8
Table Of Contents
- Logic Express 8 Control Surfaces Support
- Contents
- Introduction
- Basic Control Surface Setup
- Customizing Controller Assignments
- Mackie Control
- Setting Up Your Mackie Control
- Using the Mackie Control With Logic Express
- Display Zone
- Channel Strip Controls
- Master Fader
- Assignment Zone
- Fader Bank Zone
- Function Key Zone
- Global View Zone
- Modifier Buttons
- Automation Buttons
- Utilities Buttons
- Transport Zone
- Cursor Key Zone
- Jog/Scrub Wheel Zone
- Programmable User Modes
- Connecting Foot Switches
- Assignment Overview
- M-Audio iControl
- CM Labs Motormix
- Frontier Design TranzPort
- JLCooper CS-32 MiniDesk
- JLCooper FaderMaster 4/100
- Korg microKONTROL and KONTROL49
- Mackie Baby HUI
- Mackie C4
- Mackie HUI
- Radikal Technologies SAC-2K
- Roland SI-24
- Tascam FW-1884
- Tascam US-2400
- Tascam US-428 and US-224
- Yamaha 01V96
- Yamaha 02R96
- Yamaha DM1000
- Yamaha DM2000
212 Chapter 18 Yamaha 01V96
Assignment Overview
A modifier button (such as SHIFT) below a button description indicates that the button
has an alternate function/use, while holding down this modifier.
DISPLAY ACCESS Section
FADER MODE Section
Control Assignment
AUTOMIX While held, the channel strip displays show the current automation mode.
PAIR/GROUP Enters Group Edit mode:
 The upper line in the DSP Edit Section (shown in the control surface’s display)
shows the number and name of the group being edited.
 Parameter control buttons F1 to F4 switch the properties of the group being
edited. The group name is shown in the lower line.
 When the INSERT/PARAM button is set to Insert, the Parameter wheel scrolls
through the group properties. At other times, it selects the group currently
being edited.
 The SELECT buttons enable/disable group membership of the channel.
DAW SHIFT/ADD Switches to a view of channels used by Arrange tracks.
EFFECT Hides or shows the Sample Editor.
Control Assignment
AUX 1 Assigns Send 1 Level to encoders, and Send 1 to 4 Levels to DSP encoders. While
held, the channel strip displays show the current Send 1 Destination assignment.
DAW SHIFT/ADD As above, for Send 6.
AUX 2 Assigns Send 2 Level to encoders, and Send 1 to 4 Levels to DSP encoders. While
held, the channel strip displays show the current Send 2 Destination assignment.
DAW SHIFT/ADD As above, for Send 7.
AUX 3 Assigns Send 3 Level to encoders, and Send 1 to 4 Levels to DSP encoders. While
held, the channel strip displays show the current Send 3 Destination assignment.
DAW SHIFT/ADD As above, for Send 8.
AUX 4 Assigns Send 4 Level to encoders, and Send 1 to 4 Levels to DSP encoders. While
held, the channel strip displays show the current Send 4 Destination assignment.
AUX 5 Assigns Send 5 Level to encoders, and Send 5 to 8 Levels to DSP encoders. While
held, the channel strip displays show the current Send 5 Destination assignment.
AUX 6 Switches Encoder Select buttons between normal behavior and setting default
value.
AUX 7 Assigns Pan to encoders; assigns selected channel’s pan parameters to DSP
encoders.
AUX 8 Determines mode of channel strip SEL buttons when channel strip AUTO button
is off:
 Indicator off: Track/channel selection.
 Indicator on: Insert selection.
HOME Enables or disables Flip mode.