’s IR Start Parameter
- Using Space Designer’s Spread Parameters
- Automating Space Designer
- Specialized Effects and Utilities
- Utilities and Tools
Depending on the chosen surround format, a number of points that indicate speaker
positions are shown (L, R, C, Ls, Rs in a 5.1 configuration is displayed in the figure). Lines
connect these points. The center position of each connecting line is indicated by a blue
marker.
A gray ball indicates the surround field/sound placement. As you move the surround
panner of the channel strip, the ball in the Correlation Meter mirrors your movements.
The blue markers also move in real time, with shaded gray lines indicating the divergence
from the centered positions on each of the connecting lines.
The LFE channel Correlation Meter is shown at the bottom of the main display. The
horizontal area around the white correlation indicator denotes phase correlation deviations
in real time. This is shown in both directions. A vertical red line to the left of the correlation
indicator shows the maximum negative phase deviation value. You can reset this line by
clicking on it during playback.
The LFE Correlation Meter’s scale values indicate the following:
• A +1 correlation value indicates that the signal is balanced.
• Correlation values in the blue zone (between +1 and the middle position) indicate that
the signal is mono compatible.
• The middle position indicates the highest allowable amount of channel divergence.
• When the meter moves into the red area to the left of the center position, out-of-balance
material is present.
Surround MultiMeter Peak Parameters
The Surround MultiMeter offers the following Peak parameters:
• Hold button: Activates peak hold for all metering tools in the Surround MultiMeter, as
follows:
• Analyzer: A small yellow segment above each level bar indicates the most recent
peak level.
• Goniometer: All illuminated pixels are held during a peak hold.
• Level Meter: A small yellow segment above each level bar indicates the most recent
peak level.
• Balance/Correlation Meter: The horizontal area around the white correlation indicator
denotes phase correlation deviations in real time, in both directions.
181Chapter 8 Metering Tools