APC-3X65 User Manual Release Date Revision Jun 2013 ® 2013 Aplex Technology, Inc. V1.0 All Rights Reserved. Published in Taiwan Aplex Technology, Inc. 15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan Tel: 886-2-82262881 Fax: 886-2-82262883 E-mail: aplex@aplex.com.tw APC-3X65 User Manual URL: www.aplex.com.
Warning!_______________________________ This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, it may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
Packing List Accessories (as ticked) included in this package are: □ AC power cable □ Driver & manual CD disc □ Other.___________________(please specify) Safety Precautions Follow the messages below to avoid your systems from damage: ◆ Avoid your system from static electricity on all occasions. ◆ Prevent electric shock. Don‘t touch any components of this card when the card is power-on. Always disconnect power when the system is not in use. ◆ Disconnect power when you change any hardware devices.
Table of Contents______________________ Warning!…………………………………………………………………………….……..….2 Disclaimer………………………………………………………………….…………………2 Packing List...................................................................................................................3 Safety Precautions........................................................................................................3 Chapter 1 Getting Started 1.1 Specifications………………………………………….………….……...…..6 1.2 Dimensions…………………………………...……………….…………......
4.1 Intel Chipset Driver.…………………………...……………………………53 4.2 Intel (R) VGA Chipset Driver..…................…......……………….......…..56 4.3 Intel(R) Network adapter Driver…........…..................................……….59 4.4 Realtek HD Audio Driver Installation………………….…………………62 Chapter 5 Touch Screen Installation 5.1 Introduction to Touch Screen Controller Board………………………....64 5.2 Windows 2000/XP USB Driver Installation………………….………..….64 Figures Figure 1.1: Dimensions of APC-3265………...……………………………...8 Figure 1.
Chapter 1________________Getting Started 1.1 Specifications Model No. APC-3265 Specs APC-3565 APC-3765 System Processor Intel Atom D2550 1.8GHz System Chipset Intel NM 10 Express Chipset System Memory 2 x 204-pin DDR3 SO-DIMM 800/1066MHz Up to 4G (D2550) Storage 1 x 2.5” SATA HDD Space 1 x External CF slot, 1 x Slim CD/DVD RW device for option(Not available if CF have been used) External I/O Port USB 4 x USB 2.
Touch Screen Type Resistive Touch Interface Default USB Optional RS-232 Light Transmission 80% Power Supply Power Input DC 9~32V Mechanical Construction 413C steel front bezel, 413C steel back cover IP Rating Front bezel IP65 Mounting Panel mount Dimensions (WxHxD) (mm) Net weight(kgs) 390x264x122.5 409 x 309 x123 457x355x129.4 6.4 7.4 7.
1.2 Dimensions Figure 1.
Figure 1.
Figure 1.
1.3 Brief Description of APC-3X65 The APC-3x65 is the fanless and low power consumption panel-mount industrial panel PC with 12.1”/15”/17” TFT LCD. It powered by Intel Atom D2550 1.8GHz. The panel PC has a rich variety of functions and peripherals. It comes with 1 x 2.
Figure 1.
Chapter 2__________Hardware Installation 2.1 Mainboard Specifications Introduction ASB-M7101 is a Mini-ITX industrial motherboard developed on the basis of Intel D2550 and NM10, which provides abundant peripheral interfaces to meet the needs of different customers. Also, it features dual 1000M LAN port, 6-COM port and one Mini PCIE configuration. To satisfy the special needs of high-end customers, PC104+ socket (capable of adjusting IO voltage) richer extension functions.
Dual Display CRT+LVDS1 CRT+LVDS2 CRT+HDMI LVDS1+HDMI LVDS2+HDMI Super I/O Winbond W83627UHG BIOS AMIBIOS Storage 2 x SATA Connector 1 x Compact Flash II Slot for TB-522 or TB-523 (option） Ethernet 2 x PCIe Gbe LAN by Intel 82583V 4 x USB 2.0 stack ports for external USB 3 x USB 2.0 box Pin header for MIO1 1 x USB 2.
Management DC12V output by 2x2 pin Connectors Switches and Power on/off switch by TB-522 or TB-523 LED Indicators Reset switch by MIO2 Power LED status by MIO2 HDD LED status by MIO2 External I/O port 2 x COM Ports (COM1/COM2) 4 x USB 2.
2.2 Board Dimensions Figure 2.
2.3 Jumpers and Connectors Location Board Top Figure 2.
Board Bottom Figure 2.
2.4 Jumpers Setting and Connectors 1. JP1: (2.0mm Pitch 1X3 Pin Header)CMOS clear jumper, CMOS clear operation will permanently reset old BIOS settings to factory defaults. JP1 CMOS Close 1-2 NORMAL (Default) Close 2-3 Clear CMOS Procedures of CMOS clear: a) Turn off the system and unplug the power cord from the power outlet. b) To clear the CMOS settings, use the jumper cap to close pins2 and 3 for about 3 seconds then reinstall the jumper clip back to pins open. c) Power on the system again.
5. DCIN: (5.08mm Pitch 1x3 Pin Connector),DC9V ~ DC32V System power input connector。 Power Mode Pin# Power Input Pin1 DC+9V~32V Pin2 Ground Pin3 PG Location : DCIN Location: ATX12V Location: ATX1 (5.4.5.) (5.4.6.) (5.4.7.) DC INPUT input output NC (Default) DC9~32V DC 12V ATX Power (option) 6. NC Input (DC12V) PSON,GND,5VSB ATX Power 2*2P ATX Power ATX12V: (2x2 Pin Connector),DC12V System power output connector. 7.
8. U2: (FCBGA559), onboard CPU . MODEL 9. CPU ASB-M7101T-D2550 Intel Atom D2550 1.86GHz ASB-M7101B-D2550 (option) Intel Atom D2550 1.86GHz ASB-M7101T-N2800 (option) Intel Atom N2800 1.86GHz ASB-M7101B-N2800 (option) Intel Atom N2800 1.86GHz ASB-M7101T-N2600 (option) Intel Atom N2600 1.60GHz ASB-M7101B-N2600 (option) Intel Atom N2600 1.60GHz CPU_FAN/SYS_FAN: (2.54mm Pitch 1x3 Pin wafer connector),Fan connector, cooling fans can be connected directly for use.
12. VGA_PH(option): (CRT 2.0mm Pitch 2X6 Pin Header), Video Graphic Array Port, Provide 2x5Pin cable to VGA Port, they can not work at the same time for VGA and VGA_PH.
14. LVDS1: (1.25mm Pitch 2x20 Connector, DF13A-40DP-1.25V),For 18/24-bit LVDS1 output connector, Fully supported by U2 Intel Processor, the interface features single channel 18/24-bit output. Low Voltage Differential Signaling, A high speed, low power data transmission standard used for display connections to LCD panels.
Pin# Signal Name 1 +DC12V 2 +DC12V 3 Ground 4 Ground 5 BKLT_EN 6 BKLT_CTRL Note: Pin6 is backlight control signal, support DC or PWM mode, mode select at BIOS CMOS menu. 17. LVDS2(option): (1.25mm Pitch 2x20 Connector, DF13A-40DP-1.25V), For 18/24-bit LVDS2 output connector, Fully supported by Parad PS8625(DP to LVDS), the interface features dual channel 24-bit output.
18. HDMI: (HDMI 19P Connector), High Definition Multimedia Interface connector. 19. BTN: POWER on/off Button, They are used to connect power switch button. The two pins are disconnected under normal condition. You may short them temporarily to realize system startup & shutdown or awaken the system from sleep state. 20. JP2: (2.0mm Pitch 2x3 Pin Header),COM1 jumper setting, pin 1~6 are used to select signal out of pin 9 of COM1 port. JP2 Pin# 21.
COM1/RS232 (Default): Pin# Signal Name 1 DCD# (Data Carrier Detect) 2 RXD (Received Data) 3 TXD (Transmit Data) 4 DTR (Data Terminal Ready) 5 Ground 6 DSR (Data Set Ready) 7 RTS (Request To Send) 8 CTS (Clear To Send) 9 RI/5V/12V (JP2 select Setting) COM1/RS422 (option): Pin# Signal Name 1 422_RX+ 2 422_RX- 3 422_TX- 4 422_TX+ 5 Ground 6 NC 7 NC 8 NC 9 5V/12V (JP2 select Setting) COM1/RS485 (option): Pin# Signal Name 1 NC 2 NC 3 485- 4 485+ 5 Ground 6 N
23. JP3: (2.0mm Pitch 2x3 Pin Header),COM2 jumper setting, pin 1~6 are used to select signal out of pin 9 of COM2 port. JP3 Pin# 24. Function Close 1-2 COM2 RI (Ring Indicator) (default) Close 3-4 COM2 Pin9=+5V (option) Close 5-6 COM2 Pin9=+12V (option) COM2: (Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a direct connection to serial devices. Pin# 25.
26. JP4: (2.0mm Pitch 2x3 Pin Header) COM6 setting jumper, pin 1~6 are used to select signal out of pin 9 of COM6 port. JP4 Pin# 27. Function Close 1-2 COM6 RI (Ring Indicator) (default) Close 3-4 COM6 Pin9=+5V (option) Close 5-6 COM6 Pin9=+12V (option) COM6: (2.0mm Pitch 2X5 Pin Header), COM6 Port, standard RS232 ports are provided. They can be used directly via COM cable connection. COM6 port is controlled by pins No.
. LAN1/LAN2: (RJ45 Connector), Rear LAN port, Two standard 10/100/1000M RJ-45 Ethernet ports are provided. Used Intel 82583V chipset, LINK LED (green) and ACTIVE LED (yellow) respectively located at the left-hand and right-hand side of the Ethernet port indicate the activity and transmission state of LAN. 30. JACK: (Diameter 3.5mm Double stack Jack), HD Audio port, An onboard Realtek ALC662 codec is used to provide high quality audio I/O ports.
33. JP_104P: (2.0mm Pitch 1X3 Pin Header) PC104+ port voltage selection jumper, select voltage for PCI-104 Plus devices. The default for this jumper is “all open”,meaning the user must select the voltage to be used. 34. JP_104P Pin# PC104+ VIO Voltage All Open Default Close 1-2 +3.3V PCI Card Close 2-3 +5V PCI Card PC104+ (option): (4x30 Pin), PC104 plus connector, it conforms to standard PC104+ specification. Can expand support four PCI devices. 35.
37. LED1: LED1：Power LED Status. 38. LED2: LED2：LED Status. Green LED for Motherboard Standby Power Good status, Yellow LED for HDD status. 39. MIO1: (DF13-40P Connector),For expand output connector, It provides two RS232 ports or one RS485 port, three USB ports, one power led, one power button, via a dedicated cable connected to TB-522 MIO1or TB-523 MIO1.
40. MIO2: (DF13-40P Connector),Front panel connector.
Pin11~Pin18: GPIO IN/GPIO OUT, General-purpose input/output port, it provides a group of self-programming interfaces to customers for flexible use. Pin19~Pin24: PS2 KB/MS, PS/2 keyboard and mouse port, the port can be connected to PS/2 keyboard and mouse via a dedicated cable for direct used. Note: When connecting LEDs and buzzer and GPIO and USB, pay special attention to the signal polarity.
46. H5/H6: MPCIE1 SCREW HOLES, H5 for mini PCIE card (30mmx30mm) assemble. H6 for mini PCIE card (30mmx50.95mm) assemble. 49. TB-520P2: TB-520P2 connect to ASB-M7101T PC104+ connector, PC104+ is located at the top, It provides two PCI slots. 50. TB-520P1E1: TB-520P1E1 connect to ASB-M7101T PC104+ and PCIE1X connector,PC104+ and PCIE1X are located at the top, It provides one PCI slot and one PCIE slot.
Chapter 3 3.1 BIOS Setup Operations after POST Screen After CMOS discharge or BIOS flashing operation,.Press [Delete] key to enter CMOS Setup. Version 2.15.1226. Copyright (C) 2012 American Megatrends, Inc. BIOS Date: 05/14/2013 22:29:02 Ver: M7101V006 Press 〈DEL〉or〈ESC〉to enter setup A3 After optimizing and exiting CMOS Setup, the POST screen displayed for the first time is as follows and includes basic information on BIOS, CPU, memory, and storage devices.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security BIOS Information Save & Exit Intel Reference Code BIOS Vendor American Megatrends Core Version 4.6.5.3 Compliancy UEFI 2.3; PI 1.2 Project Version 7101V006 Version ►Intel RC Version System Language →←: Select Screen [English] ↑↓ : Select Item System Date [Sun 01/01/2012] Enter: System Time [00:00:09] +/- : Charge Opt.
System Language →←: Select Screen [English] ↑↓ : Select Item System Date [Sun 01/01/2012] Enter: Select System Time [00:00:09] +/- : Charge Opt. F1 : General Help Access Level Administrator F2: Previous Values F3:Optimized Defaults F4:Save and Exit ESC Exit Version 2.15.1226. Copyright (C) 2012 American Megatrends , Inc.
►W83627UHG HW Monitor →←: Select Screen ►Serial Port Console Redirection ↑↓ ►PPM Configuration Enter: : Select Item Select +/- : Charge Opt. F1 : General Help F2: Previous Values F3:Optimized Defaults F4:Save and Exit ESC Exit Version 2.15.1226. Copyright (C) 2012 American Megatrends , Inc. 3.4.1 PCI Subsystem Settings PCI Bus Driver Versio V2.05.
Enable Hibernation: [Enabled] [Disabled] ACPI Sleep State: [Both S1 and S3 available for OS to choose from] [Suspend Disabled] [S1 only (CPU Stop Clock）] [S3 only (Suspend to RAM) ] Lock Legacy Resources: [Disabled] [Enabled] S3 Video Repost: [Disabled] [Enabled] 3.4.
Limit CPUID Maximum: [Disabled] [Enabled] 3.4.4 Thermal Configuration CPU Thermal Configuration DTS SMM [Disabled] [Enabled] Platform Thermal Configuration Critical Trip Point [15C] Active Trip Point Lo [55 C] 3.4.
USB hardware delays a USB transfer time-out: [20 sec] [10 sec] [5 sec] [1 sec] Device reset time-out: [20 sec] [10 sec] [30 sec] [40 sec] Device power-up delay [Auto] [Manual] 3.4.7 W83627UHG Super IO Ch Configuration W83627UHG Super IO ch W83627UHG Serial Port 1 Configuration Serial Port 2 Configuration Serial Port 3 Configuration Serial Port 4 Configuration Serial Port 5 Configuration Serial Port 6 Configuration 3.4.8 W83627UHG HW Monitor PC Health Status Smart Fan Mode Configuration 3.4.
COM0 Console Redirection [Enabled] [Disabled] Console Redirection Settings Serial Port for Out-of-Band Management/ Windows Emergency Management Services (EMS) Console Redirection [Disabled] [Enabled] Console Redirection Settings 3.4.
3.5 Chipset Settings Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Host Bridge Parameters ►Host Bridge ►South Bridge →←: Select Screen ↑↓ : Select Item Enter: Select +/- : Charge Opt. F1 : General Help F2: Previous Values F3:Optimized Defaults F4:Save and Exit ESC Exit Version 2.15.1226. Copyright (C) 2012 American Megatrends , Inc. 3.5.
[1.25GB] [1.5GB] [1.75GB] [2GB] [2.25GB] [2.5GB] [2.75GB] [3GB] [3.
Fixed Graphics Memory [128MB] [256MB] ALS Support [Disabled] [Enabled] Back light Control [DC] [PWM] Backlight Logic [Positive] [Negative] Backlight Control Lev [Level 8] [Level 0] [Level 1] [Level 2] [Level 3] [Level 4] [Level 5] [Level 6] [Level 7] [Level 9] [Level 10] [Level 11] [Level 12] [Level 13] [Level 14] [Level 15] LVDS1 Setting: IGFX – Boot Type: [LVDS1] or [CRT+LVDS] Active LFP: [LVDS] LVDS2 Setting: 3.5.
PCI Express Root Port 0 PCI Express Root Port 1 PCI Express Root Port 2 PCI Express Root Port 3 DMI Link ASPM Control [Enabled] [Disabled] PCI-Exp. High Priorit [Disabled] [Enabled] High Precision Event Timer Configuration High Precision Timer [Enabled] [Disabled] SLP_S4 Assertion Widt [1-2 Seconds] [2-3 Seconds] [3-4 Seconds] [4-5 Seconds] 3.6 Boot Settings Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
→←: Select Screen Driver Option Priorities ↑↓ Boot Option Priorities Enter: : Select Item Select Boot Option #1 [SATA PM: Hitachi…] +/- : Charge Opt. Boot Option #2 […] F1 : General Help Hard Drive BBS Priorities F2: Previous Values F3:Optimized Defaults ►CSM Parameters F4:Save and Exit ESC Exit Version 2.15.1226. Copyright (C) 2012 American Megatrends , Inc.
Hard Drive BBS Priorities [SATA PM:*** … ] Boot Option #1 SATA PM:***… ****** Disabled CSM Parameters Launch CSM [Always] [Never] Boot option filter [UEFI and Legacy] [Legacy only] [UEFI only] Launch PXE OpROM poli [Legacy only] [Do not Launch] [UEFI only] Launch Storage OpROM [Legacy only] [Do not Launch] [UEFI only] Launch Video OpROM po [Do not Launch] [UEFI only] [Legacy only] Other PCI device ROM [UEFI OpROM] [Legacy OpROM] APC-3X65 User Manual 48
3.7 Security Settings Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Password Description Save & Exit Set Administrator Password If ONLY the Administrator’s password is set, Then this only limits access to Setup and is Only asked for when entering Setup. If ONLY the User’s password is set, then this Is a power on password and must be entered to Is a power on password and must be entered to Boot or enter Setup.
BIOS setup. This will prevent unauthorized persons from changing your system configurations. Also, the feature is capable of requesting users to enter the password prior to system boot to control unauthorized access to your computer. Users may enable the feature in Security Option of Advanced BIOS Features.
Save & reset Save Configuration and reset? [Yes] [No] Discard Changes and Reset Reset Without Saving Reset without saving? [Yes] [No] Save Changes Save Setup Values Save configuration? [Yes] [No] Discard Changes Load Previous Values Load Previous Values? [Yes] [No] Restore Defaults Load Optimized Defaults Load optimized Defaults? [Yes] [No] Save user Defaults Save Values as User Defaults Save configuration? [Yes] [No] Restore user Defaults Restore User Defaults Restore User Defaults? [Yes] [No] Launch EFI S
Chapter 4 Installation of Drivers This chapter describes the installation procedures for software and drivers under the windows XP. The software and drivers are included with the motherboard. The contents include Intel (R) Chipset NM10 Express, Intel (R) VGA Chipset, Intel 82583V Driver, Realtek ALC662 HD Audio Driver, Touch Panel Driver. Installation instructions are given below.
4.1 Intel Chipset Driver To install the Intel chipset driver, please follow the steps below. Step 1. Access Industrial Panel PC. Select Intel(R) Chipset NM10 Express. Step 2. Click Next to setup program.
Step 3. Read the license agreement. Click Yes to accept the terms of the license agreement. Step 4. Click Next to continue.
Step 5. Click Next. Step 6. Select Yes, I want to restart this computer now. media from the drives.
4.2 Intel (R) VGA Chipset Driver To install the VGA drivers, follow the steps below to proceed with the installation. Step 1. Select Intel(R) VGA Chipset Driver. Step 2. Tick Automatically run WinSAT and enable the Windows Aero desktop theme (if supported.) Click Next to continue.
Step 3. Read license agreement. Click Yes to continue. Step 4. Click Next.
Step 5. Click Next. Step 6. Select Yes, I want to restart this computer now. APC-3X65 User Manual Click Finish.
4.3 Intel(R) Network Adapter Driver To install the Intel 82574L Network adapter Driver, please follow the steps below. Step 1. Select Intel 82583V Driver. Step 1. Click Next to continue.
Step 2. Select I accept the terms in the license agreement. Click Next. Step 3. Select Drivers/Intel(R) PROSet for Windows* Device Manager/Advanced Network Services. Click Next to continue.
Step 4. Click Install to begin the installation. Step 5. Click Finish to compete the installation.
4.4 Realtek HD Audio Driver Installation To install the Realtek High Definition (HD) Audio driver, please follow the steps below. Step 1. Select Realtek ALC662 HD Audio Codec Driver from the list. Step 2. Wait for extracting the files then click Next to continue.
Step 3. Select Yes, I want to restart my computer now. then click Finish.
Chapter 5 Touch Screen Installation This chapter describes how to install drivers and other software that will allow your PenMount 6000 Controller Board to work with different operating systems. NOTE: PenMount USB drivers support up to 15 USB controllers. 5.1 Introduction to Touch Screen Controller Board PenMount 6300 USB control board is a touch screen control board designed for USB interface and specific for 4, 5, 8-wire touch screens.
Step 1. Please make sure your PenMount 6000 device had plugged in advance. If your device uses RS232 interface, please plugged in before the machine is turned on. When the system first detects the controller board, a screen appears that shows “Unknown Device”. Do not use this hardware wizard. Press Cancel. Step 2. Insert the Aplex product CD install setup.exe. the screen below would appear. Se touch panel driver Step 3. Click Next to continue.
Step 4. Read the license Agreement. Click I agree to agree the license agreement. Step 5. Choose the folder in which to install PenMount Windows Universal Driver. Click Install to start the installation.
Step 6. Wait for installation. Then click Next to continue. Step 7. Click Continue Anyway.
Step 8. Click Finish to compete installation.
5.2.2 Software Functions Upon rebooting, the computer automatically finds the new 6000 controller board. The touch screen is connected but not calibrated. Follow the procedures below to carry out calibration. 1. After installation, click the PenMount Monitor icon “PM” in the menu bar. 2. When the PenMount Control Panel appears, select a device to “Calibrate.
Advanced Calibration Advanced Calibration uses 4, 9, 16 or 25 points to effectively calibrate touch panel linearity of aged touch screens. Click this button and touch the red squares in sequence with a stylus. To skip, press ESC’. Command Calibration Command call calibration function. Use command mode call calibration function, this can uses Standard, 4, 9, 16 or 25 points to calibrate E.g. Please run ms-dos prompt or command prompt c:\Program Files\PenMount Universa Driver\Dmcctrl.
Step 2. Click Standard Calibration to start calibration procedure NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an accurate calibration. Use a stylus during Advanced Calibration for greater accuracy.
Step 3. Come back to PenMount Control Panel and select Tools then Click Advanced Calibration. Step 4. Select Device to calibrate, then you can start to do “Advanced Calibration”. NOTE: Recommend to use a stylus during Advanced Calibration for greater accuracy.
Setting APC-3X65 User Manual 73
About This panel displays information about the PenMount controller and driver version.
Multiple Monitors Multiple Monitors supports two to six touchscreen displays for one system. PenMount drivers for Windows 2000, XP 32/64bit, and 2003 support Multiple Monitors. This function supports from two to six touchscreen displays for one system. Each monitor requires its own PenMount touchscreen control board, either installed inside the displayor in a central unit. The PenMount control boards must be connected to the computer COM ports via the RS-232 interface.
Step 2. When the mapping screen message appears, click OK.
Step 3. Touch each screen as it displays Please touch this monitor. Press ‘S’ to skip Following this sequence and touching each screen is called mapping the touch screens. Step 4. After the setting procedure is finished, maybe you need to calibrate for each panel and controller. NOTES: 1. If you used a single VGA output for multiple monitors, please do not use the Multiple Monitors function. Just follow the regular procedure for calibration on each of your desktop monitors. 2.
About You can see how many devices of PenMount controller that are plugged to your system PenMount Monitor Menu Icon The PenMount monitor icon (PM) appears in the menu bar of Windows 2000/XP system when you turn on PenMount Monitor in PenMount Utilities.
PenMount Monitor has the following function PenMount Rotating Functions The PenMount driver for Windows 2000/XP supports several display rotating software packages. Windows Me/2000/XP support display rotating software packages such as: • Portrait’s Pivot Screen Rotation Software • ATI Display Driver Rotate Function • nVidia Display Driver Rotate Function • SMI Display Driver Rotate Function • Intel 845G/GE Display Driver Rotate Function Configuring the Rotate Function 1.
NOTE: The Rotate function is disabled if you use Monitor Mapping APC-3X65 User Manual 80
