iPhone 13 Pro Max Repair Manual © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Contents Contents 3 Introduction Basics 6 Internal View 9 Screws 7 10 Orderable Parts Tools Safety 15 18 Battery Safety Broken Glass Procedures 20 21 First Steps SIM Tray 50 Bottom Speaker 22 54 62 67 Display Camera Taptic Engine Battery © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Introduction Introduction This manual includes technical instructions for replacing genuine Apple parts in iPhone and is intended for individual technicians with the knowledge, experience, and tools required to repair electronic devices. Important • • • • Read the entire manual first. If you’re not comfortable performing the repairs as instructed in this manual, don’t proceed. Always use the latest version of this document available at support.apple.com/manuals/ repair+manual.
iPhone 13 Pro Max Introduction Tools and parts Hardware tools Apple tools are designed to apply the appropriate heat, force, and torque during repairs, and to withstand high-volume professional use. • • • The heated display removal fixture softens adhesive to allow separation of the display from the enclosure. The fixture is used with a heated display pocket designed for the device’s specific dimensions.
iPhone 13 Pro Max Introduction System Configuration requires a strong Wi-Fi network capable of 1.0 Mbps download and upload speeds, with less than 400 ms latency and less than 2% packet loss. Estimated data usage to run System Configuration is 6–22 MB. The device must be running the latest version of iOS and not a beta version. Learn how to initiate the System Configuration process at support.apple.com/self-service-repair.
iPhone 13 Pro Max Internal View Internal View 1. Top speaker 10. Taptic Engine 3. Cameras 12. SIM reader 2. 4. 5. 6. 7. 8. 9. TrueDepth camera assembly Camera flex cable Battery adhesive tabs Battery Bottom speaker Lightning connector Bottom microphones © 2022 Apple Inc. All rights reserved. 11. Battery connector 13. Display/Multi-Touch connector 14. Logic board cowling 15. Logic board 16. Ambient light/proximity sensor connector 17.
iPhone 13 Pro Max Orderable Parts Orderable Parts Name Numbers Screws Battery 661-22294 — Bottom speaker 923-06648 923-05106 (1) lower right 923-06276 (3) lower left, upper left, upper right Camera 661-22293 — Camera cowling 923-06632 923-06266 (1) middle 923-06267 (1) upper right 923-06268 (3) lower left, lower right, left Display 661-22309 LL661-22309 (U.S.
iPhone 13 Pro Max Orderable Parts Name Numbers Screws Taptic Engine 923-06643 923-06263 (1) left 923-06635 (1) upper right (super screw) 923-06636 (1) lower middle Upper cowling 923-06639 923-06269 (1) upper left 923-06285 (2) lower left, lower right 923-06634 (1) upper right © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Screws Screws • • Warning Never reinstall a screw after it has been removed. Install only new screws. iPhone screw grooves are covered in adhesive that can’t be reused. Use only the torque driver indicated to install new screws during reassembly. Both overtightened screws and loose screws can damage parts. Note: You can use any torque driver to remove screws.
iPhone 13 Pro Max Tools Tools Tools with part numbers are available for purchase from the Self Service Repair Store. Tools without part numbers can be purchased from electronics supply retailers. 923-06622 6.7-inch back protective cover 923-04880 6.7-inch display protective cover 661-22310 6.7-inch heated display pocket 923-06597 6.7-inch repair tray 923-01092 Adhesive cutter 923-02657 Battery press Cut-resistant gloves 923-06601 Display adhesive press plate © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Tools ESD mat ESD-safe cleaning solution ESD-safe tweezers ESD wrist strap with clip or plug Ethanol wipes1 661-17619 Heated display removal fixture Heat-resistant gloves IPA wipes Nitrile or lint-free gloves 922-5065 Nylon probe (black stick) © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Tools Sand2 Sand container3 923-02066 Super screw bit 923-0248 Torque driver (black, 0.35 kgf cm) kit4 923-0448 Torque driver (blue, 0.65 kgf cm) 923-00738 Torque driver (gray, 0.55 kgf cm) 923-00105 Torque driver (green, 0.45 kgf cm) 1 2 3 4 Ethanol wipes must contain at least 90% ethanol and no additives except isopropyl alcohol.
iPhone 13 Pro Max Tools | Heated Display Removal Fixture Heated Display Removal Fixture Note: A rented heated display removal fixture may have different packaging than shown. If your fixture came with a USB cable, set the cable aside. This setup doesn’t require it. 1. Remove the fixture from the box. Then remove the packing Styrofoam. Caution Don’t lift the fixture by the knob. 2. Cut and remove the zip tie from the handle. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Tools | Heated Display Removal Fixture 3. Turn the top knob on the fixture counterclockwise to raise the suction cup. Remove the packing Styrofoam. 4. Turn the emergency stop knob clockwise until it clicks and protrudes from the stop guard. 5. Plug the power cord into the fixture. The fixture won’t turn on until you flip the switch on the back. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Battery Safety Battery Safety • • • • Warning This device contains a built-in lithium-ion rechargeable battery with soft battery cells. Battery safety is the number one concern when repairing a device with a built-in lithium-ion battery. Only technicians with the knowledge, experience, and tools required to repair electronic devices should replace a battery.
iPhone 13 Pro Max Battery Safety Warning How to handle a battery thermal event A battery thermal event is a rapid chemical chain reaction that occurs inside a battery cell. The energy stored in the battery is released suddenly, which can cause outgassing and fire. A battery thermal event can be triggered by physical damage to the battery, improper replacement or repair, or temperatures outside the battery’s operating range.
iPhone 13 Pro Max Battery Safety How to handle batteries Warning Fully discharge the battery before you begin a repair. A discharged battery is less susceptible to a battery thermal event. If you can’t determine the battery level, don’t repair the device. Perform the following steps to discharge the battery: • Disconnect all external cables. • Turn on the flashlight from the Lock Screen, in Control Center, or by asking Siri.
iPhone 13 Pro Max Broken Glass Broken Glass Warning iPhone displays and some back covers are made of glass. The glass could break if the iPhone is dropped on a hard surface, receives a substantial impact, or is crushed, bent, or deformed. Don’t attempt to remove chipped or cracked glass shards.
iPhone 13 Pro Max Broken Glass If the iPhone has any of the following conditions, stop the repair: • There’s no glass or insufficient glass for the protective cover to adhere to. • The iPhone doesn’t fit in the heated display pocket. • The protective cover doesn’t adhere to the iPhone. You can find a service option at support.apple.com/repair. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max First Steps First Steps Always perform the following steps before starting a repair: • Back up the iPhone. • Turn off the iPhone. • • • • • Discharge the battery fully. Disconnect all cables. Remove all cases and covers. Clear and clean your workspace. Put on an ESD wrist strap and attach it to a properly grounded ESD mat. Caution ESD (electrostatic discharge, or the release of static electricity) can damage electronic components.
iPhone 13 Pro Max SIM Tray SIM Tray Tools • SIM-eject tool or paper clip Removal 1. Find your model to locate the SIM tray. 2. Insert a paper clip or SIM-eject tool into the hole next to the SIM tray. 3. Push the paper clip or SIM-eject tool toward the enclosure to eject the SIM tray. 4. Remove the SIM tray. Reassembly 1. Press the SIM tray back into the side of the enclosure. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Display | Before You Begin Display Before You Begin • • Warning Read Battery Safety and follow workspace and battery handling guidelines before you begin. Read Broken Glass before you begin. Tools • 6.7-inch heated display pocket • Adhesive cutter • • • • • • • • • • • • • • 6.
iPhone 13 Pro Max • • Display | Before You Begin Caution To avoid damaging the lenses, don’t touch the TrueDepth camera assembly or nearby parts. Don’t touch the back of the display. Touching the back of the display may affect image quality. Important • • This procedure requires System Configuration. After you’ve completed all removal and reassembly steps, learn how to initiate the System Configuration process at support.apple.com/self-service-repair.
iPhone 13 Pro Max Display | Removal Removal 1. Use a torque driver and the Torx security bit to remove the two security screws, one from each side of the Lightning connector. Set aside the screws. 2. Flip the switch on the back of the heated display removal fixture to turn it on. The internal fan will turn on. Wait for a checkmark to appear on the screen. Note: If an error code appears on the screen, turn off the fixture and turn it back on. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Display | Removal 3. Take the iPhone out of the repair tray. Then insert the iPhone into the heated display pocket with the display faceup and the Lightning connector facing the bottom of the pocket. Important Ensure that the clamp on the side of the pocket is flipped up. 4. Flip down the clamp on the side of the pocket to lock the iPhone into place. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Display | Removal 5. Put on the heat-resistant gloves. Align the cutout on the bottom of the pocket with the rail on the fixture. Slide the pocket with the iPhone onto the rail on the fixture. Warning Don’t insert the pocket into the fixture without wearing the heat-resistant gloves. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Display | Removal 6. Slide the pocket into the fixture until you hear the pocket click into place. Note: The screen on the fixture will turn red and the timer will count down from 2 minutes while the pocket heats to the correct temperature. When the timer ends, the fixture will start to beep and the screen will turn green. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Display | Removal 7. Turn the knob on the fixture clockwise to lower the suction cup as close to the iPhone as possible without touching the iPhone. Caution To avoid damaging the iPhone, don’t turn the knob before the timer beeps. Note: The fixture will beep until the suction cup is lowered. 8. Grasp the handle and slide the suction cup straight out until the edge of the suction cup aligns with the bottom edge of the display.
iPhone 13 Pro Max Display | Removal 9. Turn the knob on the fixture clockwise to lower the suction cup onto the display (1). Then flip down the handle on the suction cup to secure the suction cup to the display (2). 10. Slowly turn the knob on the fixture counterclockwise until the display begins to separate from the enclosure. Important If you don’t see a gap between the display and the enclosure immediately, wait 30 seconds.
iPhone 13 Pro Max Display | Removal 11. Insert the edge of the adhesive cutter between the display and the enclosure. Run the cutter between the display and the enclosure to the right and left as shown until the display partially releases from the enclosure. Caution To avoid damaging the flex cables, don’t tilt up the bottom of the display more than 5 degrees. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Display | Removal 12. Flip up the handle to release the suction cup (1). Gently slide the flat end of the black stick under the edge of the suction cup to release it from the display (2). Caution Don’t turn the knob. Turning the knob may damage the flex cables. 13. Press the eject button on the side of the pocket to release the pocket from the fixture. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Display | Removal 14. Hold both sides of the pocket and slide it straight out of the fixture. 15. Flip up the clamp on the side of the pocket to release the iPhone (1). Hold the area outlined in blue and gently remove the iPhone from the pocket (2). 16. Place the iPhone into the repair tray with the display faceup and the Lightning connector facing the cutout. Remove the gloves. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Display | Removal 17. Slide the display slightly toward the bottom of the iPhone. 18. Insert the edge of the adhesive cutter into the top of the iPhone between the display and the enclosure. Hold the adhesive cutter at a 45-degree angle. Start at the middle and cut along the top and sides of the iPhone until the display is free. Caution To avoid damaging the flex cables, don’t tilt up the bottom of the display more than 5 degrees. 19.
iPhone 13 Pro Max Display | Removal 20. Tilt up the display toward the suction cups. Press the top and bottom edges of the display to secure it to the suction cups. • • Caution o avoid damaging the T enclosure or display, ensure that the internal display clips are released before you tilt up the display. on’t damage the flex D cables as you tilt up the display. Warning If the battery is dented, punctured, or otherwise damaged, stop the repair. You can find a service option at support.apple.
iPhone 13 Pro Max Display | Removal 21. Use a torque driver and the Micro stix bit to remove the three trilobe screws from the lower cowling (1) and the two trilobe screws from the upper cowling (2). Set aside the screws. 22. Use a torque driver and the JCIS bit to remove the two crosshead screws from the upper cowling (3). Hold the cowling in place while you remove the last screw. Set aside the screws. 23. Use ESD-safe tweezers to remove the lower cowling. Save the cowling for reassembly. 24.
iPhone 13 Pro Max Display | Removal 25. Use the black stick to lift the end of the battery flex cable off the connector (1). Caution You must disconnect the battery flex cable first to ensure that the iPhone remains turned off. 26. Use the black stick to lift the ends of the display flex cable (2) and ambient light sensor flex cable (3) off the connectors. 27. Hold the display by the edges. Pull the tabs on the suction cups to release them from the display.
iPhone 13 Pro Max Display | Removal 29. Use ESD-safe tweezers to pick up the adhesive. Then pull the adhesive to remove it from the enclosure. Repeat this process until all the adhesive is removed from the perimeter of the enclosure. Caution Don’t touch the TrueDepth camera assembly, grounding springs, or nearby parts. 30. Use ESD-safe tweezers to remove the grounding foam from the top of the enclosure above the TrueDepth camera. 31.
iPhone 13 Pro Max Display | Reassembly Reassembly 1. Inspect the internal display clips for damage before reassembly. Ensure that the internal display clips are at a 90-degree angle and aren’t bent or damaged. Important • • If the internal display clips are damaged, you may need to replace the display. If you’re installing a replacement display, peel the protective liner from the top and underside of it.
iPhone 13 Pro Max Display | Reassembly 4. Align the replacement display adhesive over the enclosure with the grounding foam on top. Ensure that the top holes of the adhesive align over the TrueDepth camera assembly. Caution Ensure that you’ve removed all adhesive residue from the display and the enclosure before you apply the replacement display adhesive. 5. The replacement display adhesive has a top release liner, a middle release liner, and a bottom release liner.
iPhone 13 Pro Max Display | Reassembly 6. Use the flat end of the black stick to gently adhere the grounding foam as shown. Caution Failure to adhere the grounding foam may damage the display, Wi-Fi, or TrueDepth camera. 7. Place the display adhesive press plate on top of the enclosure with the icon in the top right corner as shown. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Display | Reassembly 8. Position the repair tray with the iPhone in the display press. Pull down the lever until the display press locks. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Display | Reassembly 9. Wait until the timer on the display press beeps. Pull down the lever (1) and pull out the release knob (2). Then lift the lever (3). 10. Remove the repair tray from the display press and remove the press plate. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Display | Reassembly 11. Remove the left section on the top release liner first (1). Then remove the three sections running along the right (2), top (3), and bottom (4). Important Don’t remove the middle release liner yet. Top release liner 12. Insert the suction cups into the repair tray. 13. Align the left edge of the display with the left edge of the enclosure. Gently press along the edges of the display to secure it to the suction cups. 14.
iPhone 13 Pro Max Display | Reassembly 16. Use ESD-safe tweezers to position the lower cowling over the ends of the display and battery flex cables. 17. Use the black torque driver and Micro stix bit to install three new trilobe screws into the lower cowling. 18. Use ESD-safe tweezers to slide the tab of the upper cowling behind the ambient light sensor flex cable. Then lower the cowling over the end of the flex cable. 19.
iPhone 13 Pro Max Display | Reassembly 21. Peel the first strip of the middle release liner (1) clockwise, starting at the bottom right of the enclosure. Peel the second strip of the middle release liner (2) counterclockwise, starting at the bottom right of the enclosure. Then peel the third strip (3) clockwise, starting at the bottom left of the enclosure. Middle release liner 22. Inspect the display adhesive to ensure that it’s in the correct position and not damaged or wrinkled.
iPhone 13 Pro Max Display | Reassembly 26. Press all four corners of the display simultaneously. Then press along the edges of the display until you hear a click and the display is flush with the enclosure. Caution Ensure that the flex cables aren’t trapped between the display and the enclosure. Feel the edges of the display for variations or gaps. If the display isn’t flush, repeat all removal steps and check the flex cables for damage. Then repeat reassembly steps 1 through 26. © 2022 Apple Inc.
iPhone 13 Pro Max Display | Reassembly 27. Position the repair tray with the iPhone in the display press. Pull down the lever until the display press locks. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Display | Reassembly 28. Wait until the timer on the display press beeps. Pull down the lever (1) and pull out the release knob (2). Then lift the lever (3). 29. Remove the repair tray from the display press. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Display | Reassembly 30. Use the gray torque driver and Torx security bit to install two new security screws, one on each side of the Lightning connector. As you install the screws, press lightly on the display near the Lightning connector. Caution If the screws aren’t flush, remove and set aside the screws. Repeat step 30 to install another new set of screws. If the new screws still aren’t flush, repeat all removal and reassembly steps.
iPhone 13 Pro Max Bottom Speaker | Before You Begin Bottom Speaker Before You Begin Warning Read Battery Safety and follow workspace and battery handling guidelines before you begin. Remove the following part before you begin: • Display Tools • 6.7-inch repair tray • JCIS bit • • • • ESD-safe tweezers Nylon probe (black stick) Torque driver (blue, 0.65 kgf cm) Torque driver (gray, 0.55 kgf cm) Caution Avoid touching the grounding springs on the bottom speaker. © 2022 Apple Inc.
iPhone 13 Pro Max Bottom Speaker | Removal Removal 1. Place the enclosure in the repair tray with the Lightning connector facing the cutout. 2. Use a torque driver and the JCIS bit to remove the four crosshead screws from the bottom speaker. Set aside the screws. 3. Use ESD-safe tweezers to grasp the lower left screw hole and peel the bottom speaker away from the battery shim. Then remove the bottom speaker from the enclosure. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Bottom Speaker | Reassembly Reassembly 1. Rotate the repair tray. Ensure that the rubber gasket is positioned as shown. If the gasket is out of position, use ESD-safe tweezers to reposition it. 2. Rotate the repair tray. Then position the bottom speaker in the enclosure. 3. Use the gray torque driver and JCIS bit to install three new crosshead screws into the bottom speaker as shown. Press the bottom speaker down while you install the screws.
iPhone 13 Pro Max Bottom Speaker | Reassembly 4. Use the blue torque driver and JCIS bit to install one new crosshead screw into the bottom speaker. Reinstall the following part to complete reassembly: • Display © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Camera | Before You Begin Camera Before You Begin Warning Read Battery Safety and follow workspace and battery handling guidelines before you begin. Remove the following part before you begin: • Display Tools • 6.7-inch repair tray • JCIS bit • • • • • • ESD-safe tweezers Micro stix bit Nitrile or lint-free gloves Nylon probe (black stick) Torque driver (black, 0.35 kgf cm) Torque driver (gray, 0.
iPhone 13 Pro Max Camera | Before You Begin Important This procedure requires System Configuration. After you’ve completed all removal and reassembly steps, learn how to initiate the System Configuration process at support.apple.com/self-servicerepair. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Camera | Removal Removal 1. Place the enclosure in the repair tray with the Lightning connector facing the cutout. 2. Use a torque driver and the Micro stix bit to remove the four trilobe screws from the camera cowling. Hold the camera cowling in place as you remove the center screw. Set aside the screws. 3. Use a torque driver and the JCIS bit to remove the crosshead screw from the camera cowling. Set aside the screw. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Camera | Removal 4. Use ESD-safe tweezers to tilt up the camera cowling from the left side (1). Then slide the cowling tabs out of the slots on the right side of the enclosure (2). Save the cowling for reassembly. 5. Use ESD-safe tweezers to lift the ends of the two camera flex cables off the connectors. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Camera | Removal 6. Gently hold the camera flex cables together (1) and lift the cameras out of the enclosure (2). © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Camera | Reassembly Reassembly 1. Put on the gloves to prevent contamination of the camera lenses. Then hold the replacement cameras with the lenses facedown and remove the protective cover from the camera lenses. 2. Tilt the bottom edge of the cameras down and toward the battery as shown. Ensure that the camera flex cables are inside the channel between the battery and the camera well. 3. Position the cameras in the enclosure. 4.
iPhone 13 Pro Max Camera | Reassembly 5. Lightly press the cameras into the enclosure. 6. The camera cowling has tabs that fit into slots on the right side of the enclosure. Hold the cowling with ESD-safe tweezers and slide the cowling tabs into the slots. Then lower the cowling onto the cameras. • • 7. Caution Ensure that the screw cutouts in the camera cowling align with the screw holes and that the tabs are inside the slots in the enclosure.
iPhone 13 Pro Max Camera | Reassembly During System Configuration, you will perform LiDAR Scanner calibration. Prepare for calibration by reviewing the following steps: 1. Use a well-lit area containing objects of different shapes and sizes. 2. Sit or stand 1 to 2 feet from the objects. 3. Hold the device vertically and rest your elbow on your body to help stabilize your arm. 4. Start scanning by slowly panning back and forth to the left and right of the starting point.
iPhone 13 Pro Max Taptic Engine | Before You Begin Taptic Engine Before You Begin Warning Read Battery Safety and follow workspace and battery handling guidelines before you begin. Important Remove the following parts before you begin: • • Display Bottom speaker Tools • 6.7-inch repair tray • JCIS bit • • • • ESD-safe tweezers Nylon probe (black stick) Super screw bit Torque driver (blue, 0.
iPhone 13 Pro Max Taptic Engine | Removal Removal 1. Place the enclosure in the repair tray with the Lightning connector facing the cutout. 2. Use a torque driver and the super screw bit to remove the super screw from the Taptic Engine. Set aside the screw. 3. Use a torque driver and the JCIS bit to remove the two crosshead screws from the Taptic Engine. Set aside the screws. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Taptic Engine | Removal 4. Lift the end of the Taptic Engine flex cable off the connector. 5. Use ESD-safe tweezers to remove the Taptic Engine with the battery shim attached from the enclosure. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Taptic Engine | Reassembly Reassembly 1. Remove the adhesive release liner from the replacement battery shim. Then adhere the battery shim to the top edge of the Taptic Engine. 2. Use ESD-safe tweezers to position the Taptic Engine with battery shim in the enclosure. 3. Press the end of the Taptic Engine flex cable to the connector. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Taptic Engine | Reassembly 4. Use the blue torque driver and super screw bit to install one new super screw into the Taptic Engine (1). 5. Use the blue torque driver and JCIS bit to install two new crosshead screws into the Taptic Engine (2). Reinstall the following parts to complete reassembly: • • Bottom speaker Display © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Battery | Before You Begin Battery Before You Begin • • Warning A battery should be replaced only by individual technicians with the knowledge and experience to repair electronic devices. Improper battery replacement, improper handling of parts, or failure to follow the provided instructions could result in fire, injury, data loss, or damage to the device, parts, or other property. Read Battery Safety and follow workspace and battery handling guidelines before you begin.
iPhone 13 Pro Max Battery | Before You Begin Caution To avoid damaging the lenses, don’t touch the TrueDepth camera assembly or nearby parts. Important This procedure requires System Configuration. After you’ve completed all removal and reassembly steps, learn how to initiate the System Configuration process at support.apple.com/ self-service-repair. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Battery | Removal Removal 1. Place the enclosure in the repair tray with the Lightning connector facing the cutout. 2. Use ESD-safe tweezers to grasp the bottom right battery adhesive tab. Gently peel the adhesive tab away from the battery. Note: The battery has four adhesive tabs. Warning Don’t scrape or puncture the battery with the tweezers. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Battery | Removal 3. Hold down the iPhone. Use ESD-safe tweezers to continue peeling the adhesive tab from the battery. Important Peel the adhesive tab completely from the battery before twisting it around the tweezers. 4. Keep the tweezers close and parallel to the battery and twist until you see white adhesive strip on the tweezers. Important Don’t pull the tweezers until the white adhesive is wrapped around them. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Battery | Removal 5. Pull the tweezers toward the bottom of the iPhone and continue to twist the adhesive strip until you’ve removed the entire strip. Caution Don’t pull the adhesive strip against parts or screws. Important If the battery adhesive tab or strip breaks off and you can still see it, attempt to retrieve it with the tweezers. Wrap the tab or strip around the tweezers and repeat steps 4 and 5. If you can’t see the tab or strip, continue to step 6. 6.
iPhone 13 Pro Max 9. Hold down the iPhone. Use ESD-safe tweezers to gently peel one battery adhesive tab from the top of the battery. Then twist the tweezers to wrap the adhesive tab around them. Battery | Removal Battery | Removal Important Hold the tweezers close and parallel to the battery as you twist. 10. Keep the tweezers in the channel between the battery and the camera cowling. Continue to slowly twist the tweezers until you’ve removed the entire adhesive strip.
iPhone 13 Pro Max Battery | Removal 12. If all four battery adhesive strips were fully removed, continue to step 14. If at least one strip was fully removed, continue to step 13. Warning If all four strips were broken and can’t be retrieved, don’t forcibly pry the battery. Stop the repair. You can find a service option at support.apple.com/repair. Caution When using the black stick to remove the battery from the enclosure, don’t damage the flex cables.
iPhone 13 Pro Max Battery | Removal 14. Slightly lift the battery with the black stick just enough to grasp underneath the battery. Caution To avoid damage, don’t press the black stick on the edge of the enclosure as you lift the battery. 15. Remove the battery from the enclosure. Then inspect the enclosure for damage. If the enclosure is damaged, replace the iPhone. Warning If you can’t remove the battery, stop the repair. You can find a service option at support.apple.com/repair. © 2022 Apple Inc.
iPhone 13 Pro Max Battery | Reassembly Reassembly 1. Use ethanol wipes or IPA wipes on the area shown in blue to remove any remaining adhesive from the enclosure. Caution Don’t use ethanol wipes or IPA wipes on the areas outlined in red. Ethanol or isopropyl alcohol may damage the polyester film and wireless charging unit. Warning Inspect the enclosure for loose or extra screws and small parts, which can damage the battery and cause safety issues. 2. Reinstall the Taptic Engine. 3.
iPhone 13 Pro Max Battery | Reassembly 4. Peel the pink release liner from the underside of the replacement battery. Important Don’t remove the battery protective cover from the top of the battery yet. 5. Hold the battery over the enclosure with the protective cover faceup. Align the bottom of the battery with the Taptic Engine (1) and the left edge with the logic board (2). Then lower the battery into the enclosure. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Battery | Reassembly 6. The center of the repair tray has two slots. Position the repair tray and enclosure onto the battery press with the left slot over the pin as shown. 7. Flip down the red lever to lower the roller onto the battery. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Battery | Reassembly 8. Slide the repair tray back and forth through the battery press three times to adhere the battery to the enclosure. 9. Flip up the red lever. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Battery | Reassembly 10. Position the repair tray and enclosure onto the battery press with the right slot over the pin. 11. Flip down the red lever. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Battery | Reassembly 12. Slide the repair tray back and forth through the battery press three times to adhere the battery to the enclosure. 13. Flip up the red lever. © 2022 Apple Inc. All rights reserved.
iPhone 13 Pro Max Battery | Reassembly 14. Remove the repair tray from the battery press. 15. Hold the edges of the protective cover. Pull the release tabs on the protective cover to remove the cover from the battery. Important Don’t press the area over the tab you’re releasing. Reinstall the following part to complete reassembly: • Display Warning Gently shake the iPhone. If the battery sounds loose, remove the display and the battery.
