APC-3X92X Panel PC User Manual Release Date Revision Jan. 2013 Jun. 2013 ® 2013 Aplex Technology, Inc. V1.0 V1.1 All Rights Reserved. Published in Taiwan Aplex Technology, Inc. 15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan Tel: 886-2-82262881 Fax: 886-2-82262883 E-mail: aplex@aplex.com.tw APC-3X92X User Manual URL: www.aplex.com.
Warning!_______________________________ This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, it may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
Packing List Accessories (as ticked) included in this package are: □ AC power cable □ Driver & manual CD disc □ Other.___________________(please specify) Safety Precautions Follow the messages below to avoid your systems from damage: ◆ Avoid your system from static electricity on all occasions. ◆ Prevent electric shock. Don„t touch any components of this card when the card is power-on. Always disconnect power when the system is not in use. ◆ Disconnect power when you change any hardware devices.
Table of Contents______________________ Warning!…………………………………………………………………………….……..….2 Disclaimer………………………………………………………………….…………………2 Packing List...................................................................................................................3 Safety Precautions........................................................................................................3 Chapter 1 Getting Started 1.1 Specifications………………………………………….………….……...…..6 1.2 Dimensions…………………………………...……………….…………......
Chapter 5 Touch Screen Installation 5.1 Introduction to Touch Screen Controller Board………………………....64 5.2 Windows 2000/XP USB Driver Installation………………….………..….64 5.2.1 Installing software……………………………………………………...…64 5.2.2 Software Function(Projected Capacitive)………………………………70 5.2.3 Software Function(Resistive Touch)……………………………………76 Figures Figure 1.1: Dimensions of the APC-3592…..……………………………...8 Figure 1.2: Dimensions of APC-3592A…………….....……………………...9 Figure 1.3: Dimensions of APC-3792R..…………………...………………..
Chapter 1________________Getting Started 1.1 Specifications Model No. Specs APC-3592 APC-3592A APC-3792R APC-3792P System Processor Intel Atom Intel Atom Intel Atom Intel Atom Processor D525 Processor N455 Processor D525 Processor N455 1.8GHz built-in 1.66GHz built-in 1.8GHz built-in 1.66GHz built-in System Chipset Intel ICH8M Chipset System Memory 1 x 204 Pin DDR3 800MHz SO-DIMM socket, default 2GB Storage 1 x 2.5” SATA HDD 1 x Internal CF Slot External I/O Port 2 x USB 2.
Power Input 11~32V DC Mechanical Construction Stainless steel IP Rating IP65 Mounting VESA IP65/IP69K IP65 IP65/IP69K 100x100/200x100 VESA 75x75 Mount Mount Dimensions (WxHxD) 399x324x83 399x324x65 432x358x67.9 432x358x65 Net Weight 7.2kgs 7.1kgs 8.9kgs 8.
1.
Figure 1.
Figure 1.
Figure 1.
Figure 1.
1.3 Brief Description of the APC-3X92X APC-3X92X is a power-optimized and delivers robust performance-per-watt for embedded Panel PC. The powered by an Atom D525 1.8 GHz processor for APC-3592/3792R and an Atom N455 1.66GHz processor for APC-3592A/3792P. It comes with an internal compact flash slot, 2.5-inch hard disk drive, DDR3 memory, 1 Ethernet, DC input, and 2 USB ports. The unit supports Windows XP Professional, XP Embedded, Windows 7, Windows Embedded Standard 7.
Figure 1.8: Rear View of APC-3592 Figure 1.9: Rear View of APC-3792R Figure 1.
Chapter 2__________Hardware Installation 2.1 Mainboard Specifications Figure 2.1: Mainboard Overview Figure 2.
Figure 2.3: Jumpers and Connectors Location-TOP Figure 2.
Specifications Board Size 165mm x 115mm CPU Support Intel Atom D525 /1.80GHz (onboard) Intel Atom N455 /1.
Management Front I/O 1 x 2-pin power input connector by 2x5-pin header Power on/off switch Reset switch Power LED status HDD LED status Buzzer Watchdog Timer External I/O port Software programmable 1 – 255 second by Super I/O 1 x COM Port (COM1) 4 x USB 2.0 Ports (stack) 2 x RJ45 GbE Ports (10/100/1000Mbps) 1 x DB15 Port or 2x8 Pin Header Temperature Operating: -20℃–70℃ Storage: -40℃–85℃ Humidity 5% - 95%, non-condensing, operating Power Consumption 12V /1.
2.2 Jumpers Setting and Connectors 1. JCLR_CMOS: (2.0mm Pitch 1x3 Pin Header)CMOS clear jumper, CMOS clear operation will permanently reset old BIOS settings to factory defaults. JCLR_CMOS CMOS CLOSE 1-2 NORMAL (default) CLOSE 2-3 Clear CMOS Procedures of CMOS clear: 5.4.1.1 Turn off the system and unplug the power cord from the power outlet. 5.4.1.2 To clear the CMOS settings, use the jumper cap to close pins 2 and 3 for about 3 seconds then reinstall the jumper clip back to pins 1 and 2. 5.4.1.
Close 6. 7. Power Auto on (Default) BAT: (1.25mm Pitch 1x2 box Pin Header) 3.0V Li battery is embedded to provide power for CMOS. Pin# Signal Name Pin1 VBAT PIN2 Ground F_PANEL: (2.0mm Pitch 2X5 Pin Header), Front panel connector. Signal Name HD LED+ Pin# Pin# 1 2 Signal Name POWER LED+ HD LED- 3 4 POWER LED- Ground 5 6 PWRBTN RESET 7 8 Ground BUZZER+ 9 10 BUZZER- Pin1-3: HDD LED, They are used to connect hard disk activity LED.
8. USB3: (2.0mm Pitch 2x5 Pin Header) ,Front USB connector, it provides two USB ports via a dedicated USB cable, speed up to 480Mb/s. Signal Name Pin# Pin# Signal Name +5V 1 2 +5V USB_P6_DN 3 4 USB_P7_DN USB_P6_DP 5 6 USB_P7_DP Ground 7 8 Ground NC 9 10 Ground Note: Before connection, make sure that pinout of the USB Cable is in accordance with that of the said tables. Any inconformity may cause system down and even hardware damages. 9. JCOM: (2.
10. GPIO: (2.0mm Pitch 2x5 Pin Header),General-purpose input/output port, it provides a group of self-programming interfaces to customers for flexible use. Signal Name 11. Pin# Pin# Signal Name GPIO20 1 2 GPIO60 GPIO21 3 4 GPIO61 GPIO22 5 6 GPIO62 GPIO23 7 8 GPIO63 Ground 9 10 +5V COM33: (2.0mm Pitch 1x4 box Pin Header),it provides selectable RS422/RS485 serial signal output.
FRONT-MIC_L 13. 9 10 FRONT-MIC_ R COM2-COM6: (2.0mm Pitch 2x5 Pin Header),COM2 COM3 COM4 COM5 COM6 Ports, up to 5 standard RS232 ports are provided. They can be used directly via COM cable connection.
15. 3 Ground 4 +5V 5 KBCLK 6 MSCLK USB1/2: (Double stack USB type A), Rear USB connector, it provides up to 4 USB2.0 ports, speed up to 480Mb/s. Each USB Type A Receptacle (2 Ports) Current limited value is 1.5A. If the external USB device current exceeds 1.5A, please separate connectors into different Receptacle. 16. LAN1/2: (RJ45 Connector), Rear LAN port,2 standard 10/100/1000M RJ-45 Ethernet ports are provided.
C CRT_R_VSYN C 9 10 CRT_PU_DDC_CLK NC 11 12 NC +12V 13 14 Ground +12V 15 16 Ground 19. CPU SCREW HOLES: Four screw holes for fixed CPU Cooler assemble. 20. COM1: (Type DB9),Rear serial port, standard DB9 serial port is provided to make a direct connection to serial devices. COM1 port is controlled by pins No.1~6 of JCOM,select output Signal RI or 5V or 12v, For details, please refer to description of JCOM. 21. AT12V: (5.
23. 24. LVDS: For 18 bit LVDS output connector, Fully supported by Intel Atom D525 chipset, the interface features single channel 18-bit output. Model name of the interface connector is Hirose DF13-30DP-1.25V.
1 +DC5V 2 Ground 3 Ground 4 +DC12V Note: Output current of the connector must not be above 1A. 27. CN1: (2.5mm Pitch 1x2 box Pin Header),an onboard 5V output connector is reserved to provide power for IDE/SATA devices. Pin# Signal Name 1 +DC5V 2 Ground Note: Output current of the connector must not be above 1A. 28. PC104+: cation. (4x30 Pin), PC104 plus connector, it conforms to standard PC104+ specifi- 29.
Chapter 3 BIOS Setup 3.1 Operations after POST Screen After CMOS discharge or BIOS flashing operation, the system will display the following screen for your further operation. Press F2 key to continue or F1 key to enter CMOS Setup. AMIBIOS© 2009 American Mega trends , Inc. BIOS Date: 03/22/12 15:57:19 Ver: 08.00.16 CPU : Intel® Atom™ CPU D525 @ 1.80GHz Speed : 1.80 GHz Press F11 for BBS POPUP Initializing USB Controllers. . 2038MB OK Done. Auto-Detecting Pri Master..
Please select boot device： Hitachi HTS545016B9A300 USB: USB Hotplug FDD ↑and ↓ to move selection ENTER to select Boot device ESC to boot using defaults 3.2 BIOS SETUP UTILITY Press [Del] key to enter BIOS Setup utility during POST, and then a main menu containing system summary information will appear. BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit System Overview User [ENTER]，[TAB] AMIBIOS or Version [SHIFT-TAB] to Select a field : 08.00.
3.3 System Overview BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit System Overview User [ENTER]，[TAB] AMIBIOS or Version [SHIFT-TAB] to Select a field : 08.00.16 Build Date : 03/22/12 ID Use[+] or [-] to : L706V012 configure system Time. Processor Intel ® Atom™ CPU D525 Speed Count @ 1.
3.4 Advanced Settings BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Advanced Settings Exit Configure CPU WARNING: Setting wrong values In below sections may cause system to malfunction.
V02.68 © Copyright 1985-2009 American Mega trends , Inc. Max CPUID Value Limit: [Disabled] [Enabled] Execute Disable Bit Capability: [Enabled] [Disabled] Hyper Threading Technology: [Enabled] [Disabled] 3.4.
ATA/IDE Configuration: [Enhanced] [Disabled] Configure SATA as: [IDE] [RAID] [AHCI] Hard Disk Write Protect: [Disabled] [Enabled] IDE Detect Time Out : [35] Options: [0,5,10,15,20,25,30,35] ATA(PI) 80Pin Cable Detection: [Host & Device] [Host] [Device] 3.4.
Serial Port3 Type: COM3 Options: [RS232 Type] [RS485 Type] WatchDog Setting: [Disable] Options: [10sec,20sec,30sec,40sec,1min,2min,4min] 3.4.4 Hardware Health Configuration BIOS SETUP UTILITY Advanced Hardware Health Configuration Fan configuration mode CPU Temperature :41℃/105℉ setting CPUFAN Speed :4800 RPM CPUFAN Mode Setting Mode ] CPUFAN PWM Control [Manual [250 ] ← Select Screen ↑↓ Select Item +- Charge Field F1 General Help F10 ESC Save and Exit Exit V02.
3.4.5 ACPI Configuration Section for Advanced ACPI Configuration Options: [Advanced ACPI Configuration] [Chipset ACPI Configuration] 3.4.6 AHCI Configuration BIOS SETUP UTILITY Advanced AHCI Configuration While entering setup, ► AHCI Port0 : [Not Detected] BIOS auto detects the ► AHCI Port1 : [Not Detected] presence of IDE ► AHCI Port2 : [Not Detected] devices.
F1 F10 ESC General Help Save and Exit Exit V02.68 © Copyright 1985-2009 American Mega trends , Inc. Configure the Multi-Processor Table. MPS Revision: [1.4] [1.1] 3.4.
[Auto] [Disabled] [Enable] Maximum Read Request Size: [Auto] [128/256/512/1024/2048/4096 Bytes] Set Maximum Read Request Size of PCI Express Device or allow System BIOS select the value. Active State Power Management: [Disabled] [Enable] Extended Synch: [Auto] [Disabled] [Enable] 3.4.
[Disabled] 3.4.10 USB Configuration BIOS SETUP UTILITY Advanced USB Configuration Enables support for Module Version – 2.24.5-14.4 legacy USB.ATUO option disables legacy support if no USB USB Devices Enabled : None Legacy USB Support USB2.
USB Mass Storage Device Configuration: BIOS SETUP UTILITY Advanced USB Mass Storage Device Configuration USB Mass Storage Reset Delay Number of seconds [20 Sec] POST waits for the USB mass storage device Device #1 after start unit command USB Hotplug Emulation Type [Auto] ← Select Screen ↑↓ Select Item +- Charge Field F1 General Help F10 Save and Exit ESC Exit V02.68 © Copyright 1985-2009 American Mega trends , Inc. 3.
IRQ3 [Available] +- Charge Field F1 General Help IRQ4 F10 [Available] ESC Save and Exit Exit IRQ5 [Available] IRQ6 [Available] IRQ7 [Available] IRQ9 [Available] IRQ10 [Available] V02.68 © Copyright 1985-2009 American Mega trends , Inc.
PCI IDE BusMaster: [Disabled] [Enable] OffBoard PCI/ISA IDE Card: Some PCI IDE cards may require this to be set to the PCI slot number that is holding the card. Auto:Works for most PCI IDE Cards. [Auto] [PCI Slot1] [PCI Slot2] [PCI Slot3] [PCI Slot4] [PCI Slot5] [PCI Slot6] IRQ3/4/5/7/9/10/11/14/15: [Available] [Reserved] Available: Specified IRQ is available to be used by PCI/PnP devices. Reserved: Specified IRQ is reserved for use by legacy ISA devices.
← Select Screen ↑↓ Select Item +- Charge Field F1 General Help F10 ESC Save and Exit Exit V02.68 © Copyright 1985-2009 American Mega trends , Inc. Boot Setting Configuration： Quick Boot: [Enabled] [Disabled] Allows BIOS to skip certain tests while booting .This will decrease the time needed to boot the system. Quiet Boot: [Disabled] [Enabled] Disabled: Displays normal POST messages. Enabled: Displays OEM logo instead of POST messages. AddOn ROM Display Mode: Set display mode for Option ROM.
[Auto] [Enabled] [Disabled] Wait For „F1‟ If Error: Wait for F1 key to be pressed if error occurs. [Enabled] [Disabled] Hit „DEL‟Messgae Display : Displays “press” DEL to run Setup in POST. [Enabled] [Disabled] Interrupt 19 Capture: [Disabled] [Enabled] Enabled: Allows option ROMs to trap interrupt 19. Boot Device Priority: Specifies the Boot Device Priority sequence. 3.
ESC Exit V02.68 © Copyright 1985-2009 American Mega trends , Inc. Change Supervisor Password: Install or Change the password. Change User Password: Install or Change the password. Password Check: [Setup] [Always] Setup: Check password while invoking setup. Always: Check password while invoking setup a well as on each boot. Boot Sector Virus Protection: [Disabled] [Enabled] Enabled / Disabled Boot Sector Virus Protection. Type the password with up to 6 characters and then press Enter key.
3.8 Advanced Chipset Settings BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Advanced Chipset Settings Exit Configure North Bridge WARNING: Setting wrong values in below sections may cause system to malfunction feature ► North Bridge Configuration ► South Bridge Configuration ← Select Screen ↑↓ Select Item Enter Go to sub screen F1 General Help F10 Save and Exit ESC Exit V02.68 © Copyright 1985-2009 American Mega trends , Inc.
F10 ► Video Function Configuration Save and Exit ESC Exit V02.68 © Copyright 1985-2009 American Mega trends , Inc. DRAM Frequency: [Auto] [Max MHz] Configure DRAM Timing By SPD: [Enabled] [Disabled] Initate Graphic Adapter: Select which graphics controller to use as the primary boot device.
Flat [1024x768LVDS] Panel Panel Backlight Control HDCP Support Type [Level 9] Disabled] ↑↓ Select Item +- Charge option F1 General Help F10 ESC Save and Exit Exit V02.68 © Copyright 1985-2009 American Mega trends , Inc.
3.8.2 South Bridge Configuration: BIOS SETUP UTILITY Chipset South Bridge Chipset Configuration USB Functions Ports] USB2.0 Controller Options [8 USB Disabled 2 USB Ports [Enabled] 82574LAN1 [Disabled] BOOT 82574LAN2 [Disabled] BOOT 4 USB Ports 6 USB Ports 8 USB Ports ← Select Screen LAN Wakeup [Disabled] ↑↓ Select Item HDA Controller [Disabled] +- Charge Field SMBUS Controller [Enabled] F1 General Help F10 SLP_S4# Min.
[Disabled] [Enabled] LAN WakeUp: [Disabled] [Enabled] HDA Controller: [Enabled] [Disabled] SMBUS Controller: [Enabled] [Disabled] SLP_S4# Min. Assertion Width: [1 to 2 Seconds] [4 to 5 Seconds] [3 to 4 Seconds] [2 to 3 Seconds] Restore on AC Power Loss: [Turn On] [Power Off] [Last Status] Power Button Delay 4s Func： [Disabled] [Enabled] 3.
← Select Screen ↑↓ Select Item Enter Go to sub screen F1 General Help F10 Save and Exit ESC Exit V02.68 © Copyright 1985-2009 American Mega trends , Inc.
Chapter 4 Installation of Drivers This chapter describes the installation procedures for software and drivers under the windows XP. The software and drivers are included with the motherboard. The contents include Intel chipset driver, VGA driver, LAN driver, Audio driver, Touch Panel driver. Installation instructions are given below.
4.1 Intel Chipset Driver To install the Intel chipset driver, please follow the steps below. Step 1. Select Intel (R) Chipset Atom D525/N455 + ICH8M from the list Step 2. Click Next to setup program.
Step 3. Read the license agreement. Click Yes to accept the terms of the license agreement. Step 4. Click Next to continue.
Step 5. Click Next. Step 6. Select Yes, I want to restart this computer now. media from the drives.
4.2 Intel GMA 3150 VGA Chipset Driver To install the VGA drivers, follow the steps below to proceed with the installation. Step 1. Select Intel GMA 3150 VGA Chipset. Step 2. Click Next to continue.
Step 3. Click Next to continue setup program. Step 4. Read the license agreement. APC-3X92X User Manual Click Yes to accept the license agreement.
Step 5. Click Next. Step 6. Click Next to continue.
Step 7. Select Yes, I want to restart this computer now. media from the drives.
4.3 Intel 82574L Network adapter Driver To install the Intel 82574L Network adapter Driver, please follow the steps below. Step 1. Select Intel(R) 82574L Network Adapter. Step 2. Click Next to continue.
Step 3. Read the license agreement. Select I accept the terms in the license agreement then click Next to continue. Step 4. Select Drivers, Intel(R) PROSet for Windows* Device Manager, Advanced Network Services. Click Next to continue.
Step 5. Click Install to begin the installation. Step 6. Click Finish to compete the installation.
4.4 Realtek HD Audio Driver Installation To install the Realtek High Definition (HD) Audio driver, please follow the steps below. Step 1. Select Realtek ALC662 HD Audio Driver from the list. Step 2. Wait for extracting the files then click Next to continue.
Step 3. Click Yes to continue the installation. Step 4. Wait for installation.
Step 5. Select Yes, I want to restart my computer now. then click OK.
Chapter 5 Touch Screen Installation This chapter describes how to install drivers and other software that will allow your Touch Screen Controller Board to work with different operating systems. 5.1 Introduction to Touch Screen Controller Board 15” projected capacitive touch panel control board is a touch screen control board designed for USB interface and specific for touch screens. It is designed with USB interface features with multiple devices supporting function.
Insert the Aplex product CD install setup.exe. the screen below would appear. Click touch panel driver. Step 3. Click Next to continue.
Step 4. Tick Install RS232 interface driver. Step 5. Select None. Then click Next to continue.
Step 6. Please make sure your touch monitor or touch controller‟s USB cable is plugged into the computer now. Click OK to continue the installation. Step 7. If you want to use Multi-Monitor, check Support Multi-Monitor System. continue the installation. Then, click Next to Step 8. Click Browse to create a new folder. Click Next to setup eGalaxTouch in the destination folder you want to install. Click Next to continue the installation.
Step 9. Under eGalaxTouch, select Accessories. Step 10. Check Create a eGalaxTouch Utility shortcut on desktop. APC-3X92X User Manual Click Next to continue.
Step 11. The installation files are extracted. Step 12. eGalaxTouch driver has been installed. To do 4 point calibration, click Yes to continue.
5.2.2 Software Functions(Projected Capacitive) Upon rebooting, the computer automatically finds the eGalax controller board. The touch screen is connected but not calibrated. Follow the procedures below to carry out calibration. General In this window, you can see there is USB Controller. Click OK to continue.
Setting Click OK to continue settings.
Tools Click OK to continue the settings. 4 Points Calibration Do 4 points alignment to match display. Clear and Calibrate Clear linearization parameter and do 4 points alignment. Linearization Do 9 points linearization for better touchscreen linearity. Draw Test Do draw test to verify the touch accuracy.
Display In this window, it shows the mode of display. Enable Multiple Monitors.
Hardware Click OK to continue. About To display information about eGalaxTouch and its version.
5.2.3 Software Functions (Resistive Touch) Upon rebooting, the computer automatically finds the new 6000 controller board. The touch screen is connected but not calibrated. Follow the procedures below to carry out calibration. 1. After installation, click the PenMount Monitor icon “PM” in the menu bar. 2. When the PenMount Control Panel appears, select a device to “Calibrate.
skip, press „ESC‟. Advanced Calibration Advanced Calibration uses 4, 9, 16 or 25 points to effectively calibrate touch panel linearity of aged touch screens. Click this button and touch the red squares in sequence with a stylus. To skip, press ESC‟. Command Calibration Command call calibration function. Use command mode call calibration function, this can uses Standard, 4, 9, 16 or 25 points to calibrate E.g. Please run ms-dos prompt or command prompt c:\Program Files\PenMount Universa Driver\Dmcctrl.
Step 2.Click “Standard Calibration” to start calibration procedure NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an accurate calibration. Use a stylus during Advanced Calibration for greater accuracy.
Step 3.Come back to “PenMount Control Panel” and select Tools then click Advanced Calibration. Step 4. Select Device to calibrate, then you can start to do Advanced Calibration. NOTE: Recommend to use a stylus during Advanced Calibration for greater accuracy.
Setting APC-3X92X User Manual 80
About This panel displays information about the PenMount controller and driver version.
Multiple Monitors Multiple Monitors support from two to six touch screen displays for one system. The PenMount drivers for Windows 2000/XP support Multiple Monitors. This function supports from two to six touch screen displays for one system. Each monitor requires its own PenMount touch screen control board, either installed inside the display or in a central unit. The PenMount control boards must be connected to the computer COM ports via the RS-232 interface.
2. When the mapping screen message appears, click OK. 3. Touch each screen as it displays “Please touch this monitor”. Following this sequence and touching each screen is called mapping the touch screens. 4. Touching all screens completes the mapping and the desktop reappears on the monitors. 5. Select a display and execute the “Calibration” function. A message to start calibration appears. Click OK.
6. “Touch this screen to start its calibration” appears on one of the screens. Touch the screen. 7. “Touch the red square” messages appear. Touch the red squares in sequence. 8. Continue calibration for each monitor by clicking Standard Calibration and touching the red squares. NOTES: 1. If you use a single VGA output for multiple monitors, please do not use the Multiple Monitor function. Just follow the regular procedure for calibration on each of your desktop monitors. 2.
PenMount Monitor has the following function PenMount Rotating Functions The PenMount driver for Windows 2000/XP supports several display rotating software packages. Windows Me/2000/XP support display rotating software packages such as: • Portrait‟s Pivot Screen Rotation Software • ATI Display Driver Rotate Function • nVidia Display Driver Rotate Function • SMI Display Driver Rotate Function • Intel 845G/GE Display Driver Rotate Function Configuring the Rotate Function 1.
