8
Table Of Contents
- Logic Express 8 Instruments and Effects
- Contents
- Introduction to the Logic Express Plugins
- Amp Modeling
- Delay
- Distortion
- Dynamics
- EQ
- Filter
- Imaging
- Metering
- Modulation
- Pitch
- Reverb
- Specialized
- Utility
- EVOC 20 PolySynth
- EFM1
- ES E
- ES M
- ES P
- ES1
- ES2
- The ES2 Parameters
- Tutorials
- Sound Workshop
- Sound Design From Scratch, Filter Settings, Digiwaves
- Three Detuned Sawtooth Oscillators and Unison Mode
- Extremely Detuned Monophonic Analog Sounds, Effects
- Clean Bass Settings With One Oscillator Only
- Distorted Analog Basses
- FM Intensity and Frequency
- Controlling FM Intensity by an Envelope and FM Scaling
- FM With Drive and Filter-FM
- FM With Digiwaves
- FM With Wavetables
- Distorted FM in Monophonic Unison
- FM With Unusual Spectra
- Slow and Fast Pulse Width Modulations With Oscillator 2
- Pulse Width Modulation With Two Oscillators, PWM Strings
- Ring Modulation
- Oscillator Synchronization
- First Steps in Vector Synthesis
- Vector Synthesis—XY Pad
- Vector Synthesis Loops
- Bass Drum With Self-Oscillating Filter and Vector Envelope
- Percussive Synthesizers and Basses With Two Filter Decay Phases
- Templates for the ES2
- Sound Workshop
- EXS24 mkII
- Learning About Sampler Instruments
- Loading Sampler Instruments
- Working With Sampler Instrument Settings
- Managing Sampler Instruments
- Searching for Sampler Instruments
- Importing Sampler Instruments
- Parameters Window
- The Instrument Editor
- Setting Sampler Preferences
- Configuring Virtual Memory
- Using the VSL Performance Tool
- External Instrument
- Klopfgeist
- Ultrabeat
- GarageBand Instruments
- Synthesizer Basics
- Glossary
- Index
224 Chapter 20 ES2
OscWaveB
The transitions between Digiwaves during a wavetable modulation are always smooth.
Depending on the modulation intensity, an additional OscWaveB target can be used to
continuously modulate the shape of the transitions from smooth to hard. It applies to
all Oscillators.
Osc1WaveB
If wavetable modulation is active for a Digiwave using Osc1Wav, you can use this target
to modulate the shape of the transition.
Osc1 FM mode: When compared with the hardwired Osc1-FM and the Osc1Wave
modulation target, the Osc1WaveB modulation target offers much higher FM
intensities.
Osc2WaveB
If wavetable modulation is active for a Digiwave using Osc2Wav, you can use this target
to modulate the shape of the transition.
Osc3WaveB
If wavetable modulation is active for a Digiwave using Osc3Wav, you can use this target
to modulate the shape of the transition.
SineLevl
SineLevl (Sine Level) allows modulation of the sine wave level of Oscillator 1, which can
be mixed directly into the input of the dynamic stage—without being affected by the
filters. The parameter defines the level of the first partial tone of Oscillator 1. See the
“Sine Level” section, on page 219.
OscLScle
OscLScle (Osc Level Scale) allows modulation of the levels of all three oscillators
simultaneously. A modulation value of 0 mutes all oscillators, while a value of 1 raises
the gain of the entire mix by 12 dB. The modulation is applied before the overdrive
stage, allowing for dynamic distortions.
Osc1Levl
Osc1Levl (Osc 1 Level) allows modulation of Oscillator 1’s level.
Osc2Levl
Osc2Levl (Osc 2Level) allows modulation of Oscillator 2’s level.
Osc3Levl
Osc3Levl (Osc 3Level) allows modulation of Oscillator 3’s level.
Cutoff 1
This target allows modulation of the Cutoff Frequency of Filter 1. See the “Cutoff and
Resonance” section, on page 214.