APC-3098/3298A/3598A Panel PC User Manual Release Date _ Jun. 2011 ® 2011 Aplex Technology, Inc. Revision V1.0 All Rights Reserved. Published in Taiwan Aplex Technology, Inc. 15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan Tel: 886-2-82262881 Fax: 886-2-82262883 E-mail: aplex@aplex.com.tw URL: www.aplex.com.
Warning!____________________________________ Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
� The equipment has obvious signs of breakage. 14. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20° C OR ABOVE 70° C. IT MAY DAMAGE THE EQUIPMENT. This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, it may cause interference to radio communications.
Table of Contents______________________ Warning!…………………………………………………………………………….……..….2 Disclaimer………………………………………………………………….…………………2 Chapter 1 Getting Started 1.1 Specifications……………………………………….……………………..6 1.2 Dimensions………………………………...………………………….......8 1.3 Brief Description…………………………………………………….……11 Chapter 2 Hardware 2.1 Mainboard………………..…….……………………………………..…..12 2.2 Jumpers and Connectors Location……………………………………...13 2.3 Jumpers Setting and Connectors……………...………………………13 Chapter 3 BIOS Setup 3.
Figure 1.2: APC-3298A Dimensions……………………..……………………..9 Figure 1.3: APC-3598A Dimensions…………………….…………………….10 Figure 1.4: Front View ………………………………………………………….11 Figure 1.5: Rear View…………………………………………………………...11 Figure 2.1: Mainboard Overview………………………………………….....12 Figure 5.1 Birdeye’s View of Control Board………………..
Chapter 1 System 1.1 Specifications Specs APC-3098 APC-3298A APC-3598A CPU Intel Atom Z510p 1.1 GHz FSB 400 MHz, Z530p 1.6 GHz FSB 533 MHz for option Chipset Intel US15WP System Memory On board 1 GB DDR2 400 MHz Graphic Intel integrated Graphics GMA500 External I/O Port 2 x USB 2.0 ports 2 x USB 2.0 ports Standard I/O： 2 x RJ-45 LAN ports 1 x RJ-45 LAN port 2 x USB 2.
Certificate APC-3X98(A) User Manual CE/FCC Class A 7
1.2 Dimensions Figure 1.
Figure 1.
Figure 1.
1.3 Brief Description of the APC-3098/3298A/3598A The APC-3098/3298A/3598A is a fanless design panel PC, which comes with an 8-inch (luminance of 350 cd/m²)/12-inch (luminance of 350 cd/m²)/15-inch (luminance of 350 cd/m²) TFT LCD. It is powered by an Intel Atom Z510P Processor. The industrial panel PC also features two COM ports, two USB 2.0 ports, one 2.5” HDD, one CF slot, DC power of 9~32V, etc. It is ideal for use as a PC-based controller for Industrial Automation & Factory Automation. Figure 1.
Chapter 2 Hardware 2.1 Mainboard Figure 2.
2.2 Jumpers and Connectors Location 2.3 Jumpers Setting and Connectors 1. 2. JP5: (2.0mm Pitch 1X2 Pin Header), ATX Power and AT Power setting jumper. PWR1: JP5 Mode Open ATX Power Mode Close AT Power Mode (5.
2 Ground Note: Make sure that the voltage of power supply is DC9V~30V before power on, or it may cause boot up failure and even system damage. 3. BAT1: (1.25mm Pitch 1X2 box Pin Header) 3.0V Li battery is embedded to provide power for CMOS. 4. Pin# Signal Name Pin1 VBAT PIN2 Ground USB23/USB45: (Double stack USB type A), Rear USB connector, it provides up to 4 USB2.0 ports, speed up to 480Mb/s. 5. LAN1: (RJ45 Connector), Rear LAN port, 1 standard 10/100/1000M RJ-45 Ethernet ports are provided.
3-5 ( Close) 4-6 ( Close) 9-11 ( Close) RS422 10-12 ( Close) 17-18 (Close) 3-5 ( Close) 4-6 ( Close) 15-16 (Close) RS485 7. COM1: (Type DB9), Rear serial port, standard DB9 serial port is provided to make a direct connection to serial devices. COM1 port is controlled by pins No.1~18 of JP485, select output Signal RS232 or RS422 or RS485, for details, please refer to description of JP485.
2 RXD (Received Data) 3 TXD (Transmit Data) 4 DTR (Data Terminal Ready) 5 Ground 6 DSR (Data Set Ready) 7 RTS (Request To Send) 8 CTS (Clear To Send) 9 JP3 Setting: Pin1-2 : RI (Ring Indicator) (default) Pin3-4 : 5V Standby power (option) Pin5-6: 12V Standby power (option) 9. JP3: (2.0mm Pitch 2x3 Pin Header), COM1 setting jumper, pin 1~6 are used to select signal out of pin 9 of COM3 port.
Note: Pin6 is backlight control signal, support DC or PWM mode, mode select at BIOS CMOS menu. 12. LVDS1: For 18/24 bit LVDS output connector, fully supported by Intel US15W chipset, the interface features dual channel 18/24-bit output. Model name of the interface connector is Hirose DF13-40DP-1.25V. Signal Name 13.
Expansion SMB bus. ·RS232(COM2,COM4): Expansion serial ports are provided to make a direct connection to serial devices.
HD LED+ 1 2 POWER LED+ HD LED- 3 4 POWER LED- Ground 5 6 PWR_ON RESET+ 7 8 Ground WAN LED- 9 10 WAN LED+ Pin1-3: HDD LED, They are used to connect hard disk activity LED. The LED blinks when the hard disk is reading or writing data. Pin2-4: POWER LED, They are used to connect power LED. When the system is powered on or under S0/S1 state, the LED is normally on; when the system is under S4/S5 state, the LED is off. Pin5-6: POWER on/off Button, They are used to connect power switch button.
18. JP2: (2.0mm Pitch 2x3 Pin Header), SATA1/SATA2/CF Devices Master or slave jumper setting. SATA1/ SATA2/ CF devices can only be used two at the same time, and the Master device can be set one only. While using SATA1/SATA2 devices at the same time, one of the devices must be set as Master. JP2 Devices Master 1~2 on 3~4 off CF Master 5~6 off 1~2 off 3~4 on SATA1 Master 5~6 off 1~2 off 3~4 off SATA2 Master 5~6 on 19. MPCIE1: (50.
□ TB515 (option): ASB-B705 SDVO1 connected Card, Support SDVO to CRT display and HDMI TV display TB515 Location VGA2 Port Signal Name: VGA2 G2 N2 CRT_BLUE CRT_GREEN CRT_RED CRT_DDCCLK CRT_DDCDATA CRT_VSY NC CRT_HSY NC 10 9 8 7 6 5 4 3 2 1 GND BLUE GREEN RED GND DDCCLK DDCDATA VSY NC HSY NC RSV G2 N2 10 1 CVBS_SY NC_OUT N1 G1 N1 G1 DF14A-10P-1.
HDTV2 Port Signal Name: □ TB516(option): ASB-B705 SDVO1 connected Card, Support dual channel 18/24 bit LVDS output connector. 2LB_D1_N 2LB_D1_P 2LB_D2_N 2LB_D2_P 2LB_CLKN 2LB_CLKP 2LDDC_DATA G2 G2 2LB_D3_N 2LB_D3_P N1 VCC5 VCC5 GND GND VCC3 VCC3 B_D0A_D0B_D0+ A_D0+ GND GND B_D1A_D1B_D1+ A_D1+ GND GND B_D2A_D2B_D2+ A_D2+ GND GND B_CLKA_CLKB_CLK+ A_CLK+ GND GND DDC_DATA DDC_CLK GND GND B_D3A_D3B_D3+ Aplex, A_D3+ RSV RSV 10.07.
. H3/H4/H5/H6: Intel Atom Z530P(or Z510P) CPU+ US15W Heat Sink SCREW HOLES, Four screw holes for Intel CPU and US15W Heat Sink assemble. 24. LED1/LED2: LED STATUS. LED1:Motherboard Standby Power Good status 。 LED2: Motherboard CPU Power Good status. 25. USB67: (2.0mm Pitch 2x5 Pin Header),Front USB connector, it provides two USB ports via a dedicated USB cable, speed up to 480Mb/s. USB6 and USB7 can only be used for internal device attachment as USB 2.0 SpecIfication, Can not support USB1.
Chapter 3 BIOS Setup 3.1 Operations after POST Screen After CMOS discharge or BIOS flashing operation, the system will display the following screen for your further operation. Press Delete key to enter CMOS Setup. AMIBIOS© 2006 American Mega trends , Inc. BIOS Date: 02/23/11 23:27:33 Ver: 08.00.15 CPU : Intel(R) Atom(TM) CPU Z510 @ 1.10GHz Speed : 600M Hz Press F11 for BBS POPUP Initializing USB Controllers. . 1019MB OK Done.
Please select boot device： Network: IBA GE Slot 0100 v1353 ↑and ↓ to move selection ENTER to select Boot device ESC to boot using defaults 3.2 BIOS SETUP UTILITY Press [Del] key to enter BIOS Setup utility during POST, and then a main menu containing system summary information will appear. BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit System Overview User [ENTER]，[TAB] AMIBIOS or Version : 08.00.
System Date 02/23/2011] CMC [Wed ESC Exit LO-Module:0D2.023x, Hi-Module:0d2.016x v02.61 © Copyright 1985-2006 American Megatrends , Inc. 3.3 System Overview BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit System Overview User [ENTER]，[TAB] AMIBIOS or Version [SHIFT-TAB] to Select a field : 08.00.15 Build Date : 02/23/11 ID Use[+] or [-] to : B705M003 configure system Time. Processor Intel(R) Atom(TM) CPU 1.
3.4 Advanced Settings BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Advanced Settings Exit Configure CPU WARNING: Setting wrong values In below sections may cause system to malfunction. ► CPU Configuration ► IDE Configuration ► Super IO Configuration ► ACPI Configuration ► MPS Configuration ← Select Screen ► PCI Express Configuration ↑↓ Select Item ► Smbios Configuration Enter Charge Field ► USB Configuration F1 General Help F10 Save and Exit ESC Exit V02.
Max CPUID Value Limit Intel (R) Virtualization Tech [Disabled] [Enabled] Execute-Disable Bit Capability [Enabled] F10 [Enabled] [Disabled] [Disabled] ESC Hyper Threading Technology Intel(R) SpeedStep (tm) tech Intel(R) C-SATAE tech +- Charge Field F1 General Help Save and Exit Exit V02.61 © Copyright 1985-2006 American Mega trends , Inc.
ATA/IDE Configuration [Compatible] Disabled Compatible ► Primary IDE Master Detected] : [Not ► Primary IDE Slaver Detected] : [Not Hard Disk Write Protect [Disabled] IDE Detect Time Out (Sec) [35] ATA(PI) 80Pin Cable Detection Device] ← Select Screen ↑↓ Select Item +- Charge Field F1 General Help F10 [Host & ESC Save and Exit Exit V02.61 © Copyright 1985-2006 American Mega trends , Inc.
Serial Port1 Address [3F8] Serial Port Base Serial Port1 Mode [RS-232] Address. Serial Port2 Address [2F8] Serial Port3 Address [3E8] Serial Port3 IRQ [IRQ4] Serial Port4 Address [2E8] Serial Port4 IRQ [IRQ3] ← Select Screen ↑↓ Select Item +- Charge Field F1 General Help F10 ESC Save and Exit Exit V02.61 © Copyright 1985-2006 American Mega trends , Inc. Serial Port1 Mode: COM1 Options: [RS232 ] [RS485] [RS232] for RS232 Mode [RS485] for RS485/RS422 Mode 3.4.
[Chipset ACPI Configuration]: APIC ACPI SCI IRQ: [Disabled] [Enabled] USB Device Wakeup From S3/s4: [Disabled] [Enabled] 3.4.5 MPS Configuration BIOS SETUP UTILITY Advanced MPS Configuration Select MPS MPS Revision [1.4] Revision ← Select Screen ↑↓ Select Item +- Charge Field F1 General Help F10 Save and Exit ECS Exit V02.61 © Copyright 1985-2006 American Mega trends , Inc. MPS Revision: [1.4] [1.1] 3.4.
F1 General Help F10 Save and Exit ESC Exit V02.61 © Copyright 1985-2006 American Mega trends , Inc. Active State Power Management: [Disabled] [Enabled] 3.4.7 Smbios Configuration BIOS SETUP UTILITY Advanced Smbios Configuration SMBIOS SMI Wrapper Smbios Smi Support [Enabled] Support for PnP Func 50h-54h ← Select Screen ↑↓ Select Item +- Charge Field F1 General Help F10 Save and Exit ESC Exit V02.61 © Copyright 1985-2006 American Mega trends , Inc.
option disables legacy USB Devices Enabled : 1Keyboard support if no USB devices are connected Legacy USB Support USB2.0 Controller Mode BIOS EHCI Hand-Off [Enabled] [HiSpeed] [Enabled] ← Select Screen ↑↓ Select Item +- Charge Field F1 General Help F10 Save and Exit ESC Exit V02.61 © Copyright 1985-2006 American Mega trends , Inc. Legacy USB Support: [Enabled] [Disabled] USB2.0 Controller Mode: [HiSpeed] [FullSpeed] BIOS EHCI Hand-Off: [Enabled] [Disabled] 3.
Clear NVRAM [No] Plug & Play O/S [No] PCI Latency Timer [64] Allocate IRQ to PCI VGA [Yes] Palette Snooping [Disabled] PCI IDE BusMaster [Disabled] OffBoard PCI/ISA IDE Card [Auto] ← Select Screen ↑↓ Select Item IRQ4 [Available] +- Charge Field F1 General Help IRQ5 [Available] F10 IRQ3 [Available] ESC Save and Exit Exit IRQ7 [Available] IRQ9 [Available] IRQ10 [Available] IRQ11 [Available] V02.61 © Copyright 1985-2006 American Mega trends , Inc.
[248] Allocate IRQ to PCI VGA: [Yes] [No] Palette Snooping: [Disabled] [Enabled] PCI IDE BusMaster: [Disabled] [Enabled] OffBoard PCI/ISA IDE Card: Some PCI IDE cards may require this to be set to the PCI slot number that is holding the card. Auto:Works for most PCI IDE Cards. [Auto] [PCI Slot1] [PCI Slot2] [PCI Slot3] [PCI Slot4] [PCI Slot5] [PCI Slot6] IRQ3/4/5/7/9/10/11/14/15: [Available] [Reserved] Available: Specified IRQ is available to be used by PCI/PnP devices.
[32k] [64k] 3.6 Boot Settings BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Boot Settings Chipset Exit Configure Settings During System Boot ► Boot Setting Configuration ► Boot Device Priority ► Hard Disk Drives ← Select Screen ↑↓ Select Item Enter Go to sub screen F1 F10 ESC General Help Save and Exit Exit V02.61 © Copyright 1985-2006 American Mega trends , Inc. Boot Setting Configuration： Configure Settings during System Boot.
AddOn ROM Display Mode: Set display mode for Option ROM. [Force BIOS] [Keep Current] Bootup Num-Lock: Select Power-on state for Numlock. [On] [Off] Wait For ‘F1’ If Error: Wait for F1 key to be pressed if error occurs. [Enabled] [Disabled] Hit ‘DEL’Messgae Display : Displays “press” DEL to run Setup in POST. [Enabled] [Disabled] Interrupt 19 Capture: Enabled: Allows option ROMs to trap interrupt 19. [Disabled] [Enabled] Boot Device Priority: Specifies the Boot Device Priority sequence.
Change User Password Boot Sector Virus Protection [Disabled] ← Select Screen ↑↓ Select Item Enter Charge F1 General Help F10 Save and Exit ESC Exit V02.61 © Copyright 1985-2006 American Mega trends , Inc. Change Supervisor Password: Install or Change the password. Change User Password: Install or Change the password. Boot Sector Virus Protection: [Disabled] [Enabled] Enabled / Disabled Boot Sector Virus Protection. Type the password with up to 6 characters and then press Enter key.
3.8 Advanced Chipset Settings BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Advanced Chipset Settings Exit Configure North Bridge WARNING: Setting wrong values in below sections may cause system to malfunction feature ► North Bridge Configuration ← Select Screen ↑↓ Select Item ► South Bridge Configuration Enter Go to sub screen F1 General Help F10 Save and Exit ESC Exit V02.61 © Copyright 1985-2006 American Mega trends , Inc.
V02.61 © Copyright 1985-2006 American Mega trends , Inc.
[External CRT] [External LVDS] Flat Panel Type: [1024x 768 18bit ] [640x480 18bit ] [800x600 18bit ] [1280x768 18bit ] [1280x800 18bit ] [1024x 768 24bit ] Backlight Control Support [VBIOS-Default] [Both BLC & BIA Disabled] [BLC Enabled] Panel Backlight Control: [Level9] [Level0] [Level1] [Level2] [Level3] [Level4] [Level6] [Level7] [Level8] [Level9] [Level10] [Level11] [Level12] [Level13] [Level14] [Level15] [Level16] Note: Panel support PWM Function.
[DPST Disabled] [DPST Enabled at Level] [DPST Enabled at Leve2] [DPST Enabled at Leve3 [DPST Enabled at Leve4] [DPST Enabled at Leve5] TV Standard: [VBIOS-Default] [NTSC] [PAL] [SECAM] [SMPTE240M] [ITU-R television] [SMPTE296M] [CEA 7702] [CEA 7703] 3.8.2 South Bridge Configuration: BIOS SETUP UTILITY Chipset South Bridge Chipset Configuration Number of UCHI USB Functions Ports] [8 USB Ports in system ECHI ONLY is USB2.0 Controller [Enabled] Automatically USB Client Controller [Disabled] Assed.
[8 USB Ports] [Disabled]， [2 USB Ports] [4 USB Ports] [6 USB Ports] USB 2.
3.9 Exit Options BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Options Save Changes and Exit Discard Changes and Exit Exit Exit system setup after saving the changes Discard Changes F10 key can be used Load Optimal Defaults For this operation Load Failsafe Defaults ← Select Screen ↑↓ Select Item Enter Go to sub screen F1 General Help F10 Save and Exit ESC Exit V02.61 © Copyright 1985-2006 American Mega trends , Inc.
Load Optimized Defaults: Load Optimized Defaults? (F9 key can be used for this operation) [OK] [Cancel] Load FailSafe Defaults: Load FailSafe Defaults? (F9 key can be used for this operation) [OK] [Cancel] APC-3X98(A) User Manual 45
Chapter 4 Installation of Drivers This chapter describes the installation procedures for software and drivers under the windows XP. The software and drivers are included with the motherboard. The contents include Intel chipset driver VGA driver LAN drivers Audio driver Installation instructions are given below.
4.1 Intel Chipset Driver To install the Intel chipset driver, please follow the steps below. Step 1: Select Chipset from the list Follow the step-by-step installation process to install the LMS_SQL driver.
APC-3X98(A) User Manual 48
Click Finish, When the installation process is complete, the Setup Complete screen appears. See as picture.
4.2 Intel Graphics Media Accelerator Driver To install the VGA drivers, follow the steps below to proceed with the installation. 1. Click Intel(R) US15W Chipset Family Graphics Driver. Follow the step-by-step installation process to install the Graphics Media Accelerator driver.
APC-3X98(A) User Manual 51
Click FINISH; A Driver Installation Complete.
4.3 Intel 8257L Gbe LAN Device Driver To install the Intel R 8257L Gbe Gigabit LAN connect device driver, please follow the steps below. Select LAN from the list Follow the step-by-step installation process to install the LAN driver.
APC-3X98(A) User Manual 54
Click FINISH; A Driver Installation Complete.
4.4 Realtek HD Audio Driver Installation To install the Realtek High Definition (HD) Audio driver, please follow the steps below. Select Audio from the list Follow the step-by-step installation process to install the Realtek HD Audio driver.
Click FINISH; A Driver Installation Complete.
Chapter 5 Touch Screen Installation This chapter describes how to install drivers and other software that will allow your PenMount 6000 Controller Board to work with different operating systems. NOTE: PenMount USB drivers support up to 15 USB controllers. 5.1 Introduction to Touch Screen Controller Board PenMount 6300 USB control board is a touch screen control board designed for USB interface and specific for 4, 5, 8-wire touch screens.
5.2.1 Installing Software If you have an older version of the PenMount Windows 2000/XP driver installed in your system, please remove it first. Follow the steps below to install the PenMount DMC6000 Windows 2000/XP driver. 1. Please make sure your PenMount 6000 device had plugged in advance. If your device uses RS232 interface, please plugged in before the machine is turned on. When the system first detects the controller board, a screen appears that shows “Unknown Device”. Do not use this hardware wizard.
3. A License Agreement appears. Click “I Agree…” and “Next” 4. Ready to Install the Program.
5.
6. The “Install Shield Wizard Completed” appears. Click “Finish”.
5.2.2 Software Functions Upon rebooting, the computer automatically finds the new 6000 controller board. The touch screen is connected but not calibrated. Follow the procedures below to carry out calibration. 1. After installation, click the PenMount Monitor icon “PM” in the menu bar. 2. When the PenMount Control Panel appears, select a device to “Calibrate.
Advanced Calibration Advanced Calibration uses 4, 9, 16 or 25 points to effectively calibrate touch panel linearity of aged touch screens. Click this button and touch the red squares in sequence with a stylus. To skip, press ESC’. Command Calibration Command call calibration function. Use command mode call calibration function, this can uses Standard, 4, 9, 16 or 25 points to calibrate E.g. Please run ms-dos prompt or command prompt c:\Program Files\PenMount Universa Driver\Dmcctrl.
NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an accurate calibration. Use a stylus during Advanced Calibration for greater accuracy. Please follow the step as below: 3.Come back to “PenMount Control Panel” and select “Tools” then Click “Advanced Calibration”.
Select “Device” to calibrate, then you can start to do “Advanced Calibration”. NOTE: Recommend to use a stylus during Advanced Calibration for greater accuracy.
Setting APC-3X98(A) User Manual 67
About This panel displays information about the PenMount controller and driver version.
Multiple Monitors Multiple Monitors supports from two to six touch screen displays for one system. The PenMount drivers for Windows 2000/XP support Multiple Monitors. This function supports from two to six touch screen displays for one system. Each monitor requires its own PenMount touch screen control board, either installed inside the display or in a central unit. The PenMount control boards must be connected to the computer COM ports via the RS-232 interface.
3. Touch each screen as it displays “Please touch this monitor. Press ‘S’ to skip” Following this sequence and touching each screen is called mapping the touch screens. 4. After the setting procedure is finished, maybe you need to calibrate for each panel and controller NOTES: 1. If you used a single VGA output for multiple monitors, please do not use the Multiple Monitors function. Just follow the regular procedure for calibration on each of your desktop monitors. 2.
Tools Draw Tests or demonstrates the PenMount touch screen operation. Advanced Calibration Enable Advanced Calibration function Right Button Icon Enable right button function. The icon can show on Desktop or System Tray (menu bar).
PenMount Monitor Menu Icon The PenMount monitor icon (PM) appears in the menu bar of Windows 2000/XP system when you turn on PenMount Monitor in PenMount Utilities. PenMount Monitor has the following function PenMount Rotating Functions The PenMount driver for Windows 2000/XP supports several display rotating software packages.
Windows Me/2000/XP support display rotating software packages such as: • Portrait’s Pivot Screen Rotation Software • ATI Display Driver Rotate Function • nVidia Display Driver Rotate Function • SMI Display Driver Rotate Function • Intel 845G/GE Display Driver Rotate Function Configuring the Rotate Function 1. Install the rotation software package. 2. Choose the rotate function (0°, 90°, 180°, 270°) in the 3rd party software. The calibration screen appears automatically.
