K Service Source AppleVision 1710AV/1710 Display AppleVision 1710AV Display AppleVision 1710 Display
K Service Source Hot Issues AppleVision 1710AV/1710 Display
Hot Issues Overview - 1 Overview This chapter is designed to highlight unique or highpriority product issues that you should be aware of before servicing this display. This chapter alerts you to important issues and provides links to other areas in the manual where more complete information can be found. This chapter is not intended to replace other parts of this manual; it merely provides a pointer to pertinent information in those chapters.
Hot Issues AppleVision 1710 Enhanced Customer Support Program (ECSP) AppleVision 1710 Enhanced Customer Support Program (ECSP) Has Expired (2/99) The Enhanced Customer Support Program (ECSP) that addressed a number of isolated quality issues with AppleVision 1710 and 1710AV Displays expired on December 31, 1998. .
Hot Issues AppleVision 1710/1710AV Repair Program Extended (8/98) - AppleVision 1710/1710AV Repair Program Extended (8/98) Overview Apple is extending the AppleVision 1710 and 1710AV Display Repair Program. Under this program, which now runs from August 1, 1998 through December 31, 1998, customers with AppleVision 1710 and 1710AV Displays that exhibit no video and/or no power symptoms may be eligible to receive repairs at no charge.
Hot Issues AppleVision 1710/1710AV Repair Program Extended (8/98) - Product Identification All AppleVision 1710 and 1710AV Displays that exhibit the no video and/or no power symptom and have serial numbers from SG522xxxxxx up to and including SG628xxxxxx are eligible for this program. Repair Strategy Refer to the latest update of the AppleVision 1710/1710AV Repair Program program notice on Service Source Online for complete details.
Hot Issues Revised Troubleshooting Chapter Features CRT/Video Board Pro- Revised Troubleshooting Chapter Features CRT/Video Board Procedures (3/98) The Troubleshooting chapter has been revised to include procedures for downloading setup parameters, adjusting the display after replacing the CRT/video board or the main deflection board, and diagnosing suspected hardware problems. The latest version of the Diagnostics utility called Display Service Utility (v4.2.
Hot Issues Revised Troubleshooting Chapter Features CRT/Video Board Proexpanded Troubleshooting chapter for the latest troubleshooting procedures; refer to the Diagnostics site of Service Source Online or the Service Source Companion CD (Diagnostic Utilities folder) for the Display Service Utility v4.2.1.
Hot Issues Focus Adjustment Might Be Necessary After Replacing the Main Focus Adjustment Might Be Necessary After Replacing the Main Deflection Board (10/97) Issue: After replacing the main deflection board on an AppleVision 1710 or 1710AV display, the screen focus might require adjustment. Solution: If the screen focus is poor after replacing a main deflection board, adjust the horizontal and vertical focus controls on the flyback transformer.
Hot Issues Black Screen, Distortion, or Misconvergence Caused by CRT Arc- Black Screen, Distortion, or Misconvergence Caused by CRT Arcing (6/97) Issue: On a limited number of AppleVision 1710 monitors, an internal arcing within the cathode ray tube (CRT) may reset some control values in the monitor's internal microcontroller chip. This can cause the screen to go blank, cause some geometry distortion, or cause the convergence to become intolerable.
Hot Issues Black Screen, Distortion, or Misconvergence Caused by CRT ArcSolution: In some cases simply using the power switch on the front panel of the monitor will eliminate the screen distortion. Otherwise, shut down the monitor and unplug the power cord and ADB cables from the back of the monitor. Count to ten. Then plug in the power cord and ADB cables. This action should remove all symptoms. If the blank screen symptom persists, contact Apple Technical Support.
K Service Source Basics AppleVision 1710AV/1710 Display
Basics Product Overview - 1 Product Overview The AppleVision 1710AV Display is a full-page, Trinitron color monitor that supports a variety of resolutions. The display includes sound and video support for multimedia application programs and advanced controls for accurate color rendering. The AppleVision 1710AV Display has a diagonal viewable image size of 16.1 inches.
Basics Product Overview - 2 The AppleVision 1710AV Display works with both Macintosh and IBM PC-compatible computers. For information on using the display with an IBM PC-compatible computer, refer to Part II (“Using the Display With Your IBM PCCompatible Computer”) in the User’s Guide.
Basics Product Overview - 3 Except for the speaker enclosure and microphone, the AppleVision 1710 Display shares the same features as the AppleVision 1710AV Display.
Basics Repair Issue: Display Service Utility - 4 Repair Issue: Display Service Utility The Display Service Utility (located in the Diagnostic Utilities folder on the Service Source Companion CD) has been updated for the April 1998 CD and Service Source Online (March 1998). The Display Service Utility is an application that you can use to display video test patterns, restore display parameter settings, and adjust the display after replacing a board.
Basics Repair Issue: Focus Adjustment after Replacing Main Deflection Repair Issue: Focus Adjustment after Replacing Main Deflection Board After replacing the main deflection board on an AppleVision 1710 or 1710AV display, the screen focus might require adjustment. If the screen focus is poor, adjust the horizontal and vertical focus controls on the flyback transformer.
K Service Source Specifications AppleVision 1710AV/1710 Display
Specifications Introduction - 1 Introduction Specifications information for this product can be found in this chapter and also in the Spec Database, which you can access in one of three ways: • Launch it directly by double-clicking the Apple Spec Database runtime alias at the top level of the Main Service Source CD. • Select “Apple Spec Database” from the Service Source dropdown main menu. • Click the Acrobat toolbar icon for the database, which is near the right end of the toolbar with the letters “SP.
Specifications Characteristics - 2 Characteristics Picture Tube Screen Resolution 17-in. Trinitron CRT (16.1-in. viewable image) Multiple scan Antistatic, antiglare surface treatment 0.26-mm dot pitch 640x480 at 60 Hz in VGA mode 640x480 at 66.67 Hz in Macintosh mode 800x600 at 60.31 Hz in VESA mode 800x600 at 75 Hz in VESA mode 832x624 at 74.55 Hz in Macintosh mode 1024x768 at 74.93 Hz in Macintosh mode 1024x768 at 60 Hz in VESA mode 1280x1024 at 60 Hz in VESA mode 1280x1024 at 75.
Specifications Characteristics - 3 Scan Rates Vertical refresh rate: 50–120 Hz Horizontal scan rate: 30–80 kHz Cable Connector 15-pin miniature D-type Input Signals Red, green, and blue signals; separate sync System Requirements System software version 7.
Specifications Characteristics - 4 AppleVision/CPU Compatibility List PowerBook 280 & 280ca 520, 520c 540, 540c Quadra, Centris, Performa 6200 5200 900, 950 800, 840AV 700 605, 610, 630, 650, 660AV LC 475 a.With MiniDock and DuoDock II.
Specifications Monitor Timings Characteristics - 5 640x480 Resolution @ 60 Hz 640x480 Resolution @ 66.67 Hz Horizontal Timing 1/H: 31.5 kHz Back Porch: 48 dots H SYNC: 96 dots Front Porch: 16 dots 1 H: 31.75 µs 1/dot: 25.175 MHz Horizontal Timing 1/H: 34.97 kHz Back Porch: 96 dots H SYNC: 64 dots Front Porch: 64 dots 1 H: 28.0 µs 1/dot: 30.24 MHz Vertical Timing 1 V: 16.7 ms Back Porch: 33 H V SYNC: 2 H Front Porch: 10 H Vertical Timing 1 V: 15.
Specifications Monitor Timings Characteristics - 6 800x600 Resolution @ 60.31 Hz 800x600 Resolution @ 75 Hz Horizontal Timing 1/H: 37.9 kHz Back Porch: 88 dots H SYNC: 128 dots Front Porch: 40 dots 1 H: 27.85 µs 1/dot: 40.000 MHz Horizontal Timing 1/H: 46.9 kHz Back Porch: 160 dots H SYNC: 80 dots Front Porch: 16 dots 1 H: 21.33 µs 1/dot: 49.5 MHz Vertical Timing 1 V: 16.58 ms Back Porch: 22 H V SYNC: 4 H Front Porch: 2 H Vertical Timing 1 V: 13.
Specifications Monitor Timings Characteristics - 7 832x624 Resolution @ 74.55 Hz 1024x768 Resolution @ 74.93 Hz Horizontal Timing 1/H: 49.7 kHz Back Porch: 224 dots H SYNC: 64 dots Front Porch: 32 dots 1 H: 20.1 µs 1/dot: 57.28 MHz Horizontal Timing 1/H: 60.24 kHz Back Porch: 176 dots H SYNC: 96 dots Front Porch: 32 dots 1 H: 16.6 µs 1/dot: 80 MHz Vertical Timing 1 V: 13.41 ms Back Porch: 38 H V SYNC: 3 H Front Porch: 2 H Vertical Timing 1 V: 13.
Specifications Monitor Timings Characteristics - 8 1024x768 Resolution @ 60 Hz 1280x1024 Resolution @ 60 Hz Horizontal Timing 1/H: 48.4 kHz Back Porch: 160 dots H SYNC: 136 dots Front Porch: 24 dots 1 H: 20.68 µs 1/dot: 65.0 MHz Horizontal Timing 1/H: 63.8 kHz Back Porch: 272 dots H SYNC: 112 dots Front Porch: 16 dots 1 H: 15.23 µs 1/dot: 110.25 MHz Vertical Timing 1 V: 16.66 ms Back Porch: 29 H V SYNC: 6 H Front Porch: 3 H Vertical Timing 1 V: 16.
Specifications Monitor Timings Characteristics - 9 1280x1024 Resolution @ 75.03 Hz Horizontal Timing 1/H: 79.976 kHz Back Porch: 248 dots H SYNC: 144 dots Front Porch: 16 dots 1 H: 12.5 µs 1/dot: 135 MHz Vertical Timing 1 V: 13.
Specifications Speakers (1710AV only) Characteristics - 10 Stereo, with ported (bass reflex) chamber design Maximum loudness: 92 dB SPL at 1 kHz at 0.
Specifications Controls and Ports - 11 Controls and Ports User Controls Front panel (1710AV): power, brightness, contrast, bass, treble, microphone on, volume, mute, and three on-screen control buttons Front panel (1710): power, brightness, contrast, and three onscreen control buttons Additional picture and sound controls available using the AppleVision Setup control panel (Macintosh users) or onscreen controls (IBM PC-compatible users) Automatic degauss at power-on; manual degauss by turning power switc
Specifications I/O Ports Controls and Ports - 12 Apple Desktop Bus (ADB): one input port and two pass-through output ports Headphone/Speaker (1710AV): One output port and two speaker ports Microphone (1710AV): One input port and one microphone port
Specifications Physical and Electrical - 13 Physical and Electrical Power Supply Size and Weight Monitor Stand Voltage: 100–240 VAC Frequency: 50–60 Hz Power: 130 W maximum Height: 19.7 in. (507 mm) Width: 15.8 in. (405 mm) Depth: 17.6 in. (452 mm) Weight (1710AV): 60 lb. (27 kg) Weight (1710): 50 lb. (22.
Specifications Environmental - 14 Environmental Temperature Humidity Operating: 50°F to 104°F (10°C to 40°C) Shipping: –4°F to +140°F (–40°C to +60°C) Storage: 32°F to 140°F (0°C to 60°C) Operating: 20% to 80%, noncondensing Shipping: 5% to 95%, noncondensing Storage: 5% to 90%, noncondensing Altitude Operating: 0 to 10,000 ft. (0 to 3,048 m) Transit: 0 to 35,000 ft.
K Service Source Troubleshooting AppleVision 1710AV/1710 Display
Troubleshooting General/ - 1 General The Symptom Charts included in this chapter will help you diagnose specific symptoms related to your product. Because cures are listed on the charts in the order of most likely solution, try the first cure first. Verify whether or not the product continues to exhibit the symptom. If the symptom persists, try the next cure. (Note: If you have replaced a module, reinstall the original module before you proceed to the next cure.
Troubleshooting First Checklist/ - 2 First Checklist Important: Many AppleVision 1710AV and 1710 display modules returned for repair are found to be fully operational. Read this checklist before you return a module, and prevent needless module replacement and unnecessary time delays. The AppleVision 1710AV/1710 Display is not compatible with all computers. This display works with both Macintosh and IBM PC-compatible computers. A video card may need to be installed to use this display with some computers.
Troubleshooting First Checklist/ - 3 A maladjusted screen can mimic the symptoms of main deflection board or CRT failures. By performing the adjustment procedures, you might determine if one or more of the adjustments is the cause of the problem. Variances in screen color and brightness are usually caused by the setup controls or the environment. Screen color purity over the entire screen is never perfect. CRT tolerances allow for some distortion.
Troubleshooting Symptom Charts/No Raster - 4 Symptom Charts Important: For procedures that require the monitor to be turned on, allow the monitor to warm up for approximately 20 minutes, unless instructed otherwise. Important: Ensure the latest version of Apple Display software (1.5.3 or later) is installed. (Apple Display software supersedes and replaces AppleVision software as of version 1.5.3.
Troubleshooting No raster (screen is black); power indicator light off Symptom Charts/Geometry - 5 1 2 3 4 5 No raster (screen is black) after Restart 1 2 3 Verify that monitor is connected to live power source, that power button is on, and that computer connected to display is turned on. Important: Be sure the ADB and video cables from the monitor are connected to the ports on the computer. Check that all internal cables are connected and that CRT/ video board is properly seated on CRT socket.
Troubleshooting Symptom Charts/Screen Color - 6 Screen Color Screen is one predominant color 1 2 3 4 5 Screen has color rainbow effect (bands of color across the screen) 1 2 3 4 Verify that CRT/video board is properly seated on CRT socket. Using Monitors & Sound control panel, click Recalibrate button (see the Adjustments chapter). If you have AppleVision software 1.5.
Troubleshooting Symptom Charts/Focus - 7 Focus Focus poor 1 2 3 4 5 6 Using the Monitors & Sound control panel, verify that convergence is set correctly. Maladjusted convergence gives the appearance of bad focus. Note: Convergence over entire screen is never perfect. Using the Display Service Utility (inside the Diagnostics Utilities folder on the Service Source Companion CD), select focus pattern.
Troubleshooting Center of screen remains blurry after adjusting focus and convergence Symptom Charts/Focus - 8 1 2 3 Use a standard hex tool to adjust H-Stat (lower left side of CRT/video board). If center-of-screen appearance is good, but top/bottom convergence is blurry, use a plastic adjustment tool to adjust the top and bottom convergence (back of CRT/video board). If screen is still blurry after adjusting convergence, one of the CRT socket wires may be improperly secured.
Troubleshooting Symptom Charts/Audio (1710AV only) - 9 Audio (1710AV only) The symptoms associated with a defective sound enclosure are relatively easy to diagnose. Following are typical symptoms of a defective audio system. However, some of these symptoms can also be caused by defective speakers, the built-in microphone, and connectors or cables that plug into the sound enclosure.
Troubleshooting Symptom Charts/Miscellaneous - 10 While in sleep mode, power indicator light randomly flashes and monitor powers up and shuts down every few seconds; speakers may emit clicking sound 1 Moving and clicking a Logitech mouse has no effect on screen, but keyboard input is accepted Some models of Logitech mice are incompatible with this display. Refer customers to Logitech for information on mouse compatibility and upgrades. The display is not at fault; do not replace it.
Troubleshooting Downloading Setup Parameters and Replacing the CRT/Video Downloading Setup Parameters and Replacing the CRT/Video Board* * Important: Some countries do not support replacement of the CRT/video board. Check the service strategy in your region before continuing this procedure. Caution: Before removing a defective CRT/video board, check the monitor serial number.
Troubleshooting Downloading Setup Parameters and Replacing the CRT/Video Duplicate the Parameter Settings File 1 2 3 4 5 Locate the Parameter Settings 1710 file, but do not move or rename it. Beside the Parameter Settings 1710 file create a new folder. Name the new folder Parameter File Backup. Hold down the option key and drag the Parameter Settings 1710 file onto the Parameter File Backup folder. Shut down the monitor. Unplug the power cord.
Troubleshooting Adjusting the Display after Replacing the CRT/Video Board*/ Adjusting the Display after Replacing the CRT/Video Board* * Important: Some countries do not support replacement of the CRT/video board. Check the service strategy in your region before continuing this procedure. Caution: Perform this procedure only after you’ve replaced the CRT/video board and uploaded the parameter settings. After replacing the CRT/video board, some adjustment is necessary.
Troubleshooting Adjusting the Display after Replacing the CRT/Video Board*/ Recalibrate White Points Caution: If the video cable is connected to a third-party video card that uses proprietary color calibration drivers, you might need to disable the drivers to use the AppleVision color calibration functions. 1 After you’ve rewritten the file, as instructed in “Upload Parameter Settings,” restart the system. 2 Open Monitors & Sound and select Color.
Troubleshooting Adjusting the Display after Replacing the Main Deflection Board/ Adjusting the Display after Replacing the Main Deflection Board After replacing the main deflection board, perform the following adjustments for all three Macintosh modes (screen resolutions): • 640x480 at 67 Hz • 832x624 at 75 Hz • 1024x768 at 75 Hz 1 Using the control strip (or the Monitors control panel), select 1024x768, the highest of the three Macintosh screen resolutions.
Troubleshooting Adjusting the Display after Replacing the Main Deflection Board/ 5 6 7 If necessary, repeat step 4 for the best overall focus. Check the screen to see if any minor geometry adjustments are necessary. If so, shut down the monitor and unplug the power cord. Install the jumper on the CRT/video board. Reattach the power cord. Restart the computer. Open the Display Service Utility and select AppleVision 1710/ 1710AV pattern selections.
Troubleshooting Checking High Voltage/Recalibrate White Points - 17 Checking High Voltage This high-voltage check is a required procedure for some of the symptoms in this chapter. After checking high voltage, return to the symptom chart, if necessary. Caution: Do not attempt this procedure without the Apple highvoltage probe (Apple part number 076-0392). Use only the Apple high-voltage probe; other high-voltage probes will not give accurate readings for this procedure.
Troubleshooting AppleVision Recovery Utility for Malfunction During Startup or AppleVision Recovery Utility for Malfunction During Startup or Recalibration Important: Disregard the rest of this section if you are using Apple Display software 1.5.3 or later. With version 1.5.3 or later, the AppleVision Recovery Utility is built in. To operate the built-in recovery function, ensure the monitor’s video and ADB cables are connected to the computer.
Troubleshooting AppleVision Recovery Utility for Malfunction During Startup or Using the AppleVision Recovery Utility To perform the recovery procedure, you need • Macintosh computer that can support two monitors (unless you have Symptom Set 2) • Malfunctioning AppleVision 1710 or 1710AV monitor • Known-good monitor (any model) • AppleVision Recovery Utility application located on the Service Source Companion CD: Diagnostics Utilities folder • AppleVision Setup control panel application installed on the
Troubleshooting AppleVision Recovery Utility for Malfunction During Startup or 6 7 Recalibrate the 1710(AV) monitor by clicking the recalibrate button. The screen should recalibrate successfully and return to an active raster. • If the recalibration is successful and the screen returns to an active raster, the monitor is recovered and no further service is required.
Troubleshooting Diagnosing A Suspected Hardware Problem/Using the AppleVision Diagnosing A Suspected Hardware Problem After ruling out other possible cures (that is, you have already checked cable connections, power, AppleVision software, and other possible front-of-screen cures), use the following procedure to help determine and resolve hardware problems. (See the flowchart at the end of this chapter for a simplified depiction of this process.
Troubleshooting Diagnosing A Suspected Hardware Problem/Using the AppleVision 7 If a dialog box appears that says the Display Service Utility (DSU) is unable to communicate with the display, then remove the monitor housing, and use a multimeter to measure the voltage between chassis ground and resistor RL1 on the end closest to capacitor CP17 on the main deflection board: • If the voltage measures 11.5 V to 12.
Troubleshooting Diagnosing A Suspected Hardware Problem/Using the AppleVision 8 If the Create File process finishes successfully, click Adjust Geometry. Clicking this button causes the DSU to automatically verify EHT (high voltage). Use a probe to measure the high voltage. (Refer to “Checking High Voltage” in this chapter.) • If the high voltage is okay, replace the CRT/video board and adjust the display (see “Adjusting the Display after Replacing the CRT/Video Board” in this chapter).
Troubleshooting Diagnosing A Suspected Hardware Problem/Using the AppleVision Start Open DSU and click Create File. DSU able to communicate with display (Create File process successful) ? No Measure voltage between chassis ground and RL1 (390 Ohm, pin closest to CP17). Yes Click Adjust Geometry. Adj.HV according to spec in Service Source. High voltage OK ? Voltage measures 11.5 to 12.5 V ? No Yes No Replace MDB. Yes Replace CRT/video board.
K Service Source Take Apart AppleVision 1710AV/1710 Display
Take Apart Microphone Assembly/Blank Plate - 1 Microphone Assembly/Blank Plate No preliminary steps are required before you begin this procedure. Note: The microphone assembly is on the 1710AV display; the blank plate is on the 1710 display. To protect the microphone assembly or blank plate, remove it before removing the sound enclosure or rear housing.
Take Apart Microphone Assembly/Blank Plate - 2 1 2 Place a jeweler’s screwdriver in the microphone assembly slot. Press the screwdriver down and toward the bezel to release a tab that holds the microphone to the bezel and rear housing. Grasp the microphone assembly with your other hand, and tilt it up and away from the monitor bezel.
Take Apart Microphone Assembly/Blank Plate - 3 3 Disconnect the microphone cable and remove the microphone assembly.
Take Apart Sound Enclosure (1710AV only) - 4 Sound Enclosure (1710AV only) Before you begin, remove the microphone assembly.
Take Apart Sound Enclosure (1710AV only) - 5 1 Place the monitor upside down on a protective pad.
Take Apart Sound Enclosure (1710AV only) - 6 2 Peel off the two adhesive disk screw covers. Stick them beside the screw holes. Replacement Note: After reinstalling the sound enclosure, replace the adhesive disk screw covers. They help maintain the sound integrity of the speaker chamber.
Take Apart Sound Enclosure (1710AV only) - 7 3 Use a long T-15 torx driver to loosen (but not remove) the four corner screws. Important: Do not remove the captive screws; they are held in place by rubber grommets inside the sound enclosure.
Take Apart Sound Enclosure (1710AV only) - 8 4 5 6 Tilt up the sound enclosure, away from the front of the monitor. While holding the sound enclosure up, disconnect • Connector at BA9 on the sound board (white wires) • 2-pin connector at BA10 on the sound board (gray wire) Important: Read the following Caution before removing other connections.
Take Apart Sound Enclosure (1710AV only) - 9 7 Caution: Pins HM1 and HM2 on the intermediate board are difficult to see. With the monitor upside down, the pins point straight down. To avoid bending the pins, use needlenose pliers to pull the connectors straight down and off the pins.
Take Apart Sound Enclosure (1710AV only) - 10 8 Lift the sound enclosure straight up and away from the monitor.
Take Apart Sound Enclosure Bezel (1710AV only) - 11 Sound Enclosure Bezel (1710AV only) Before you begin, remove the following: • Microphone assembly • Sound enclosure
Take Apart Sound Enclosure Bezel (1710AV only) - 12 1 2 If you see glue where the bezel and the speaker chamber meet, cut through the glue with a sharp knife. With the bezel facing you, place your thumbs on the notched top edges and pull the bezel up and toward you to release the tabs.
Take Apart Sound Enclosure Bezel (1710AV only) - 13 3 4 Disconnect the cable at BA3 from the sound board. Unsolder the black wire that is soldered to the rearmost end of component RA87 on the sound board. Note: On some units the black wire may not be soldered to RA87. If not, look for a single black wire coming from the bezel and connecting to the sound board. Disconnect the wire from the sound board.
Take Apart Sound Enclosure Bezel (1710AV only) - 14 5 Remove the three T-8 torx screws from the sound control board.
Take Apart Speakers (1710AV only) - 15 Speakers (1710AV only) Before you begin, remove the following: • Microphone assembly • Sound enclosure • Sound enclosure bezel
Take Apart Speakers (1710AV only) - 16 1 Disconnect speaker wires BA5 and BA6 from the sound board. Replacement Note: The speaker wires must cross each other. So when the front of the sound enclosure is facing you, the left speaker wire connects to the right connector at BA5, and the right speaker wire connects to the left connector at BA6. When replacing a speaker, route the wires through the guides on the speaker chamber.
Take Apart Speakers (1710AV only) - 17 2 Remove the four T-15 torx speaker screws. Caution: When replacing a speaker, do not overtighten the screws.
Take Apart Audio Cable (1710AV only) - 18 Audio Cable (1710AV only) Before you begin, remove the following: • Microphone assembly • Sound enclosure
Take Apart Audio Cable (1710AV only) - 19 1 2 Disconnect the audio cable from connector BA4 on the sound board. Lift the cable from the plastic guides and from the slot in the sound enclosure.
Take Apart Sound Board (1710AV only) - 20 Sound Board (1710AV only) Before you begin, remove the following: • Microphone assembly • Sound enclosure • Audio cable
Take Apart Sound Board (1710AV only) - 21 1 Disconnect from the sound board • Connector at BA3 • 2-pin connector at BA5 • 2-pin connector at BA6 Replacement Note: The speaker wires must cross each other. So when the front of the sound enclosure is facing you, the left speaker wire connects to BA5, and the right speaker wire connects to BA6.
Take Apart Sound Board (1710AV only) - 22 2 3 Remove the four T-15 torx screws from the sound board. Lift the board off of the sound enclosure. Replacement Note: Due to connector changes on the latest revision of the sound and intermediate boards, when you are replacing a sound board, you must also replace the intermediate board. The original sound board is no longer available.
Take Apart Bottom Housing (1710 only) - 23 Bottom Housing (1710 only) Bottom Housing No preliminary steps are required before you begin this procedure. Warning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety. ± 1 Place the monitor face down on a protective pad.
Take Apart Bottom Housing (1710 only) - 24 2 3 Screws Position the tilt-swivel base sideways and so it is resting over a table edge. Slide the tilt-swivel base down and remove the two T-15 torx screws above the tiltswivel base.
Take Apart Bottom Housing (1710 only) - 25 4 Screws Slide the tilt-swivel base up and remove the two T-15 torx screws below the base.
Take Apart Bottom Housing (1710 only) - 26 5 Rear Housing 6 7 8 HM1 BH1 Bottom Housing Tilt the bottom housing away from the rear housing. Disconnect the 4-pin connector at BH1 on the ADB board. Disconnect the singlepin connector at HM1 on the intermediate board. Remove the bottom housing.
Take Apart ADB Board (1710 only) - 27 Tab ADB Board (1710 only) Before you begin, remove the bottom housing. Note: The ADB board consists of two boards joined together with a cable and soldered connections. 1 2 ADB Board Tab Press and hold the two tabs away from the ADB board. Tilt the board up from the bottom housing to release it.
Take Apart ADB Board (1710 only) - 28 Replacement Note: Before securing the board tabs, position the ADB board so the plastic pins on the bottom housing line up with the holes in the board.
Take Apart Rear Housing - 29 Rear Housing Before you begin, remove the following: • Microphone assembly or blank plate • Sound enclosure (1710AV display) This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety.
Take Apart Rear Housing - 30 Important: You must remove the microphone assembly or blank plate and the sound enclosure before removing the rear housing. 1 2 With the monitor face down on a protective pad, remove the two T-15 torx screws. Locate the four screw covers.
Take Apart Rear Housing - 31 3 4 5 Caution: To avoid damaging the plastic housing or screw cover, don’t use a screwdriver or other metal tool. With one hand, press down on the tip of the screw cover, causing the screw cover to bow outward from the screw channel. Pull out the screw cover with your other hand. Repeat steps 3 and 4 for the remaining three screw covers.
Take Apart Rear Housing - 32 6 7 8 Remove the four T-15 torx screws. Where the top part of the rear housing meets the bezel, pull up and out on the arched opening (at the microphone assembly/blank plate area) to release the rear housing tabs from the bezel. With both hands on the rear housing, lift it off the bezel. Route the video cable through the housing opening.
Take Apart CRT/Video Board - 33 CRT/Video Board Before you begin, • Remove the microphone assembly/blank plate • Remove the sound enclosure (1710AV only) • Remove the rear housing • Discharge the CRT • Download the setup parameters if replacing the CRT/video board with a new board (refer to the Troubleshooting chapter) Caution: To avoid loss of data, you must download the display parameter settings
Take Apart CRT/Video Board - 34 before replacing the CRT/video board with a new board. However, you do not have to download the setup parameters if you are removing the board for another procedure and will install the same board. This product contains high voltage and a highvacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety. ±Warning: Caution: Never use a grounding wriststrap until after discharging the CRT.
Take Apart CRT/Video Board - 35 After discharging the CRT, 1 2 Remove the anode cap. With needlenose pliers, disconnect the long braided CRT ground cable.
Take Apart CRT/Video Board - 36 3 Disconnect • Short braided ground cable • BV14 (black and blue wires) • BV15 (red and brown wires • BV16 (with ferrite bead) • BV2 (ribbon cable) • Copper tape (or other connection between flyback transformer shield and CRT/video board)
Take Apart CRT/Video Board - 37 4 5 6 Disconnect these cables: • BV12 (ribbon cable) • BS6 (5-pin connector next to BV12) Remove the single Phillips screw from the metal shield on top of the CRT/video board. Remove the metal shield.
Take Apart CRT/Video Board - 38 7 8 Disconnect the video cable at • BV4 • BV3 Remove the Phillips screw that attaches the video cable clip to the CRT/video board.
Take Apart CRT/Video Board - 39 9 Loosen the mounting screw on the metal ring clamp that holds the CRT/video board to the CRT neck.
Take Apart CRT/Video Board - 40 10 Caution: Twisting, bending, or applying force to the CRT/video board could damage the neck of the CRT. With a gentle side-toside motion, ease the CRT/video board off the neck of the CRT until it clears the neck pins.
Take Apart CRT/Video Board - 41 11 With the red and white flyback transformer wires still attached, set the CRT/video board on the table. 12 Remove the three Phillips screws from the dark gray neck piece. 13 Press the tab and slide the plastic piece to the left and off of the CRT/ video board.
Take Apart CRT/Video Board - 42 14 While holding, but not pulling, the red and white wires, use a jeweler’s flat-blade screwdriver to tilt up the wire locks. Do not remove the wire locks from the CRT socket. Replacement Note: Place the wires in the correct location as shown: red wire in the right wire lock and the white wire in the left wire lock. Feel them touch the bottom of the CRT socket before securing them with the wire locks.
Take Apart Main Deflection Board - 43 Main Deflection Board Before you begin, • Remove the microphone assembly/blank plate • Remove the sound enclosure (1710AV only) • Remove the rear housing • Discharge the CRT • Remove the CRT/video board This product contains high voltage and a high-vacuum picture tube.
Take Apart Main Deflection Board - 44 Bulletins/Safety. Caution: Never use a grounding wriststrap until after discharging the CRT. 1 2 Disconnect two-wire cable BP2 (black and white wires) from the main deflection board.
Take Apart Main Deflection Board - 45 3 4 5 Place the monitor face down on a padded surface. Remove the six Phillips screws that secure the chassis to the CRT frame. Lift the main deflection board chassis straight off the CRT frame.
Take Apart Main Deflection Board - 46 6 Screw Screw Screw at HL7 Remove the following ground lug Phillips screws: • Green wire on top chassis flange • Black wire on top chassis flange • Black wire at HL7
Take Apart Main Deflection Board - 47 7 8 Main Deflection Board Screw Screw Remove the Phillips screw on the corner of the board next to the heatsink for DL6. Remove the Phillips screw that attaches the heatsink to the right side of the chassis.
Take Apart Main Deflection Board - 48 9 Remove the Phillips screw that secures the power receptacle to the board and chassis. 10 Being careful not to damage the plastic standoffs between the board and the chassis, slide the board forward to release it from the chassis standoffs and hooks. 11 Lift the board up and out of the chassis. Hook Chassis Screw Main Deflection Board 12 Remove the video cable (see “Video Cable and Strain Relief”).
Take Apart Main Deflection Board - 49 Replacement Note: The main deflection board chassis includes a label with the serial number for the entire monitor. So before returning a main deflection board, remove and retain the video cable and chassis. You will need to install the original video cable and chassis on the new board. Chassis Label Caution: Do not replace the main deflection board chassis as a complete assembly or you will lose the monitor’s original serial number.
Take Apart Main Deflection Board - 50 Replacement Note: After replacing the main deflection board on an AppleVision 1710 or 1710AV display, the screen focus might require adjustment. If the screen focus is poor, adjust the horizontal and vertical focus controls on the flyback transformer. For complete instructions, refer to the Focus symptom in the Troubleshooting chapter.
Take Apart Intermediate Board - 51 Intermediate Board Important: Service data indicates this board rarely fails.
Take Apart Intermediate Board - 52 This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety. ±Warning: Caution: Never use a grounding wriststrap until after discharging the CRT.
Take Apart Intermediate Board - 53 1 2 3 Remove the two Phillips screws. Disconnect • 10-pin connector at BM4 • 4-pin connector at BM5 Lift the intermediate board off of the chassis. Replacement Note: Due to recently revised connectors on the intermediate and sound boards, when you are replacing a sound board, you must also replace the intermediate board.
Take Apart Video Cable and Strain Relief - 54 Video Cable and Strain Relief Before you begin, • Remove the microphone assembly/blank plate • Remove the sound enclosure (1710AV only) • Remove the rear housing • Discharge the CRT This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety.
Take Apart Video Cable and Strain Relief - 55 Caution: Never use a grounding wriststrap until after discharging the CRT. 1 2 Remove the single Phillips screw from the metal shield on top of the CRT/video board. Remove the metal shield.
Take Apart Video Cable and Strain Relief - 56 3 4 5 Disconnect the video cable at • BV4 • BV3 Remove the Phillips screw that attaches the video cable clip to the CRT/video board. Refer to “CRT/Video Board” in this chapter to remove the CRT/video board.
Take Apart Video Cable and Strain Relief - 57 6 7 Remove the Phillips screw from the metal chassis. Lift the strain relief straight out of the chassis slot.
Take Apart On-Screen Display Board - 58 On-Screen Display Board Before you begin, • Remove the microphone assembly/blank plate • Remove the sound enclosure (1710AV only) • Remove the rear housing • Discharge the CRT • Remove the CRT/video board • Remove the main deflection board
Take Apart On-Screen Display Board - 59 This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety. ±Warning: Caution: Never use a grounding wriststrap until after discharging the CRT. 1 With the CRT face-down on a padded surface, remove the four 5/16inch hex screws.
Take Apart On-Screen Display Board - 60 2 Lift the metal frame straight off of the bezel.
Take Apart On-Screen Display Board - 61 3 4 Use a 9/64-inch hex key to remove the four screws holding the onscreen control boards to the front bezel. Lift the boards, including their plastic holders, straight up from the bezel.
Take Apart Front Bezel - 62 Front Bezel Before you begin, • Remove the microphone assembly/blank plate • Remove the sound enclosure (1710AV only) • Remove the rear housing • Discharge the CRT • Remove the CRT/video board • Remove the main deflection board
Take Apart Front Bezel - 63 This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety. ±Warning: Caution: Never use a grounding wriststrap until after discharging the CRT. 1 With the CRT face-down on a padded surface, remove the four 5/16inch hex screws.
Take Apart Front Bezel - 64 2 Lift the metal frame straight off the bezel.
Take Apart Front Bezel - 65 3 Using both hands, lift the CRT off of the bezel.
Take Apart Front Bezel - 66 Replacement Note: Route the cables as shown when replacing the bezel.
K Service Source Adjustments AppleVision 1710AV/1710 Display
Adjustments Introduction to AppleVision Setup Control Panel - 1 Introduction to AppleVision Setup Control Panel You can adjust the screen image using the buttons on the front of the display or you can use the AppleVision Setup Control panel. Most of the procedures in this chapter require use of the AppleVision Setup control panel. Before you begin, make sure you have installed the Macintosh software and have connected the monitor cable’s ADB connector to your computer’s ADB port.
Adjustments Introduction to AppleVision Setup Control Panel - 2 From the AppleVision 1710AV Setup control panel, you can select four main buttons: Display, Geometry, Color, and Sound.
Adjustments Brightness and Contrast - 3 Brightness and Contrast Before you begin, install the AppleVision Setup software. O Z ¤ ® Contrast and Brightness Controls Note: There are two ways to adjust the brightness and contrast. You can use the controls on the right side of the front panel, or you can use AppleVision Setup controls.
Adjustments Brightness and Contrast - 4 Brightness Brightness Controls O Z ¤ ® To use the front panel brightness controls, • Press the down button to decrease the brightness. • Press the up button to increase the brightness.
Adjustments Brightness and Contrast - 5 Contrast Contrast Controls O Z ¤ ® To use the front panel contrast controls, • Press the down button to decrease the contrast. • Press the up button to increase the contrast.
Adjustments Brightness and Contrast - 6 Using AppleVision Setup To use AppleVision Setup to adjust brightness and contrast, Control Buttons O Z ¤ ® 1 Press any control button to open the AppleVision Setup control panel.
Adjustments Brightness and Contrast - 7 2 3 Display Button Lowest Setting Highest Setting Slider Control (Shows Current Setting) Click the Display button. Drag the slider controls left or right to decrease or increase the brightness and contrast.
Adjustments Geometry - 8 Geometry 1 Geometry Button 2 Press any control button to open the AppleVision Setup control panel. Click the Geometry button.
Adjustments Geometry - 9 Height/Width Pointer Screen Rectangle 1 Click Height/Width. 3 Drag the left or right side of the screen rectangle to change the width. 2 4 Click to Adjust Screen Geometry Click to Restore The Default Settings Move the pointer over the screen rectangle in the picture of the display. Drag the top or bottom edge of the screen rectangle to change the height.
Adjustments Geometry - 10 Click to Decrease Image Height Note: Instead of dragging the screen rectangle, you can adjust height and width by clicking the arrow buttons for incremental movement. Normal height and width leaves a black border of approximately 1/2-inch around the screen image.
Adjustments Geometry - 11 Position (Centering) Position Button 1 Click Position. 3 Drag the screen rectangle to center the image. 2 Move the pointer over the picture of the display. Note: Instead of dragging the screen rectangle, you can also adjust height and width by clicking the arrow buttons for incremental movement.
Adjustments Geometry - 12 Pincushion Pincushion Button 1 Click Pincushion. 3 Drag the left or right side of the screen rectangle to adjust the image. 2 Screen Rectangle Move the pointer over the picture of the display. Note: Instead of dragging the screen rectangle, you can adjust the shape of the image by clicking the arrow buttons for incremental movement.
Adjustments Geometry - 13 Rotating 1 Click Rotate. 3 Drag the screen rectangle clockwise or counterclockwise to rotate the image. 2 Rotate Button Move the pointer over the picture of the display. Note: Instead of dragging the screen rectangle, you can rotate the image by clicking the arrow buttons for incremental movement.
Adjustments Geometry - 14 Convergence 1 If you want to adjust the RGB color convergence, click the Convergence button. A Convergence Control window appears. Note: When you adjust convergence, refer to the center of the screen on the grid outside the Convergence Control window. If necessary, move the window away from the center of the screen.
Adjustments Geometry - 15 Click to Move the Red Signal Down and the Blue Signal Up Click to Move the Red Signal to the Left and the Blue Signal to the Right Click to Move the Red Signal to the Right and the Blue Signal to the Left Click to Move the Red Signal Up and the Blue Signal Down 2 Click the arrow buttons to adjust convergence. Adjust convergence for the overall best screen color clarity. Note: The active range for the horizontal convergence controls varies from unit to unit.
Adjustments Geometry - 16 3 If the horizontal controls seem stuck, move the controls in one direction a large extent and if no affect is seen, move them in the other direction a large extent until a change is detected. Moving back and forth in small increments will have no affect until the controls are moved into the active range. Click OK to save your convergence changes and close the Convergence Control window.
Adjustments Geometry - 17 Overscan Note: Overscan is typically used when viewing a movie or when you want the screen image to span the entire screen area (exceeding the limit of the raster). 1 Click to Turn Overscan On or Off To turn overscan on, click On. Important: When overscan is on, you cannot adjust screen geometry or convergence, and you might not be able to choose commands from the menu bar at the top of the screen.
Adjustments Geometry - 18 2 Click to Turn Overscan On or Off To turn overscan off, click Off, and the screen image returns to its previous size.
Adjustments Geometry - 19 Factory Settings Click to Recall Factory Settings Important: Recalling the factory settings resets only the four geometry controls and convergence. The screen image returns to the factory preset levels of geometry (height/width, position, pincushion, rotation) and convergence for the current screen resolution. Adjustments you make in the Display, Color, or Sound windows are not reset. Click Recall Factory Settings.
Adjustments Color - 20 Color 1 Color Button 2 Press any control button to open the AppleVision Setup control panel. Click the Color button.
Adjustments Color - 21 Setting a White Point 1 Standard White Points 2 Pop-Up Menu of Custom White Points Recalibrate Button Click one of the standard white points: • D50=graphic arts standard • 6500=midday sun • 9300=Macintosh displays and highdefinition TV Note: Changes won’t take effect until you click Recalibrate. Click Recalibrate.
Adjustments Create Custom White Point Button Color - 22 Creating a Custom Kelvin White Point 1 Click Create Custom White Point button.
Adjustments Click to Create a White Point Using Kelvin Temperatures Color - 23 Drag to Select a Kelvin Temperature 2 3 4 Click to Save a Custom White Point 5 Click Kelvin if you want to use Kelvin temperatures. Drag the slider control to select the temperature (4100 to 9300). Click Save, and name the custom white point. The name appears in the White Point Custom menu. Click Recalibrate.
Adjustments Create Custom White Point Button Color - 24 Creating a Custom CIE Color Space White Point 1 Click Create Custom White Point button.
Adjustments Color - 25 2 Click to Create a White Point Using 1931 CIE Standards Click to Create a White Point Using 1976 CIE Standards Click • xy (1931 CIE) if you want to use 1931 CIE standards • u’v’ (1976 CIE) if you want to use 1976 CIE standards
Adjustments Color - 26 3 Enter Values to Create a Custom White Point 4 5 1931 CIE Color Space Drage Crosshairs to Create a Custom White Point Drag crosshairs to create custom white point. Note: Instead of dragging the crosshairs, you can enter values in the fields to the right of the crosshairs. Click Save, and name the custom white point. Click Recalibrate.
Adjustments Color - 27 Adjusting for Ambient Light 1 O Z Ambient Light Tool ¤ ® Locate the ambient light tool that came with the display. Important: Store the ambient light tool in its protective sleeve when you’re not using it. If the gray color fades, you’ll get incorrect ambient light readings.
Adjustments White Point Color - 28 Set Ambient Light Button 2 Click Set Ambient Light button. Important: The screen’s color depth must be set to “Millions of Colors.” Refer to the section called “The Control Strip” in this chapter.
Adjustments Color - 29 3 Color Sample O Z ¤ ® Hold the ambient light tool against the display face, over the square color sample.
Adjustments Color - 30 4 Brightness Slider Color Triangle 5 Picker 6 Color Sample 7 Drag the picker in the color triangle until the color sample is similar to the gray color on the ambient light tool. Drag the brightness slider until the color sample matches the ambient light tool exactly. Click Save, and name the new setting. The name appears in the Ambient Light Custom menu. Click Recalibrate.
Adjustments Color - 31 Adjusting Gamma Curve Important: The gamma value you select depends on the image you’re displaying. Color images with important details in highlights or shadows need a different gamma value than standard images. 1 Click to Select a Standard Gamma Value Click to Leave Gamma Value Uncorrected 2 Select a standard gamma value. Notice how the picture of the curve changes when you select a gamma value. Click Recalibrate.
Adjustments Color - 32 Recalibrating Automatically Disables the Contrast and Brightness Buttons on the Front of Your Display Recalibrates If You Change Contrast or Brightness Recalibrates When You Change Screen Geometry or Screen Resolution Displays a Message Before Recalibrating Automatically 1 2 3 Click Preferences. Select your recalibration preferences. Important: If you select Time (recalibration every two weeks), your work can be interrupted without asking. Click OK.
Adjustments White Point Color - 33 Set Ambient Light Button Saving Color Settings You can save different combinations of white point, gamma curve value, and ambient light in named color settings. To save a color setting, 1 Gamma Curve Make sure white point, gamma curve, and ambient light are set as desired.
Adjustments Click to Save All Settings in the Color Window Color - 34 2 3 4 Optional: Click Recalibrate to see how the settings change the screen image. Click Save, and name the new color setting. Click Save, and the new name appears in the settings list.
Adjustments Color - 35 Using Existing Color Settings Settings List To use previously saved color settings, 1 2 Recalibrate Button Click a name in the settings list. Click Recalibrate.
Adjustments Setting to Delete Color - 36 Delete Button Deleting a Color Setting To delete a color setting, 1 2 Select the name of the setting you want to delete from the settings list. Click Delete.
Adjustments Color - 37 Overview of ColorSync Profiles The AppleVision display lets you create a ColorSync profile that describes the white point and gamma value for your display. Note: The ambient light setting is not saved as part of the ColorSync profile because ambient light changes as the physical location of the display changes. So the ambient light setting for one display will not be correct for another display.
Adjustments Color - 38 Sample Profile Name Save Button Exporting a ColorSync Profile To send a custom color setting to another display, 1 2 3 4 Export Button Make sure white point and gamma curve are set as desired. Click Recalibrate. Click Export. Enter a name for the profile, and click Save.
Adjustments Sample Profile Color - 39 Import Button Importing a ColorSync Profile To select a custom color setting from another display, 1 Click Import. 3 Click Recalibrate. 2 Select the profile you want and click Open. Important: To get truer color rendering, adjust for ambient light after importing a ColorSync profile.
Adjustments Introduction to the Sound Window (1710AV only) - 40 Introduction to the Sound Window (1710AV only) Before you make changes to the Sound window of AppleVision Setup, choose Control Panels from the Apple menu. Open the Sound control panel to select a sound input source, select a sound output device, and adjust volume. Refer to Chapter 5, “Using Sound and Video,” from the User’s Guide (a linked document) for more information.
Adjustments Sound (1710AV only) - 41 Sound (1710AV only) Sound Button 1 2 Press any control button to open the AppleVision Setup control panel. Click the Sound button.
Adjustments Click to Select Sound Input Source Sound (1710AV only) - 42 Selecting a Sound Input Source Note: Make sure you have selected a sound input port on the computer before selecting the sound input source for your display.
Adjustments Click to Select Sound Input Source Sound (1710AV only) - 43 • “Display’s Sound Input Port” if you want to use an audio device attached to the display’s input port
Adjustments Sound (1710AV only) - 44 Gain Slider 2 If you select “Display’s Sound Input Port,” drag the Sound Input Port Gain slider to set the desired gain. Note: Settings in the Sound window control sound only on the AppleVision 1710AV Display. To get desired results, you might also need to adjust sound on the computer connected to the display. Refer to the computer manual for more information.
Adjustments Sound (1710AV only) - 45 Selecting a Sound Output Device Refer to Chapter 5, “Using Sound and Video,” in the AppleVision 1710AV Display User’s Guide.
Adjustments Routing Button Sound (1710AV only) - 46 Routing Display Sound To select how the sound is routed, 1 Click Routing.
Adjustments Sound (1710AV only) - 47 2 Select a routing path. Click • “Loop Through Off” if you’re recording from a device and you don’t want to hear the sound on your display. • “Automatic” if you want sound routed to the speakers, headphones, and computer unless a voice-quality microphone is attached.
Adjustments Sound (1710AV only) - 48 3 Note: A voice-quality microphone is any microphone that has an extended stereo miniplug connector. Click OK.
Adjustments Sound (1710AV only) - 49 Adjusting Volume, Treble, and Bass 1 2 3 Speaker, Treble, and Base Slider Controls Headphone Slider Control Drag the Speaker Volume slider to adjust speaker volume. If desired, adjust treble and base by dragging their slider controls. If desired, adjust headphone volume by dragging the slider control to the right to increase volume or to the left to decrease volume.
Adjustments Sound (1710AV only) - 50 Note: When you make volume adjustments, “Mute all sound” is turned off automatically. When you make speaker volume adjustments and headphones are attached to the display, “ Mute speakers when headphones are attached” is turned off automatically.
Adjustments The Control Strip - 51 The Control Strip The control strip is a line of small icons that appears when you turn on the AppleVision display. The control strip allows you to make quick and easy changes to common settings such as screen resolution or color depth.
Adjustments The Control Strip - 52 Changing Screen Resolution To view or change the display’s screen resolution, 1 2 Move the pointer over the checkerboard screen icon, and hold down the mouse button. Select a screen resolution from the popup menu. Note: The example shows what you might see if two displays were connected to your computer.
Adjustments The Control Strip - 53 Changing Color Depth To view or change the display’s color depth, 1 2 Move the pointer over the striped screen icon, and hold down the mouse button. Select a color setting from the pop-up menu. Note: The example shows what you might see if two displays were connected to your computer.
Adjustments The Control Strip - 54 Scroll Arrow Close Box Tab Color Depth Screen Resolution To... Do this...
K Service Source Exploded View AppleVision 1710AV/1710 Display
Exploded View 1 922-1455 Front Bezel 922-1677 Microphone Cable 661-0914 CRT/Video Board 922-1511 On Screen Display Switches Board 922-2265 Plate, Blank Bezel (1710) 922-1502 Microphone Assembly (1710 AV) 922-1453 Rear Housing 922-1516 Rear Housing Screw Cover Plug 922-1602 Sound Enclosure Bezel 922-1597 Sound Control Board with Buttons 922-1600 Speaker (1 Only) 922-1679 9-Pin Cable 922-1509 Intermediate Board 661-0910 Main Deflection Board with Chassis 922-1599 Sound Board 922-1495 Sound Enclosure
