9
Table Of Contents
- Logic Express 9 Effects
- Contents
- An Introduction to the Logic Express Effects
- Amps and Pedals
- Amp Designer
- Choosing an Amp Designer Model
- Tweed Combos
- Classic American Combos
- British Stacks
- British Combos
- British Alternatives
- Metal Stacks
- Additional Combos
- Building a Customized Amp Designer Combo
- Choosing an Amp Designer Amplifier
- Choosing an Amp Designer Cabinet
- Amp Designer Cabinet Reference Table
- Using Amp Designer’s Equalizer
- Amp Designer Equalizer Type Reference Table
- Using Amp Designer’s Gain, Presence, and Master Controls
- Getting to Know Amp Designer’s Effects Parameters
- Using Amp Designer’s Reverb Effect
- Amp Designer Reverb Type Reference Table
- Using Amp Designer’s Tremolo and Vibrato Effects
- Setting Amp Designer Microphone Parameters
- Setting Amp Designer’s Output Level
- Bass Amp
- Guitar Amp Pro
- Building Your Guitar Amp Pro Model
- Choosing a Guitar Amp Pro Amplifier
- Choosing a Guitar Amp Pro Speaker Cabinet
- Choosing a Guitar Amp Pro Equalizer
- Using Guitar Amp Pro’s Gain, Tone, Presence, and Master Controls
- Getting to Know Guitar Amp Pro’s Effects Section
- Using Guitar Amp Pro’s Tremolo and Vibrato Effects
- Using Guitar Amp Pro’s Reverb Effect
- Setting Guitar Amp Pro Microphone Parameters
- Setting the Guitar Amp Pro Output Level
- Pedalboard
- Amp Designer
- Delay Effects
- Distortion Effects
- Dynamics Processors
- Equalizers
- Filter Effects
- AutoFilter
- EVOC 20 Filterbank
- EVOC 20 TrackOscillator
- What Is a Vocoder?
- How Does a Vocoder Work?
- Getting to Know the EVOC 20 TrackOscillator Interface
- EVOC 20 TrackOscillator Analysis In Parameters
- Using EVOC 20 TrackOscillator Analysis In Parameters
- EVOC 20 TrackOscillator U/V Detection Parameters
- EVOC 20 TrackOscillator Synthesis In Parameters
- Basic Tracking Oscillator Parameters
- Tracking Oscillator Pitch Correction Parameters
- Quantizing the Pitch of the Tracking Oscillator
- EVOC 20 TrackOscillator Formant Filter Parameters
- Using Formant Stretch and Formant Shift
- EVOC 20 TrackOscillator Modulation Parameters
- EVOC 20 TrackOscillator Output Parameters
- Fuzz-Wah
- Spectral Gate
- Imaging Processors
- Metering Tools
- Modulation Effects
- Pitch Effects
- Reverb Effects
- Specialized Effects and Utilities
- Utilities and Tools
• Level knob: Sets the amount of reverb applied to the pre-amplified signal.
Amp Designer Reverb Type Reference Table
You can choose a reverb type by clicking the Reverb label in the center of the Amp section.
The table below covers the properties of each reverb type available in Amp Designer.
DescriptionReverb type
This bright, splashy sound has largely defined combo amp reverb
since the early 1960s.
Vintage Spring
A darker, subtler spring sound.Simple Spring
An even darker, somewhat low-fidelity spring sound.Mellow Spring
Has some of the brilliance of Vintage Spring, but with less surf-style
splash.
Bright Spring
A moody-sounding spring. More restrained than Mellow Spring.Dark Spring
Another 1960s-style spring with a strong, slightly distorted
mid-range emphasis.
Resonant Spring
A modernized version of the classic Vintage Spring with a richer
tone in the bass and mids.
Boutique Spring
A smooth modern reverb with rich lows and restrained highs.Sweet Reverb
A bold, well-balanced modern reverb.Rich Reverb
A lush modern reverb with rich low-mids and understated highs.Warm Reverb
Using Amp Designer’s Tremolo and Vibrato Effects
Tremolo and vibrato are controlled by several switches and two knobs in the Effects
section found toward the right of the knobs section. Tremolo modulates the amplitude
or volume of the sound, and vibrato modulates the pitch.
• On/Off switch: Enables or disables the tremolo or vibrato effect.
• Trem/Vib switch: Choose either tremolo or vibrato.
• Depth knob: Sets the intensity of the modulation (tremolo or vibrato).
• Speed knob: Sets the speed of the modulation in Hertz. Lower settings produce a
smooth, floating sound. Higher settings produce a rotor-like effect.
27Chapter 1 Amps and Pedals