8
Table Of Contents
- Logic Express 8 Control Surfaces Support
- Contents
- Introduction
- Basic Control Surface Setup
- Customizing Controller Assignments
- Mackie Control
- Setting Up Your Mackie Control
- Using the Mackie Control With Logic Express
- Display Zone
- Channel Strip Controls
- Master Fader
- Assignment Zone
- Fader Bank Zone
- Function Key Zone
- Global View Zone
- Modifier Buttons
- Automation Buttons
- Utilities Buttons
- Transport Zone
- Cursor Key Zone
- Jog/Scrub Wheel Zone
- Programmable User Modes
- Connecting Foot Switches
- Assignment Overview
- M-Audio iControl
- CM Labs Motormix
- Frontier Design TranzPort
- JLCooper CS-32 MiniDesk
- JLCooper FaderMaster 4/100
- Korg microKONTROL and KONTROL49
- Mackie Baby HUI
- Mackie C4
- Mackie HUI
- Radikal Technologies SAC-2K
- Roland SI-24
- Tascam FW-1884
- Tascam US-2400
- Tascam US-428 and US-224
- Yamaha 01V96
- Yamaha 02R96
- Yamaha DM1000
- Yamaha DM2000
Chapter 13 Radikal Technologies SAC-2K 179
Mixer View Mode Section
Control Assignment
Pan Switches to Mixer view (multi-channel) pan editing.
High, HiMid, LowMid,
Low
Switches to Mixer view (multi-channel) gain editing of a certain EQ band.
Encoders 9 to 12 edit Frequency, Gain, Q factor, and On/Off for the selected
channel.
Pressing and releasing the button chooses a specific EQ band.
 Low: Band 3 (first parametric EQ band)
 LowMid: Band 4 (second parametric EQ band)
 HiMid: Band 5 (third parametric EQ band)
 High: Band 6 (fourth parametric EQ band)
While held down, you can use Encoder 9 to choose the EQ band that you
want to edit (bands 1 to 8).
The button’s LED is lit when in Mixer view gain editing mode (of the selected
channel EQ band).
Snd/Ins Switches the four Snd/Ins (1 to 4) buttons between Send and Insert modes.
 LED off: Send mode
 LED on: Insert mode
Snd/Ins 1 to 4 Â If in Send mode, switches to Mixer view (multi-channel) send level editing
of Sends 1 to 4.
Encoders 9 to 12 edit Destination, Level, Pre/Post and Mute of the selected
channel. You must confirm the Send destination by pushing the encoder
9 button.
While held down, use Encoder 9 to select the desired Send number (1 to 8).
The button’s LED is lit when in Mixer view send level editing mode (of the
selected channel send slot).
 If in Insert mode, switches to Mixer view plug-in selection for Inserts 1 to 4.
Plug-in selection is confirmed by pressing the encoder’s push-button.
While held down, use Encoder 9 to choose the desired Insert slot number
(1 to 15).
The button’s LED is lit when in plug-in selection mode (of the
corresponding channel insert slot).
Audio Switches to Mixer view, and displays audio channels.
SHIFT Switches to Mixer view.
MIDI Switches to Mixer view, and displays MIDI channel strips.
SHIFT Switches to Arrange (Track) view, and displays the channel strips of all tracks
used in Arrange.
Input Switches to Mixer view, and displays input channels.
SHIFT Switches to Mixer view, and displays the master and output channels.
Inst Switches to Mixer view, and displays (software) instrument channels.
SHIFT Switches to Mixer view, and displays aux channels.
Bus Switches to Mixer view, and displays bus channels.
SHIFT Switches to Single view.