8
Table Of Contents
- Logic Express 8 Instruments and Effects
- Contents
- Introduction to the Logic Express Plugins
- Amp Modeling
- Delay
- Distortion
- Dynamics
- EQ
- Filter
- Imaging
- Metering
- Modulation
- Pitch
- Reverb
- Specialized
- Utility
- EVOC 20 PolySynth
- EFM1
- ES E
- ES M
- ES P
- ES1
- ES2
- The ES2 Parameters
- Tutorials
- Sound Workshop
- Sound Design From Scratch, Filter Settings, Digiwaves
- Three Detuned Sawtooth Oscillators and Unison Mode
- Extremely Detuned Monophonic Analog Sounds, Effects
- Clean Bass Settings With One Oscillator Only
- Distorted Analog Basses
- FM Intensity and Frequency
- Controlling FM Intensity by an Envelope and FM Scaling
- FM With Drive and Filter-FM
- FM With Digiwaves
- FM With Wavetables
- Distorted FM in Monophonic Unison
- FM With Unusual Spectra
- Slow and Fast Pulse Width Modulations With Oscillator 2
- Pulse Width Modulation With Two Oscillators, PWM Strings
- Ring Modulation
- Oscillator Synchronization
- First Steps in Vector Synthesis
- Vector Synthesis—XY Pad
- Vector Synthesis Loops
- Bass Drum With Self-Oscillating Filter and Vector Envelope
- Percussive Synthesizers and Basses With Two Filter Decay Phases
- Templates for the ES2
- Sound Workshop
- EXS24 mkII
- Learning About Sampler Instruments
- Loading Sampler Instruments
- Working With Sampler Instrument Settings
- Managing Sampler Instruments
- Searching for Sampler Instruments
- Importing Sampler Instruments
- Parameters Window
- The Instrument Editor
- Setting Sampler Preferences
- Configuring Virtual Memory
- Using the VSL Performance Tool
- External Instrument
- Klopfgeist
- Ultrabeat
- GarageBand Instruments
- Synthesizer Basics
- Glossary
- Index
58 Chapter 5 EQ
 Band 7 is a high shelving filter.
 Band 8 is a lowpass filter.
 Graphic display: Shows the current curve of each EQ band. You can adjust the
frequency of each band by dragging left or right in the section of the display for that
band, and adjust the gain of each band (except bands 1 and 8) by dragging up or
down in the band’s section. The display reflects your changes immediately.
Parameter Section
Below the graphic display area are controls that you can use to show the settings for
each band and adjust each band’s settings.
 Frequency fields: Adjust the frequency of each band.
 Gain/Slope fields: Adjust the amount of gain for each band. For bands 1 and 8, this
changes the slope of the filter.
 Q fields: Adjust the Q or resonance for each band (the range of frequencies around
the center frequency that are affected).
The Q parameter of band 1 and band 8 has no effect when the slope is set to 6 dB/
Oct. When the Q parameter of bands 3 through 6 is set to an extremely high value
(such as 100), these filters only affect a very narrow frequency band, and can be used
as notch filters.
 Link button: Activates Gain-Q coupling, which automatically adjusts the Q
(bandwidth) when you raise or lower the gain on any EQ band, to preserve the
perceived bandwidth of the bell curve.
Setting Gain-Q Couple to strong preserves the perceived bandwidth almost entirely,
while light and medium settings allow some change as you raise or lower the gain.
The asymmetric settings feature a stronger coupling for negative gain values than for
positive values, so the perceived bandwidth is more closely preserved when you cut
than when you boost gain.
Note: If you play back automation of the Q parameter with a different Gain-Q Couple
setting, the actual Q values will be different than when the automation was recorded.
 Analyzer Mode pop-up menu (extended parameter): Choose Peak or RMS.
 Analyzer Decay slider and field (extended parameter): Adjust the decay rate (in dB per
second) of the Analyzer curve (peak decay in Peak mode or an averaged decay in
RMS mode).
 Gain-Q Couple Strength pop-up menu (extended parameter): Choose the amount of
Gain-Q coupling.