APC-3X19 User Manual Release Date Revision Apr 2014 ® 2014 Aplex Technology, Inc. Taiwan V2.3 All Rights Reserved. Published in Aplex Technology, Inc. 15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan Tel: 886-2-82262881 Fax: 886-2-82262883 E-mail: aplex@aplex.com.tw www.aplex.com.
Warning!____________________________ This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, it may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
Packing List Accessories (as ticked) included in this package are: □ Power Connector □ Driver & manual CD disc □ Other.___________________(please specify) Safety Precautions Follow the messages below to avoid your systems from damage: ◆ Avoid your system from static electricity on all occasions. ◆ Prevent electric shock. Don‘t touch any components of this card when the card is power-on. Always disconnect power when the system is not in use. ◆ Disconnect power when you change any hardware devices.
Table of Contents__________ Warning!…………………………………………………………………….……..….2 Disclaimer………………………………………………………….…………………2 Packing List.......................................................................................................3 Safety Precautions............................................................................................3 Chapter 1 Getting Started 1.1 Specifications……………...………………….………….……...…..6 1.2 Dimensions…………...……………...……………….…………......7 1.3 Brief Description of APC-3X19…..……………….
Figures Figure 1.1: Dimensions of APC-3519………..………………………...7 Figure 1.2: Dimensions of APC-3719 ….…….……..………………....8 Figure 1.3: Dimensions of APC-3919 ….…….……..………………....9 Figure 1.4: Front View of APC-3x19.….…….……..………………....10 Figure 1.5: Rear View of APC-3x19.….…….……..………………....10 Figure 2.1: Mainboard Dimensions……...…………………..……..…11 Figure 2.2: Jumpers and Connectors Location-TOP……………..…19 Figure 2.3: Jumpers and Connectors Location- Bottom………....
Chapter 1_____________Getting Started 1.1 Specifications Model No. Specs APC-3519 APC-3719 APC-3919 System System Chipset Intel G2 socket, support up to 3rd Gen Core i7 3630QM 2.4GHz Processor Intel HM77 System Memory 2 x 204 Pin DDR3 SO-DIMM, up to 16GB 1066/1333 MHz Storage 2 x 2.5" SATA HDD space, easily accessible storage design 1 x external CF slot Processor External I/O USB Serial/Parallel Audio Graph LAN Digital I/O KB/MS Membrane Control Power 4 x USB 2.
Power Consumption Max:51.3W Max:44.2W Max:44.2W Mechanical Structure IP Rating Mounting Black steel front bezel, black steel back cover with aluminum heat-sink Panel IP65 Panel Mount/ VESA 75x75 VESA 100x100 410x310x119 439x348x119 484x400x115 8.9 kg 9.8 kg 12.1 kg Dimensions (WxHxD) (mm) Gross Weight Environmental 0~50 ﾟ C -20~60 ﾟ C 10~90% @40 ﾟ C non-condensing CE/FCC Class A Operating Temperature Storage Temperature Storage Humidity Certificate 1.2 Dimensions Figure 1.
Figure 1.
Figure 1.
1.3 Brief Description of APC-3X19 APC-3x19 is a fanless and high-performance panel-mount industrial panel PC with 15”/17/19” TFT LCD. It is powered by Intel HM77 chipset and support Core i3/i5/i7 Processor up to i7 3630QM 2.4GHz. The panel PC has a rich variety of functions and peripherals. It supports DDR3 memory up to 8GB, rich I/O ports, and a wide range 9~32V DC input. APC-3x19 also provides 1 x PCIe x 16 or 1 x PCI slot, ensuring simplified connectivity to a variety of external peripheral devices.
1.4 Installation of HDD Step 1 There are 2 screws to deal with when enclosing or removing the HDD bracket. Step 2 There is 1 screw to deal with when enclosing or removing the HDD Tray.
Step 4 Tighten four screws as shown in the picture. F Screw M3*5L 120° Step 5 Push into the HDD bracket as shown in the picture Step 6 That’s how it should look after it has been installed.
1.5 Installation of Riser Card Step 1 There are 2 screws to deal with when enclosing or removing the bracket. Step 2 Remove the cover. Step 3 Loosen the screw.
Step 4 Put the riser card in. Put the riser card in. Put the riser card in.
Step 5 Tighten two screws.
Chapter 2_____ __Hardware Installation 2.1 Mainboard Specifications Introduction ASB-M8771 is a Mini-ITX industrial motherboard developed on the basis of Intel QM77/HM77,which provides abundant peripheral interfaces to meet the needs of different customers. Also, it features dual GbE ports, 6-COM ports and one Mini PCIE configuration. To satisfy the special needs of high-end customers, ADOtec designed 120Pin PCIe x16 and 40Pin PCIe x1expansion interface.
Specifications Board Size 170mm x 170mm CPU Support Support Socket G2, 2nd/3rd Gen Intel Core i3/i5/i7 Processors Chipset Intel HM77 (ASB-M8771H) Memory Support 2 x SO-DIMM (204pins), up to 16GB DDRIII 1066/1333/1600MHz FSB Graphics Intel HD Graphics 4000 Super I/O Winbond W83627UHG BIOS AMIBIOS 16M Storage 1 x SATA2.0 Connector 1 x SATA2.0 Connector 2 x SATA3.0 Connector 1 x CFAST Slot 1 x MSATA Connector Ethernet 2 x PCIe GbE LAN by Intel 82574L USB 4 x USB 2.
Digital I/O 8-bit digital I/O by Pin header by MIO2 4-bit digital Input 4-bit digital Output Battery Support CR2477 Li battery by 2-pin header Support CR2032 Li battery (BAT2,option) Audio Support Audio via Realtek ALC662 HD audio codec Support Line-out, MIC by JACK1 Support Line-in, Line-out, MIC by 2x6-pin header Keyboard /Mouse PS2 K/B and Mouse by MIO2 1 x PS/2 keyboard 1 x PS/2 mouse Expansion 1 x PCI-express x16 extend by 4x30 pin socket 2 x PCI-express x1 extend by 4x10 pin socket 1 x mini-P
Power Consumption 12V/3.80A (Intel i5-2430M 2.4GHz Processor with 4GB DDR3) 19V/2.0A (Intel i5-2540 2.6GHz Processor with 8GB DDR3) 19V/2.2A(Intel i7-2620 2.7GHz Processor with 8GB DDR3) EMI/EMS Meet CE/FCC class A 2.2 Jumpers Setting and Connectors Figure 2.
Figure 2.
1. RTC1/SRTC1: (2.0mm Pitch 1X2 Pin Header)CMOS clear jumper, CMOS clear operation will permanently reset old BIOS settings to factory defaults. RTC1/SRTC1 CMOS Open or （RTC1Pin1-SRTC1 Pin close） NORMAL (Default) Close 1-2 Clear CMOS Procedures of CMOS clear: a) Turn off the system and unplug the power cord from the power outlet. b) To clear the CMOS settings, use the jumper cap to close pins1 and 2 for about 3 seconds then reinstall the jumper clip back to pins open. c) Power on the system again.
5. DCIN: (5.08mm Pitch 1x3 Pin Connector),DC9V ~ DC32V System power input connector。 Pin# Power Input Pin1 DC+9V~32V Pin2 Ground Pin3 PG 6. ATX12V_IN (ATX Power option): (2x2 Pin Connector), DC12V System power input connector. 7. ATX Pin# Power input Pin1 Ground Pin2 Ground Pin3 DC+12V Pin4 DC+12V (ATX Power option): (2.0mm Pitch 1X3 box Pin Header), connect PSON and 5VSB and Ground signal,support ATX Power model. Reserved.
Pin1 DC+12V Pin2 Ground Pin3 Ground Pin4 DC+5V 9. U1: (Socket G2), installing the 2nd GEN intel Core i3/i5/i7CPU Socket. 10. CPU_FAN1/SYS_FAN1: (2.54mm Pitch 1x3 Pin Header),Fan connector, cooling fans can be connected directly for use. You may set the rotation condition of cooling fan in menu of BIOS CMOS Setup. Pin# Signal Name 1 Ground 2 VCC 3 Rotation detection Note: Output power of cooling fan must be limited under 5W. 11.
Pin# Signal Name 1 +DC12V 2 +DC12V 3 Ground 4 Ground 5 BKLT_EN 6 BKLT_CTRL Note: Pin6 is backlight control signal, support DC or PWM mode, mode select at BIOS CMOS menu. 14. LVDS1: (1.25mm Pitch 2x20 Connector), For 18/24-bit LVDS output connector, Fully supported by Intel QM67 chipset, the interface features dual channel 18/24-bit output.
15. HDMI1: (HDMI 19P Connector), High Definition Multimedia Interface connector. 16. DVI-I: (DVI-I Connector), Digital Visual Interface-Integrated connector. 17. BT1: POWER on/off Button, They are used to connect power switch button. The two pins are disconnected under normal condition. You may short them temporarily to realize system startup & shutdown or awaken the system from sleep state. 18. JP1: (2.
20. COM1: (Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a direct connection to serial devices.
21. JP2: (2.0mm Pitch 2x3 Pin Header),COM2 jumper setting, pin 1~6 are used to select signal out of pin 9 of COM2 port. JP2 Pin# Function Close 1-2 COM2 Pin9 RI (Ring Indicator) (default) Close 3-4 COM2 Pin9=+5V (option) Close 5-6 COM2 Pin9=+12V (option) 22. COM2: (Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a direct connection to serial devices.
Close 1-2 COM6 Pin9 RI (Ring Indicator) (default) Close 3-4 COM6 Pin9=+5V (option) Close 5-6 COM6 Pin9=+12V (option) 25. COM6: (2.0mm Pitch 2x5 Pin Header), COM6 Port, standard RS232 ports are provided. They can be used directly via COM cable connection. COM6 port is controlled by pins No.1~6 of JP3,select output Signal 5V or 12v, For details, please refer to description of JP3.
or amplifier, MIC is the port for microphone input audio. 28. AUDIO1: (2.0mm Pitch 2X6 Pin Header), Front Audio, An onboard Realtek ALC662 codec is used to provide high-quality audio I/O ports. Line Out can be connected to a headphone or amplifier. Line In is used for the connection of external audio source via a Line in cable. MIC is the port for microphone input audio.
MODEL PC1E16X / PCIE1X ASB-M8771T Top ASB-M8771B Bottom 35. M-PCIE1: (Socket 52Pin),mini PCIe socket, it is located at the top, it supports mini PCIe devices with USB2.0,SIM,SMBUS and PCIe signal. MPCIe card size is 30x30mm or 30 x 50.95mm. 36. H2/H1(option): MPCIE1 SCREW HOLES, H1 for mini PCIE card (30mmx30mm) assemble. H2 for mini PCIE card (30mmx50.95mm) assemble. 37. BUZZER1: Onboard buzzer. 38.
39. MIO2: (DF13-40P Connector),Front panel connector.
Pin11~Pin18: GPIO IN/GPIO OUT, General-purpose input/output port, it provides a group of self-programming interfaces to customers for flexible use. Pin19~Pin24: PS2 KB/MS, PS/2 keyboard and mouse port, the port can be connected to PS/2 keyboard and mouse via a dedicated cable for direct used. Pin25~40: USB0/USB1/USB2/USB3, Front USB connector, it provides 4 USB ports via a dedicated USB cable, speed up to 480Mb/s.
42. SATA1/SATA2/SATA3/SATA4: (SATA 7P), SATA Connectors, Four SATA connectors are provided,SATA3 and SATA4 transfer speed up to 3.0Gb/s, SATA1 and SATA2 transfer speed up to 6.0Gb/s. RAID controller supporting RAID 0/1/5/10. Position Function Color SATA1 SATA3.0 White or Blue SATA2 SATA3.0 White or Blue SATA3 SATA2.0 black SATA4 SATA2.0 black（NC） 43. CFAST (option): (CFAST Card socket), it is located at the bottom of the board and serves as an insert interface for CFAST card. 44.
50. TB-525E161: TB-525E161 connect to ASB-M8771T PCIE_16X connector, PCIE_16X is located at the top,It provides one PCIE X16 slot. 51. TB-525P1: TB-525P1 connect to ASB-M8771T PCIE1X connector, PCIE1X is located at the top,It provides one PCI slot.
Chapter 3 BIOS Setup 3.1 Operations after POST Screen After CMOS discharge or BIOS flashing operation,.Press [Delete] key to enter CMOS Setup. Version 2.15.1227. Copyright (C) 2012 American Megatrends, Inc. ( L8771V07 ) Press 〈DEL〉or〈F2〉to enter setup CMOS Checksum fail。Press ＜DEL＞ to enter setup。 A3 After optimizing and exiting CMOS Setup, the POST screen displayed for the first time is as follows and includes basic information on BIOS, CPU, memory, and storage devices. 3.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset System Language Boot Security [English] Save & Exit Choose the system Default language System Date [Tue 01/01/2009] System Time [00:00:08] Access Level Administrator →←: Select Screen BIOS Information Project Version L8771V07 Build Date and Time 04/03/2013 01:51:14 ↑↓ X64 : Select Item Enter: Select +/- : Charge Opt.
3.4 Advanced Settings Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit PCI,PCI-X and PCI ►PCI Subsystem Settings Express Setting.
[Disabled] [Enabled] PERR# Generation: [Disabled] [Enabled] SERR# Generation: [Disabled] [Enabled] PCI Express Device Settings： 3.4.2 ACPI Settings Enable ACPI Auto Configuration: [Disabled] [Enabled] Enable Hibernation: [Enabled] [Disabled] ACPI Sleep State: [Both S1 and S3 avai…] [Suspend Disabled] [S1 only (CPU Stop clock)] [S3 only (Suspend to RAM ] Lock Legacy Resources: [Disabled] [Enabled] S3 Video Repost: [Disabled] [Enabled] 3.4.
Hyper-threaading [Enabled] [Disabled] Active Processor Cores [All] [1] Limit CPUID Maximum: [Disabled] [Enabled] Execute Disable Bit: [Enabled] [Disabled] Intel Virtualization Technology [Enabled] [Disabled] Hardware Prefetcher [Enabled] [Disabled] Adjacent Cache Line Prefetch [Enabled] [Disabled] 3.4.
IDE legacy / Native Mode Selection [Native] [Legacy] Serial ATA Port 0 Software Preserve Empty Unknown Serial ATA Port 1 Software Preserve Empty Unknown Serial ATA Port 2 Software Preserve Empty Unknown Serial ATA Port 3 Software Preserve Empty Unknown Serial ATA Port 4 Software Preserve Empty Unknown Serial ATA Port 5 Software Preserve Empty Unknown 3.4.5 Thermal Configuration Platform Thermal Configuration 3.4.6 Intel(R) Rapid Start Technology Intel(R) Rapid Start Technology [Disabled] 3.
1 keyboard, 2 Hubs Legacy USB Support: [Enabled] [Disabled] EHCI Hand-off: [Disabled] [Enabled] Port 60/64 Emulation [Enabled] [Disabled] USB hardware delays and time-outs: USB transfer time-out: [20 sec] [10 sec] [5 sec] [1 sec] Device reset time-out: [20 sec] [10 sec] [30 sec] [40 sec] Device power-up delay [Auto] [Manual] 3.4.
+12V +3.3V +1.5V AVCC : +12.160 V : +3.296 V : +1.520 V : +5.158 V 3.4.13 Platform Misc Configuration 3.4.14 Intel(R) Smart Connect Technology 3.4.15 Serial Port Console Redirection 3.4.16 Intel RC Drivers Version Detail 3.4.
3.5 Chipset Settings Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit System Agent (SA) ►System Agent (SA) Configuration Parameters ►PCH-IO Configuration →←: Select Screen ↑↓ Enter: : Select Item Select +/- : Charge Opt. F1 : General Help F2: Previous Values F3:Optimized Defaults F4:Save and Exit ESC Exit Version 2.15.1227. Copyright (C) 2012 American Megatrends , Inc. 3.5.
[Enabled] GTT Size [2MB] [1MB] Aperture Size [256MB] [128MB] [512MB] DVMT Pre-allocated [64MB] [32MB] [96MB] [128MB] [160MB] [192MB] [224MB] [256MB] [288MB] [320MB] [352MB] [384MB] [416MB] [448MB] [480MB] [512MB] [1024MB] Dvmt Total Gfx Mem [256MB] [128MB] [MAX] GFX Low Power Mode [Enabled] [Disabled] Primary IGFX Boot Display [VBIOS Default] [VGA] [DVI] [LVDS] LCD Panel Type [1280 X 1024 24bit 2ch] [640 X 480 18bit 1ch] [800 X 480 18bit 1ch] [800 X 600 18bit 1ch] 44
[800 X 600 24bit 1ch] [1024 X 768 18bit 1ch] [1024 X 768 24bit 1ch] [1280 X 800 18bit 1ch] [1366 X 768 18bit 1ch] [1440 X 900 24bit 2ch] [1600 X 900 24bit 2ch] [1600 X 1200 24bit 2ch] [1680 X 1050 24bit 2ch] [16800 X 1050 24bit 2ch] [1920 X 1080 24bit 2ch] [2048 X 1536 24bit 2ch] Panel Scaling [Auto ] [Off ] [Force Scaling ] Backlight Control [DC ] [PWM] Backlight Logic [Positive ] [Negaive] Backlight Control Control Level [Level 8 ] [Level 0 ] [Level 1 ] [Level 2 ] [Level 3 ] [Level 4 ] [Level 5 ] [Level 6
PEG0 PEG0 – Gen X [Not Present] [Auto] [Gen1] [Gen2] [Gen3] PEG ASPM [Auto] [Disabled] [Auto] [ASPM LOs] [ASPM L1] [ASPM LOsL1] De-emphasis Control [-3.5 dB] [-6 dB] ►Memory Configuration Memory RC Version 1.6.6.
[Enabled] Wark on LAN [Enabled] [Disabled] Board Capability [SUS_PWR_DN_ACK] [Deepsx] SLP_S4 Assertion Width [4-5 Seconds] [1-2 Seconds] [2-3 Seconds] [3-4 Seconds] Restore AC Power Loss [Power off] Set NAND Management Override [Enabled] [Disabled] ►PCI Express Configuration PCI Express Clock Gating [Enabled] [Disabled] DMI Link ASPM Control [LOSL1] [LOS] [Disabled] DMI Link Extended Synch Control [Disabled] [Enabled] Subtractive Decode [Disabled] [Enabled] ►PCI Express Root Port 1 ►PCI Express Root Port 2
3.6 Boot Settings Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Boot Configuration Save & Exit Number of seconds to Setup Prompt Timeout 1 Wait for setup Bootup Numlock State [On] Activation key. 65535(0xFFFF)means Quiet Boot [Disabled] Fast Boot [Disabled] CSM16 Module Version 07.69 Gatea20 Active [Upon Request] Option ROM Messages [Force BIOS] →←: Select Screen INT19 Trap Response [Immediate] ↑↓ Indef inite waiting.
Option ROM Messages [Force BIOS] [Keep Current] Interrupt 19 Capture [Immediate] [Postponed] Boot Option Priorities ►CSM parameters 3.7 Security Settings Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Password Description Save & Exit Set Administrator Password If ONLY the Administrator’s password is set, Then this only limits access to Setup and is Only asked for when entering Setup.
A confirmation message will be shown on the screen as to whether the password will be disabled. You will have direct access to BIOS setup without typing any password after system reboot once the password is disabled. Once the password feature is used, you will be requested to type the password each time you enter BIOS setup. This will prevent unauthorized persons from changing your system configurations.
[No] Save Changes and Reset Save & reset Save Configuration and reset? [Yes] [No] Discard Changes and Reset Reset Without Saving Reset without saving? [Yes] [No] Save Changes Save Setup Values Save configuration? [Yes] [No] Discard Changes Load Previous Values Load Previous Values? [Yes] [No] Restore Defaults Load Optimized Defaults Load optimized Defaults? [Yes] [No] Save user Defaults Save Values as User Defaults Save configuration? [Yes] [No] Restore user Defaults Restore User Defaults Restore User Defau
Chapter 4 Installation of Drivers Important Note: After installing your Windows operating system (Windows XP), you must install first the Intel Chipset Software Installation Utility before proceeding with the installation of drivers.
4.1 Intel Chipset Driver To install the Intel chipset driver, please follow the steps below. Step 1. Access Industrial Panel PC. Select Intel QM77&HM77 Chipset Driver. Step 2. Click Next to setup program.
Step 3. Read the license agreement. Click Yes to accept the terms of the license agreement. Step 4. Click Next to continue.
Step 5. Click Next. Step 6. Select Yes, I want to restart this computer now. media from the drives.
4.2 Intel (R) VGA Chipset Driver To install the VGA drivers, follow the steps below to proceed with the installation. Step 1. Select Intel(R) VGA Chipset Driver. Step 2. Click Next to continue setup program.
Step 3. Check Automatically run WinSAT and enable the Windows Aero desktop theme (if supported.) Click Next to continue setup program. Step 4. Read the license agreement. APC-3X19 User Manual Click Yes to accept the license agreement.
Step 5. Click Next. Step 6. Click Next.
Step 7. Select Yes, I want to restart this computer now. Click Finish.
4.3 Intel(R) Network Adapter Driver Step 1. Select Intel(R) Network Adapter. Step 2. Click Next to continue.
Step 3. Read the license agreement. click Next to continue. Select I accept the terms in the license agreement then Step 4. Select Drivers, Intel(R) PROSet for Windows* Device Manager, Advanced Network Services. Click Next to continue.
Step 5. Click Install to begin the installation. Step 6. Click Finish to compete the installation.
4.4 Realtek HD Audio Driver Installation To install the Realtek High Definition (HD) Audio driver, please follow the steps below. Step 1. Select Realtek ALC662 HD Audio Codec Driver from the list. Step 2. Wait for extracting the files then click Next to continue.
Step 3. Select Yes, I want to restart my computer now. then click Finish.
4.5 Intel(R) USB 3.0 Driver Step 1. Select Intel(R) USB 3.0 Driver Step 2. Click Next to continue.
Step 3. Read the license agreement. Click Yes to continue. Step 4. Click Next to continue.
Step 5. Click Next to continue. Step 6. Select Yes, I want to restart this computer now. Click Finish.
4.6 Intel(R) AMT Driver Step 1. Select Intel(R) AMT Driver Step 2. Click Next to continue.
Step 3. Read the license agreement. Click Yes to continue. Step 4. Click Next to continue.
Step 6. Click Finish to compete the setup.
Chapter 5 Touch Screen Installation This chapter describes how to install drivers and other software that will allow your PenMount 6000 Controller Board to work with different operating systems. NOTE: PenMount USB drivers support up to 15 USB controllers. 5.1 Introduction to Touch Screen Controller Board PenMount 6300 USB control board is a touch screen control board designed for USB interface and specific for 4, 5, 8-wire touch screens.
5.2.1 Installing Software If you have an older version of the PenMount Windows 2000/XP driver installed in your system, please remove it first. Follow the steps below to install the PenMount DMC6000 Windows 2000/XP driver. Step 1. Please make sure your PenMount 6000 device had plugged in advance. If your device uses RS232 interface, please plugged in before the machine is turned on. When the system first detects the controller board, a screen appears that shows “Unknown Device”.
Step 3. Click Next to continue. Step 4. Read the license Agreement. APC-3X19 User Manual Click I agree to agree the license agreement.
Step 5. Choose the folder in which to install PenMount Windows Universal Driver. Click Install to start the installation. Step 6. Wait for installation. Then click Next to continue.
Step 7. Click Continue Anyway to continue. Step 8. Click Finish to compete installation.
5.2.2 Software Functions Upon rebooting, the computer automatically finds the new 6000 controller board. The touch screen is connected but not calibrated. Follow the procedures below to carry out calibration. 1. After installation, click the PenMount Monitor icon “PM” in the menu bar. 2. When the PenMount Control Panel appears, select a device to “Calibrate.
Advanced Calibration Advanced Calibration uses 4, 9, 16 or 25 points to effectively calibrate touch panel linearity of aged touch screens. Click this button and touch the red squares in sequence with a stylus. To skip, press ESC’. Command Calibration Command call calibration function. Use command mode call calibration function, this can uses Standard, 4, 9, 16 or 25 points to calibrate E.g. Please run ms-dos prompt or command prompt c:\Program Files\PenMount Universa Driver\Dmcctrl.
Step 2. Click Standard Calibration to start calibration procedure NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an accurate calibration. Use a stylus during Advanced Calibration for greater accuracy.
Step 3. Come back to PenMount Control Panel and select Tools then Click Advanced Calibration. Step 4. Select Device to calibrate, then you can start to do “Advanced Calibration”. NOTE: Recommend to use a stylus during Advanced Calibration for greater accuracy.
Setting APC-3X19 User Manual 80
About This panel displays information about the PenMount controller and driver version.
Multiple Monitors Multiple Monitors supports two to six touchscreen displays for one system. PenMount drivers for Windows 2000, XP 32/64bit, and 2003 support Multiple Monitors. This function supports from two to six touchscreen displays for one system. Each monitor requires its own PenMount touchscreen control board, either installed inside the displayor in a central unit. The PenMount control boards must be connected to the computer COM ports via the RS-232 interface.
Step 2. When the mapping screen message appears, click OK.
Step 3. Touch each screen as it displays Please touch this monitor. Press ‘S’ to skip Following this sequence and touching each screen is called mapping the touch screens. Step 4. After the setting procedure is finished, maybe you need to calibrate for each panel and controller. NOTES: 1. If you used a single VGA output for multiple monitors, please do not use the Multiple Monitors function. Just follow the regular procedure for calibration on each of your desktop monitors. 2.
About You can see how many devices of PenMount controller that are plugged to your system PenMount Monitor Menu Icon The PenMount monitor icon (PM) appears in the menu bar of Windows 2000/XP system when you turn on PenMount Monitor in PenMount Utilities.
PenMount Monitor has the following function PenMount Rotating Functions The PenMount driver for Windows 2000/XP supports several display rotating software packages. Windows Me/2000/XP support display rotating software packages such as: • Portrait’s Pivot Screen Rotation Software • ATI Display Driver Rotate Function • nVidia Display Driver Rotate Function • SMI Display Driver Rotate Function • Intel 845G/GE Display Driver Rotate Function Configuring the Rotate Function 1.
NOTE: The Rotate function is disabled if you use Monitor Mapping APC-3X19 User Manual 87
