How to Guide

VOC: <20 g/L (regulatory)
HANDLING PRECAUTIONS: Store product in the cargo area of vehicle, and secure on top of 6
mill plastic sheeting to prevent damage due to accidental spills. Product safety information
required for safe use is not included. Before handling, read product safety data sheets and
container labels for safe use and for physical and health hazard information. Safety Data
Sheets are available on the APOC website at www.apoc.com, the APOC APP, by contacting
APOC at [e-mail] or calling [phone].
LIMITED WARRANTY AND DISCLAIMER: To the best of our knowledge, the technical data
contained herein is true and accurate at the date of issuance and is subject to change without
prior notice. User must contact APOC to verify correctness before specifying or ordering. No
guarantee of accuracy is given or implied. APOC Roong Systems, Inc. (herein “APOC”)
hereby warrants to the original purchaser, contingent upon original proof of purchase, that
this product will be free from any and all manufacturing defects that may materially and
adversely affect the product’s performance for a period of one (1) year from the date of
original purchase (“Warranty Period”). Product must be applied in accordance with the proper
application procedures, and for the intended use as stated on the label. Proper preparation
and drying conditions must be observed to achieve correct results. Should a manufacturing
defect materially and adversely affect this product’s performance, APOC shall, within its sole
discretion and upon receipt of Purchaser’s timely written notice within the Warranty Period,
provide replacement product(s) or refund the purchase price of the defective product. THIS
LIMITED WARRANTY IS PURCHASER’S SOLE AND EXCLUSIVE WARRANTY AND REPLACES
ALL OTHER WARRANTIES, CONDITIONS, REPRESENTATIONS AND GUARANTEES,
WHETHER EXPRESS OR IMPLIED, WHETHER BY STATUTE, AT LAW OR IN EQUITY,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. This limited warranty does not cover labor or installation costs, water
damage, consequential damages or incidental damages. Under no circumstances will APOC
be liable for any amount in excess of the product purchase price. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specic legal rights, and you may also have other rights which vary
from state to state. Direct all warranty claims in writing along with original proof of purchase
to APOC, c/o Warranty Claims Department, P.O. Box 5449, Tampa, FL 33675. The exclusive
venue for any legal action arising out of the purchase of this product or this warranty shall
be had in a court of competent jurisdiction within Hillsborough County, Florida. Florida law
shall govern. For additional Limited Warranty information, visit www.apoc.com/pages/warranty.
LIMITED EXTENDED WARRANTY ELIGIBILITY REQUIREMENTS: For information and eligibility
requirements for APOC Roof Systems, Corp. (“APOC”) LIMITED EXTENDED WARRANTIES,
visit www.apoc.com/pages/extendedwarranty. EXTENDED WARRANTIES vary by product and
application rates and are not available for all products.
Approx. Shipping Weights: (Note: All approx. weights include container)
10 . oz tube (296ml) 1lb.
1 Case (12 tubes) 12 lbs.
Product Colors
White AP-1000-1-61
Gray AP-1000-7-61
Gardner-Gibson, Inc. • P.O. Box 5449 • Tampa, Florida 33675-5449
Phone: [phone] • Fax [phone] • www.apoc.com
G-19
COMPLIANCE: Exceeds performance requirements of ASTM C920, Type S,
Grade Class NS
DESCRIPTION: APOC
®
AP-1 Green-Seal
®
Lifetime Heavy Duty Construction
Sealant & Adhesive is an all-purpose, paintable, structural adhesive
and sealant that can be used in a wide variety of industrial, commercial
and residential applications. AP-1 Green-Seal is a moisture cure, hybrid
technology that can be used for roong, solar, HVAC, siding, general
construction, landscaping, plumbing and many other applications. AP-1
Green-Seal bonds to most building materials including glass, wood, masonry,
block, asphalt shingles, tile, aged single plies, insulation, foam, aluminum,
metal and many other substrates. Not recommended on smooth surfaced
asphalt. It forms a highly exible, elastic and waterproof seal, exceeding
the rigorous demands of the professional contractor. It performs under the
toughest conditions, including extreme rain, desert heat, freeze thaw cycles
and sub-zero temperatures. Engineered with sustainability in mind, Green-
Seal is isocyanate free and low VOC. It provides a safer, stronger and superior
application with minimal impact on the environment. AP-1 Green-Seal is
specially designed and optimized for maximum performance, providing
peace of mind to contractors, building owners and homeowners alike. Green-
Seal is sustainable by design and engineered to outperform.
PREPARATION: For detailed application instructions, download the APOC
APP, or visit www.apoc.com. Completely read all application instructions
and check weather conditions prior to starting any work. If moisture or dew
is present, product will bond, however use only as a topical or temporary
repair to avoid water entrapment. All surfaces should have proper drainage,
be clean, dry and free from all dirt, grease, debris, rust, release agents or
other contamination that may prevent proper bonding or reduce the sealant’s
performance. Clean surfaces using appropriate cleaner for substrate.
Isopropyl alcohol or other approved cleaners may be used to clean and
prepare surface prior to application. Surface and air temperatures must be
above 32 °F (for 24 hours) and rising, but not above 110 °F.
FOR BEST RESULTS: Sealant should be stored at room temperature prior to
application. This will provide the opportunity for correct tooling and proper
adhesion for application in cold temperatures or where moisture may be
present. Once container is opened, use all product right away. Opened
product will immediately begin to cure from surrounding moisture in contact
with the sealant and / or from humidity in the air.
FALL PROTECTION WARNING: Always use personal fall protection devices
and follow procedures in accordance with OSHA and local regulatory
requirements when walking or working on roofs. Use safety equipment such
as tie-offs, safety lines, body harnesses, toe boards and ladders. Dusty, damp
or wet conditions as well as certain shoes can result in slippery surfaces
and create a fall hazard. Always be cognizant of where you are in relation
to your surroundings, including but not limited to: the edge of the roof, any
projections, skylights and any other objects which could cause you to slip or
fall. Falling from a roof can result in serious harm or death.
APPLICATION: Protective clothing, gloves and eyewear should be used during
application of these products. Apply with a caulking gun. Trim nozzle to
desired bead size, puncture foil seal at inner base inside the nozzle and
load into caulk gun. While applying sealant, hold nozzle at a 45° angle,
pushing sealant into gap. Sealant may be brushed or troweled to desired
nish. All joints should utilize a backer rod that is 25% larger than the joint
opening. Other approved bond breakers may also be used to ensure proper
movement of joint. All joints must be installed according to ASTM and SWRI
recommendations and guidelines. Design all joints with a depth to width ratio
of 1:2 (joint width should be 2X the joint depth). Can be coated or painted
and fully cures in 48 hours at 70 °F & 50% relative humidity. Low humidity,
thicker lms, poor air ow and lower temperatures will increase dry times.
DO NOT THIN.
LIMITATIONS: Avoid substrates/joints contaminated with grease, wax and
/ or corrosion. Long term exposure to corrosive chemicals may result in
deterioration of sealant. A compatibility test must be performed if used in
conjunction or close proximity with another sealant.
CLEAN-UP: Xylene, Toluene, or MEK
GREEN-SEAL
®
HEAVY DUTY CONSTRUCTION SEALANT & ADHESIVE
DATA SHEET
AP-1
©2019 Gardner-Gibson, Inc.
Manufactured by / Fabricado por:
Gardner-Gibson, Inc.
P.O. Box 5449, Tampa, FL 33675
See SDS for more info
TYPICAL PHYSICAL & PERFORMANCE CHARACTERISTICS:
Density 11.5 lbs./gal.
Low Temp Flex @ (-20 ˚C) Pass
Tack Free 30 min.
Solids by Weight >95%
Tensile Strength >200 psi
Elongation (ASTM D412) >150%
Slump @ 80 ˚C Pass
Consistency Pliable
Skin Time (50% Relative Humidity, 70 ˚F) 2-4 hours
Full Cure (50% Relative Humidity, 70 ˚F) 24 hours
Application Temperatures 40 ˚F-110 ˚F
Clean-up Tools Xylene, Toluene, MEK
Shore Hardness (A) 55 ± 5
Shelf Life (Store < 80 ˚F) (50% RH) 12 months
(original, unopened container)
Sag None
Water Resistance Pass
Clean-up Xylene, Toluene, or MEK