9
Table Of Contents
- Logic Express 9 Effects
- Contents
- An Introduction to the Logic Express Effects
- Amps and Pedals
- Amp Designer
- Choosing an Amp Designer Model
- Tweed Combos
- Classic American Combos
- British Stacks
- British Combos
- British Alternatives
- Metal Stacks
- Additional Combos
- Building a Customized Amp Designer Combo
- Choosing an Amp Designer Amplifier
- Choosing an Amp Designer Cabinet
- Amp Designer Cabinet Reference Table
- Using Amp Designer’s Equalizer
- Amp Designer Equalizer Type Reference Table
- Using Amp Designer’s Gain, Presence, and Master Controls
- Getting to Know Amp Designer’s Effects Parameters
- Using Amp Designer’s Reverb Effect
- Amp Designer Reverb Type Reference Table
- Using Amp Designer’s Tremolo and Vibrato Effects
- Setting Amp Designer Microphone Parameters
- Setting Amp Designer’s Output Level
- Bass Amp
- Guitar Amp Pro
- Building Your Guitar Amp Pro Model
- Choosing a Guitar Amp Pro Amplifier
- Choosing a Guitar Amp Pro Speaker Cabinet
- Choosing a Guitar Amp Pro Equalizer
- Using Guitar Amp Pro’s Gain, Tone, Presence, and Master Controls
- Getting to Know Guitar Amp Pro’s Effects Section
- Using Guitar Amp Pro’s Tremolo and Vibrato Effects
- Using Guitar Amp Pro’s Reverb Effect
- Setting Guitar Amp Pro Microphone Parameters
- Setting the Guitar Amp Pro Output Level
- Pedalboard
- Amp Designer
- Delay Effects
- Distortion Effects
- Dynamics Processors
- Equalizers
- Filter Effects
- AutoFilter
- EVOC 20 Filterbank
- EVOC 20 TrackOscillator
- What Is a Vocoder?
- How Does a Vocoder Work?
- Getting to Know the EVOC 20 TrackOscillator Interface
- EVOC 20 TrackOscillator Analysis In Parameters
- Using EVOC 20 TrackOscillator Analysis In Parameters
- EVOC 20 TrackOscillator U/V Detection Parameters
- EVOC 20 TrackOscillator Synthesis In Parameters
- Basic Tracking Oscillator Parameters
- Tracking Oscillator Pitch Correction Parameters
- Quantizing the Pitch of the Tracking Oscillator
- EVOC 20 TrackOscillator Formant Filter Parameters
- Using Formant Stretch and Formant Shift
- EVOC 20 TrackOscillator Modulation Parameters
- EVOC 20 TrackOscillator Output Parameters
- Fuzz-Wah
- Spectral Gate
- Imaging Processors
- Metering Tools
- Modulation Effects
- Pitch Effects
- Reverb Effects
- Specialized Effects and Utilities
- Utilities and Tools
All stompbox knobs, switches, and sliders can be automated. Eight Macro controls enable
real time changes to any pedal parameter with a MIDI controller.
Macro Controls area
Pedal Browser
Pedal area
Routing area
• The Pedal Browser shows all pedal effects and utilities. These can be dragged into the
Pedal area as part of the signal chain. See Using Pedalboard’s Pedal Browser. This
interface area is also used for the alternative import mode. See Using Pedalboard’s
Import Mode.
• The Pedal area is where you determine the order of effects and set effect parameters.
You can add, replace, and remove stompboxes here. See Using Pedalboard’s Pedal
Area.
• The Routing area is used to control signal flow in the two effects busses (Bus A and
Bus B) available in Pedalboard. See Using Pedalboard’s Routing Area.
• The Macro Controls area is used to assign eight MIDI controllers, which can be used to
control any stompbox parameter in real time. See Using Pedalboard’s Macro Controls
Area.
• The effect and utility pedals are described in the following sections:
• Distortion Pedals
• Modulation Pedals
• Delay Pedals
• Filter Pedals
• Dynamics Pedals
• Utility Pedals
38 Chapter 1 Amps and Pedals