APC-3X19 User Manual Release Date Revision Jan 2013 ® 2013 Aplex Technology, Inc. V1.0 All Rights Reserved. Published in Taiwan Aplex Technology, Inc. 15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan Tel: 886-2-82262881 Fax: 886-2-82262883 E-mail: aplex@aplex.com.tw APC-3X19 User Manual URL: www.aplex.com.
Warning!_______________________________ This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, it may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
Packing List Accessories (as ticked) included in this package are: □ AC power cable □ Driver & manual CD disc □ Other.___________________(please specify) Safety Precautions Follow the messages below to avoid your systems from damage: ◆ Avoid your system from static electricity on all occasions. ◆ Prevent electric shock. Don‘t touch any components of this card when the card is power-on. Always disconnect power when the system is not in use. ◆ Disconnect power when you change any hardware devices.
Table of Contents______________________ Warning!…………………………………………………………………………….……..….2 Disclaimer………………………………………………………………….…………………2 Packing List...................................................................................................................3 Safety Precautions........................................................................................................3 Chapter 1 Getting Started 1.1 Specifications………………………………………….………….……...…..6 1.2 Dimensions…………………………………...……………….…………......
4.2 Intel (R) VGA Chipset Driver..…................…......……………….......…..62 4.3 Intel(R) Network adapter Driver…........…..................................……….67 4.4 Realtek HD Audio Driver Installation………………….…………………71 4.5 Microsoft .NET Framework 3.5 Service.................................................73 Chapter 5 Touch Screen Installation 5.1 Introduction to Touch Screen Controller Board………………………....75 5.2 Windows 2000/XP USB Driver Installation………………….………..….75 Figures Figure 1.
Chapter 1________________Getting Started 1.1 Specifications Model No. APC-3519 Specs APC-3719 APC-3919 System Processor Support Socket G2, 2nd Generation Intel Core i7/i5/i3, up to i7 Quad core 2710QE System Chipset Intel QM67 PCH System Memory 2 x SO-DIMM(204pins) up to 16GB DDRIII 1066/1333MHz FSB Storage 2 x 2.5" SATA HDD space External I/O Port Onboard 2 x DB9 RS-232 (COM1.2) 1 x DVI-I 1 x HDMI 2 x RJ45 GbE LAN 4 x USB 2.
View Angle 160:145 Backlight Lifetime 50,000 hrs 170:160 170:165 Touch Screen Type Resistive Touch Light Transmission 80% Power Supply Power Input DC 9~32V Mechanical Construction Steel black IP Rating Front Panel IP65 Mounting Panel mount/VESA 75 x 75/VESA 100 x 100 Dimensions (WxHxD) (mm) 410x310x116 439x348x119 484x400x119 Environmental Operating Temperature 0~50 ﾟ C Storage Temperature -20~60 ﾟ C Storage Humidity 10~90% @40 ﾟ C non-condensing Certificate CE/FCC Class A APC-
1.2 Dimensions Figure 1.1: Dimensions of APC-3519 Figure 1.
Figure 1.
1.3 Brief Description of APC-3X19 The APC-3x19 is the fanless and high performance panel-mount industrial panel PC with 15”/17/19” TFT LCD. It powered by QM67 chipset and support Core i3/i5/i7 Processor up to i7 Quad core 2710QE. The panel PC has a rich variety of functions and peripherals. It comes with 2 x 2.
1.4 Installation of HDD Step 1 There are 2 screws to deal with when enclosing or removing the HDD bracket. Step 2 There is 1 screw to deal with when enclosing or removing the HDD Tray.
Step 3 Loosen screw and draw the HDD bracket out as shown in the picture Step 4 Tighten four screws as shown in the picture.
Step 5 That’s how it should look after it has been installed.
1.5 Installation of Riser Card Step 1 There are 2 screws to deal with when enclosing or removing the bracket. Step 2 Remove the cover.
Step 3 Loosen the screw. Step 4 Put the riser card in. Step 5 Tighten two screws.
Chapter 2__________Hardware Installation 2.1 Mainboard Specifications Introduction Figure 2.
Figure 2.2: Mainboard Dimensions ASB-M8671 is a Mini-ITX industrial motherboard developed on the basis of Intel QM67,which provides abundant peripheral interfaces to meet the needs of different customers. Also, it features dual GbE ports, 6-COM ports and one Mini PCIE configuration. To satisfy the special needs of high-end customers, ADOtec designed 120Pin PCIe x16 and 40Pin PCIe x1 expansion interface. The product is widely used in various sectors of industrial control. 2.
Storage 4 x SATA Connector 1 x CFAST Slot (option) Ethernet 2 x PCIe Gbe LAN by Intel 82574L USB 4 x USB 2.0 stack ports for external 3 x USB 2.0 box Pin header for MIO1 4 x USB 2.0 box Pin header for MIO2 1 x USB 2.
HDD LED status by MIO2 External I/O port 2 x COM Ports (COM1/COM2) 4 x USB 2.0 Ports (stack) 2 x RJ45 GbE LAN Ports 1 x DVI-I Port 1 x HDMI Port 1 x Audio Ports (Mic, Line out) Watchdog Timer Software programmable 1 – 255 second by Super I/O Temperature Operating: -20℃ to 70℃ Storage: -40℃ to 85℃ Humidity 10% - 90%, non-condensing, operating Power Consumption EMI/EMS 12V/3.80A (Intel i5-2430M 2.4GHz Processor with 4GB DDR3) Meet CE/FCC class A 2.2 Jumpers Setting and Connectors Figure 2.
Figure 2.4: Jumpers and Connectors Location- Bottom 1. RTC1/SRTC1: (2.0mm Pitch 1X2 Pin Header)CMOS clear jumper, CMOS clear operation will permanently reset old BIOS settings to factory defaults. RTC1/SRTC1 CMOS Open or NORMAL (Default) （RTC1Pin1-SRTC1 Pin close） Close 1-2 Clear CMOS Procedures of CMOS clear: a) Turn off the system and unplug the power cord from the power outlet.
3. Pin# Signal Name Pin1 VBAT Pin2 Ground PS_SEL: (2.0mm Pitch 1X3 Pin Header),ATX Power and AT Power jumper setting. PS_SEL Mode Close 1-2 Close 2-3 4. ATX Power (Default) AT Power PS_ON: (2.0mm Pitch 1X3 Pin Header),ATX Power and Auto Power on jumper setting. PS_ON Mode Close 1-2 Auto Power on (Default) Close 2-3 5. ATX Power DCIN: (5.08mm Pitch 1x3 Pin Connector),DC9V ~ DC32V System power input connector。 6.
7. Pin# Power input Pin1 Ground Pin2 Ground Pin3 DC+12V Pin4 DC+12V ATX (ATX Power option): (2.0mm Pitch 1X3 box Pin Header), connect PSON and 5VSB and Ground signal,support ATX Power model. Reserved. 8. Pin# Signal Name Pin1 ATX PSON Pin2 ATX Ground Pin3 ATX 5VSB DC_OUT: (2x2 Pin Connector),DC12V and DC5V System power output connector. 9. Pin# Power output Pin1 DC+12V Pin2 Ground Pin3 Ground Pin4 DC+5V U1: (Socket G2), installing the 2nd GEN intel Core i3/i5/i7CPU Socket.
1 Ground 2 VCC 3 Rotation detection Note: Output power of cooling fan must be limited under 5W. 11. A-DDR3/B-DDR3: (SO-DIMM 204Pin socket), DDRIII memory socket, the socket is located at the Top of the board and supports 204Pin 1.5V DDRIII 1066/1333MHz FSB SO-DIMM memory module up to 16GB. 12. VGA1: (CRT 2.0mm Pitch 2X5 Pin Header), Video Graphic Array Port, Provide 2x5Pin cable to VGA Port. Signal Name 13.
14. LVDS1: (1.25mm Pitch 2x20 Connector), For 18/24-bit LVDS output connector, Fully supported by Intel QM67 chipset, the interface features dual channel 18/24-bit output.
19. BT1: POWER on/off Button, They are used to connect power switch button. The two pins are disconnected under normal condition. You may short them temporarily to realize system startup & shutdown or awaken the system from sleep state. 20. JP1: (2.0mm Pitch 2x3 Pin Header),COM1 jumper setting, pin 1~6 are used to select signal out of pin 9 of COM1 port. JP1 Pin# 21.
RS232 (Default): Pin# Signal Name 1 DCD# (Data Carrier Detect) 2 RXD (Received Data) 3 TXD (Transmit Data) 4 DTR (Data Terminal Ready) 5 Ground 6 DSR (Data Set Ready) 7 RTS (Request To Send) 8 CTS (Clear To Send) 9 JP1 select Setting (RI/5V/12V) RS422 (option): Pin# Signal Name 1 422_R- 2 422_R+ 3 422_T- 4 422_T+ 5 Ground 6 NC 7 NC 8 NC 9 NC RS485 (option): Pin# 23. Signal Name 1 NC 2 NC 3 485- 4 485+ 5 Ground 6 NC 7 NC 8 NC 9 NC JP2: (2.
JP1 Pin# 24. Function Close 1-2 COM2 RI (Ring Indicator) (default) Close 3-4 COM2 Pin9=+5V (option) Close 5-6 COM2 Pin9=+12V (option) COM2: (Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a direct connection to serial devices. Pin# 25.
27. Close 1-2 COM6 RI (Ring Indicator) (default) Close 3-4 COM6 Pin9=+5V (option) Close 5-6 COM6 Pin9=+12V (option) COM6: (2.0mm Pitch 2x5 Pin Header), COM6 Port, standard RS232 ports are provided. They can be used directly via COM cable connection. COM6 port is controlled by pins No.1~3 of JP3,select output Signal 5V or 12v, For details, please refer to description of JP3.
. JACK1: (Diameter 3.5mm Double stack Jack), HD Audio port, An onboard Realtek ALC662 codec is used to provide high quality audio I/O ports. Line Out can be connected to a headphone or amplifier, MIC is the port for microphone input audio. 30. AUDIO1: (2.0mm Pitch 2X6 Pin Header), Front Audio, An onboard Realtek ALC662 codec is used to provide high-quality audio I/O ports. Line Out can be connected to a headphone or amplifier.
35. PCIE1X (option): (4x10 Pin),Riser Card expansion connector.Can expand support two PCIe Signal. ASB-M8671T：PCIE1X connector in the top. ASB-M8671B：PCIE1X connector in the Bottom. 36. MODEL PC1E16X / PCIE1X ASB-M8671T Top ASB-M8671B Bottom M-PCIE1: (Socket 52Pin),mini PCIe socket, it is located at the top, it supports mini PCIe devices with USB2.0, SMBUS and PCIe signal. MPCIe card size is 30x30mm or 30x50.95mm. 37. H1/H2: MPCIE1 SCREW HOLES, H1 for mini PCIE card (30mmx30mm) assemble.
40. Ground 28 27 Ground Ground 30 29 Ground Power 3P3V_S0 32 31 5V_USB_1011 LED PWR_LED- 34 33 USB11_N Power MIO_PSON 36 35 USB11_P Button Ground 38 37 Ground NC 40 39 NC USB11 MIO2: (DF13-40P Connector),Front panel connector.
Pin7- Ground: RESET Button, They are used to connect reset button. The two pins are disconnected under normal condition. You may short them temporarily to realize system reset. Pin6- Pin8: POWER on/off Button, They are used to connect power switch button. The two pins are disconnected under normal condition. You may short them temporarily to realize system startup & shutdown or awaken the system from sleep state. Pin9- Pin10: BUZZER, They are used to connect an external buzzer.
Pin# Signal Name 1 +DC5V 2 Ground 3 Ground 4 +DC12V Note: Output current of the connector must not be above 1A. 43. SATA1/SATA2/SATA3/SATA4: (SATA 7P), SATA Connectors, Four SATA connectors are provided,SATA1 and SATA2 transfer speed up to 6.0Gb/s, SATA3 and SATA4 transfer speed up to 3.0Gb/s,RAID controller supporting RAID 0/1/5/10. 44. CFAST (option): (CFAST Card socket), it is located at the bottom of the board and serves as an insert interface for CFAST card. 45.
TB-525E161 connect to ASB-M8671T PCIE_16X connector, PCIE_16X is located at the top,It provides one PCIE X16 slot.
Chapter 3 BIOS Setup 3.1 Operations after POST Screen After CMOS discharge or BIOS flashing operation, press [Delete] key to enter CMOS Setup. A3 After optimizing and exiting CMOS Setup, the POST screen displayed for the first time is as follows and includes basic information on BIOS, CPU, memory, and storage devices. 3.2 BIOS SETUP UTILITY Press [Delete] key to enter BIOS Setup utility during POST, and then a main menu containing system summary information will appear.
BIOS Information Choose the system BIOS Vendor American Megatrends Core Version 4.6.4.0 Compliancy UEFI 2.1 Project Version M8671V01 Build Date and Time 05/21/2012 16:15:28 System Language [English] Default language X64 →←: Select Screen System Date [Sun 07/10/2012] ↑↓ System Time [00:00:08] Enter: : Select Item Select +/- : Charge Opt. Access Level Administrator F1 : General Help F2: Previous Values F3:Optimized Defaults F4:Save and Exit ESC Exit Version 2.10.1208.
→←: Select Screen System Date [Sun 07/10/2012] ↑↓ System Time [00:00:08] Enter: : Select Item Select +/- : Charge Opt. Access Level Administrator F1 : General Help F2: Previous Values F3:Optimized Defaults F4:Save and Exit ESC Exit Version 2.10.1208. Copyright (C) 2010 American Megatrends , Inc.
►USB Configuration →←: Select Screen ►W83627UHG Super IO Configuration ↑↓ ► HW Monitor Enter: ►Sandybridge PPM Configuration +/- : Charge Opt. : Select Item Select F1 : General Help F2: Previous Values F3:Optimized Defaults F4:Save and Exit ESC Exit Version 2.10.1208. Copyright (C) 2010 American Megatrends , Inc. 3.4.1 PCI Subsystem Settings PCI Bus Driver Versio V2.03.
[Disabled] [Enabled] Extended Tag: [Disabled] [Enabled] No Snoop: [Enabled] [Disabled] Maximum Payload: [Auto] [128 Bytes] [256 Bytes] [512 Bytes] [1024 Bytes] [2048 Bytes] [4096 Bytes] Maximum Read Request: [Auto] [128 Bytes] [256 Bytes] [512 Bytes] [1024 Bytes] [2048 Bytes] [4096 Bytes] PCI Express Link Settings: ASPM Support: [Disabled] [Enabled] WARNING:Ebabling ASPM may cause some PCI-E devices to fail Extended Synch: [Disabled] [Enabled] 3.4.
[Disabled] ACPI Sleep State: [S3 (Suspend to RAM)] [Suspend Disabled] [S3 (Suspend to RAM)] Lock Legacy Resources: [Disabled] [Enabled] 3.4.3 CPU Configuration Socket 0 CPU Information: Intel(R) Core(TM) i5-2430M CPU @2.
[Disabled] Hardware Prefetcher [Enabled] [Disabled] Adjacent Cache Line Prefetch [Enabled] [Disabled] Intel Virtualization Technology [Enabled] [Disabled] 3.4.
Serial ATA Port 5 Software Preserve Empty Unknown 3.4.5 Thermal Configuration Platform Thermal Configuration 3.4.6 PCH-FW Configuration ME FW Version 0.0.0.0 ME Firmware Mode ME Firmware Type Full Sku Firmware ME Firmware SKU Unidentified ME Firmware Update Configuration ME FW Image Re-Flash [Disabled] [Enabled] 3.4.
[30 sec] [40 sec] Device power-up delay [Auto] [Manual] 3.4.8 W83627UHG Super IO Configuration W83627UHG Super IO Configuration Super IO Chip Winbond W83627UHG COM1 Configuration COM2 Configuration COM3 Configuration COM4 Configuration COM5 Configuration COM6 Configuration 3.4.9 HW Monitor PC Health Status System temperature CPU temperature CPU Fan Speed VCORE +12V : +48 C : +52 : 6000 RPM : +1.145V : +11.685 V +3.3V +1.5V 5VSB VBAT : +3.280 V : +1.520 V : +5.010 V : +3.136 V 3.4.
CPU C6 report [Enabled] [Disabled] CPU C7 report Long duration power limit Long duration maintained Short duration power limit TCC active offset [Enabled] [Disabled] 0 28 0 0 3.5 Chipset Settings Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit System Agent (SA) ►System Agent (SA) Configuration Parameters ►PCH-IO Configuration →←: Select Screen ↑↓ : Select Item Enter: Select +/- : Charge Opt.
VT-d Capability CHAP Device (B0:D7:F0) Unsupported [Enabled] [Disabled] Thermal Device (B0:D4:F0) [Disabled] [Enabled] Enable NB CRID [Disabled] [Enabled] ►Graphics Configuration IGFX VBIOS Version IGFX Frequency Graphics Turbo IMON Current Primary Display 2120 650 MHz 31 [Auto] [IGFX] [PEG] [PCI] Internal Graphics [Auto] [Disabled] [Enabled] GTT Size [2MB] [1MB] Aperture Size [256MB] [128MB] [512MB] DVMT Pre-allocated [64MB] [0MB] [32MB] [96MB] [128MB] [160MB] [192MB] [224MB] [256MB] APC-3X19 User Manu
[288MB] [320MB] [352MB] [384MB] [416MB] [448MB] [480MB] [512MB] Dvmt Total Gfx Mem [256MB] [128MB] [MAX] GFX Low Power Mode [Enabled] [Disabled] LCD Control: Primary IGFX Boot Display [VBIOS Default] [CRT] [DVI] [LVDS] HDMI] LCD Panel Type APC-3X19 User Manual [1024 X 768 [640 X 480 [800 X 600 [1280 X 1024 [1400X1050(RB) [1400X1050 [1600 X 1200 [1366 X 768 [1680 X 1050 [1920 X 1200 [1440 X 900 LVDS1] LVDS ] LVDS] LVDS] LVDS1] LVDS2] LVDS] LVDS] LVDS] LVDS] LVDS] [1600 X 900 [1024 X 768 [1280 X 800 [1920
SDVD-LFP Panel Type [VBIOS [1024 x 768 Default] SDVO-LFP ] [1080 x1024 [1400 x 1050 [1600 x 1200 SDVO-LFP ] SDVO-LFP ] SDVO-LFP ] Panel Scaling [Auto ] [Off ] [Force Scaling ] Backlight Control [PWM Inverted ] [PWM Normal ] [GMBus Inverted ] [GMBus Normal ] BIA [Auto ] [Disabled ] [Level 1 ] [Level 2 ] [Level 3 ] [Level 4 ] [Level 5 ] Spread Spectrum clock chip [Off ] [Hardware ] [Software ] TV1 Standard [VBIOS Default] [NTSC_M] [NTSC_M_J] [NTSC_433] [PAL_B] [PAL_G] [PAL_D] [PAL_H] [PAL_I] [PAL_M] [PAL_
[SECAM_B] [SECAM_D] [SECAM_G] [SECAM_H] [SECAM_K] [HDTV_STD_SMPTE_240M_1080i59] [HDTV_STD_SMPTE_240M_1080i60] [HDTV_STD_SMPTE_295M_1080i50] [HDTV_STD_SMPTE_295M_1080p50] [HDTV_STD_SMPTE_296M_720p50] [HDTV_STD_SMPTE_296M_720p60] [HDTV_STD_CEAEIA_7702A_480p60 ] [HDTV_STD_CEAEIA_7702A_480i60] TV2 Standard [VBIOS Default] [NTSC_M] [NTSC_M_J] [NTSC_433] [PAL_B] [PAL_G] [PAL_D] [PAL_H] [PAL_I] [PAL_M] [PAL_N] [SECAM_L] [SECAM_B] [SECAM_D] [SECAM_G] [SECAM_H] [SECAM_K] [HDTV_STD_SMPTE_240M_1080i59] [HDTV_STD_SMPTE
ALS Support [Disabled] [Enabled] Active LFP [Int-LVDS] [No-LVDS] [SDVO LVDS] [eDP Port-A] [eDP Port-D] Panel Color Depth [18 Bit] [24 Bit] ►DMI Configuration ►NB PCIe Configuration PEG0 PEG0 – Gen X [Not Present] [Auto] [Gen1] [Gen2] PEG1 PEG1 – Gen X [Not Present] [Auto] [Gen1] [Gen2] PEG2 PEG2 – Gen X [Not Present] [Auto] [Gen1] [Gen2] PEG3 PEG3 – Gen X [Not Present] [Auto] [Gen1] [Gen2] Always Enable PEG [Disabled] [Enabled] PEG ASPM [Disabled] APC-3X19 User Manual 49
[Auto] [ASPM LOs] [ASPM L1] [ASPM LOsL1] ASPM LOs [Root Port Only] [Endpoint Port Only] [Both Root and Endpoint Ports] De-emphasis Control [-3.5 dB] [-6 dB] ►Memory Configuration Memory RC Version Memory Frequency Total Memory DIMM#0 DIMM#1 DIMM#2 DIMM#3 CAS Latency (tCL) Minimum delay time CAS to RAS (tRPmin) Row Precharge (tRPmin) Active to Precharge (tRPmin) DIMM profile 1.2.
[Disabled] Max TOLUD [Dynamic] [1GB] [1.25GB] [1.5GB] [1.75GB] [2GB] [2.25GB] [2.5GB] [2.75GB] [3GB] [3.
►Memory Thermal Configuration Memory Thermal Management [Enabled] [Disabled] PECI Injecred Temperature [Disabled] [Enabled] EXTTS# via TS-on-Board [Disabled] [Enabled] EXTTS# via TS-on-DIMM [Disabled] [Enabled] Virtual Temperature Sensor (VTS) [Disabled] [Enabled] ►GT-Power Management Control GT Info RC6 (Render Standby) GT2 (0X116) [Enabled] [Disabled] GT overClocking Support [Disabled] [Enabled] APC-3X19 User Manual 52
3.6 Boot Settings Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Main Advanced Chipset Boot Security Boot Configuration Save & Exit Number of seconds to Setup Prompt Timeout 1 Wait for setup Bootup Numlock State [On] Activation key. 65535(0xFFFF)means Quiet Boot [Disabled] Fast Boot [Enabled] Skip VGA [Disabled] Skip USB [Disabled] Skip PS2 [Disabled] CSM16 Module Version 07.68 Gatea20 Active [Upon Request] Indef inite waiting.
[Upon Request] [Always] Option ROM Messages [Force BIOS] [Keep Current] Interrupt 19 Capture [Disabled] [Enabled] Boot Override SATA PM: ST9320423AS …… Launch EFI Shell from filesystem device 3.7 Security Settings Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Main Advanced Chipset Boot Security Password Description Save & Exit Set Administrator Password If ONLY the Administrator’s password is set, Then this only limits access to Setup and is Only asked for when entering Setup.
3.7.2 User Password Type the password with up to 20 characters and then press Enter key. This will clear all previously typed CMOS passwords. You will be requested to confirm the password. Type the password again and press Enter key. You may press Esc key to abandon password entry operation. To clear the password, just press Enter key when password input window pops up. A confirmation message will be shown on the screen as to whether the password will be disabled.
Restore Defaults →←: Select Screen Save user Defaults ↑↓ Restore user Defaults Enter: : Select Item Select +/- : Charge Opt. Boot Override F1 : General Help SATA PM:*** … F2: Previous Values Launch EFI Shell from filesystem device F3:Optimized Defaults F4:Save and Exit ESC Exit Version 2.10.1208. Copyright (C) 2010 American Megatrends , Inc.
[Yes] [No] Restore user Defaults Restore User Defaults Restore User Defaults? [Yes] [No] Launch EFI Shell from filesystem device WARNING Not Found [ok] APC-3X19 User Manual 57
Chapter 4 Installation of Drivers This chapter describes the installation procedures for software and drivers under the windows XP. The software and drivers are included with the motherboard. The contents include Intel QM67 Chipset Driver, Intel (R) VGA Chipset Driver, Intel (R) Network Adapter, Realtek ALC662 Audio Codec Driver, Microsoft .NET Framework 3.5 Service, Touch Panel Driver. Installation instructions are given below.
4.1 Intel Chipset Driver To install the Intel chipset driver, please follow the steps below. Step 1. Access Industrial Panel PC. Select Intel QM67 Chipset Driver. Step 2. Click Next to setup program.
Step 3. Read the license agreement. Click Yes to accept the terms of the license agreement. Step 4. Click Next to continue.
Step 5. Click Next. Step 6. Select Yes, I want to restart this computer now. media from the drives.
4.2 Intel (R) VGA Chipset Driver To install the VGA drivers, follow the steps below to proceed with the installation. Step 1. Select Intel(R) VGA Chipset Driver. Step 2. Click Yes to continue.
Step 3. Click Next to continue setup program. Step 4. Read the license agreement. APC-3X19 User Manual Click Yes to accept the license agreement.
Step 5. Click Next. Step 6. Click Continue Anyway.
Step 7. Click Continue Anyway. Step 8. Click Next.
Step 9. Select Yes, I want to restart this computer now. Click Finish.
4.3 Intel(R) Network Adapter Driver To install the Intel 82574L Network adapter Driver, please follow the steps below. Step 1. Select Intel(R) Network Adapter. Step 1. Wait for extracting the files then click Next to continue.
Step 2. Click Next. Step 3. Read the license agreement. Next to continue.
Step 4. Select Drivers, Intel(R) PROSet for Windows* Device Manager, Advanced Network Services. Click Next to continue. Step 5. Click Install to begin the installation.
Step 6. Click Finish to compete the installation.
4.4 Realtek HD Audio Driver Installation To install the Realtek High Definition (HD) Audio driver, please follow the steps below. Step 1. Select Realtek ALC662 HD Audio Codec Driver from the list. Step 2. Wait for extracting the files then click Next to continue.
Step 3. Click Next to continue the installation. Step 4. Select Yes, I want to restart my computer now. then click Finish.
4.5 Microsoft .NET Framework 3.5 Service To install the Realtek High Definition (HD) Audio driver, please follow the steps below. Step 1. Select Microsoft .NET Framework 3.5 Service. Step 2. Select I have read and ACCEPT the terms of the License Agreement. APC-3X19 User Manual Click Install.
Step 2. Wait for installation. Step 3. Click Exit to complete the installation.
Chapter 5 Touch Screen Installation This chapter describes how to install drivers and other software that will allow your PenMount 6000 Controller Board to work with different operating systems. NOTE: PenMount USB drivers support up to 15 USB controllers. 5.1 Introduction to Touch Screen Controller Board PenMount 6300 USB control board is a touch screen control board designed for USB interface and specific for 4, 5, 8-wire touch screens.
Step 1. Please make sure your PenMount 6000 device had plugged in advance. If your device uses RS232 interface, please plugged in before the machine is turned on. When the system first detects the controller board, a screen appears that shows “Unknown Device”. Do not use this hardware wizard. Press Cancel. Step 2. Insert the Aplex product CD install setup.exe. the screen below would appear. Se touch panel driver Step 3. Click Next to continue.
Step 4. Read the license Agreement. Click I agree to agree the license agreement. Step 5. Choose the folder in which to install PenMount Windows Universal Driver. Click Install to start the installation.
Step 6. Wait for installation. Then click Next to continue. Step 7. Click OK.
Step 8. Click Finish to compete installation.
5.2.2 Software Functions Upon rebooting, the computer automatically finds the new 6000 controller board. The touch screen is connected but not calibrated. Follow the procedures below to carry out calibration. 1. After installation, click the PenMount Monitor icon “PM” in the menu bar. 2. When the PenMount Control Panel appears, select a device to “Calibrate.
Advanced Calibration Advanced Calibration uses 4, 9, 16 or 25 points to effectively calibrate touch panel linearity of aged touch screens. Click this button and touch the red squares in sequence with a stylus. To skip, press ESC’. Command Calibration Command call calibration function. Use command mode call calibration function, this can uses Standard, 4, 9, 16 or 25 points to calibrate E.g. Please run ms-dos prompt or command prompt c:\Program Files\PenMount Universa Driver\Dmcctrl.
Step 2. Click Standard Calibration to start calibration procedure NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an accurate calibration. Use a stylus during Advanced Calibration for greater accuracy.
Step 3. Come back to PenMount Control Panel and select Tools then Click Advanced Calibration. Step 4. Select Device to calibrate, then you can start to do “Advanced Calibration”. NOTE: Recommend to use a stylus during Advanced Calibration for greater accuracy.
Setting APC-3X19 User Manual 84
About This panel displays information about the PenMount controller and driver version.
Multiple Monitors Multiple Monitors supports two to six touchscreen displays for one system. PenMount drivers for Windows 2000, XP 32/64bit, and 2003 support Multiple Monitors. This function supports from two to six touchscreen displays for one system. Each monitor requires its own PenMount touchscreen control board, either installed inside the displayor in a central unit. The PenMount control boards must be connected to the computer COM ports via the RS-232 interface.
Step 2. When the mapping screen message appears, click OK.
Step 3. Touch each screen as it displays Please touch this monitor. Press ‘S’ to skip Following this sequence and touching each screen is called mapping the touch screens. Step 4. After the setting procedure is finished, maybe you need to calibrate for each panel and controller. NOTES: 1. If you used a single VGA output for multiple monitors, please do not use the Multiple Monitors function. Just follow the regular procedure for calibration on each of your desktop monitors. 2.
About You can see how many devices of PenMount controller that are plugged to your system PenMount Monitor Menu Icon The PenMount monitor icon (PM) appears in the menu bar of Windows 2000/XP system when you turn on PenMount Monitor in PenMount Utilities.
PenMount Monitor has the following function PenMount Rotating Functions The PenMount driver for Windows 2000/XP supports several display rotating software packages. Windows Me/2000/XP support display rotating software packages such as: • Portrait’s Pivot Screen Rotation Software • ATI Display Driver Rotate Function • nVidia Display Driver Rotate Function • SMI Display Driver Rotate Function • Intel 845G/GE Display Driver Rotate Function Configuring the Rotate Function 1.
NOTE: The Rotate function is disabled if you use Monitor Mapping APC-3X19 User Manual 91
