AHM-6159P User Manual Release Date _ Revision Jan. 2013 ® 2013 Aplex Technology, Inc. V1.0 All Rights Reserved. Published in Taiwan Aplex Technology, Inc. 15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan Tel: 886-2-82262881 Fax: 886-2-82262883 E-mail: aplex@aplex.com.tw AHM-6159P User Manual URL: www.aplex.com.
Warning!___________________________________ This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, it may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
Packing List Accessories (as ticked) included in this package are: □ AC power cable □ Driver & manual CD disc □ Other.___________________(please specify) Safety Precautions Follow the messages below to prevent your systems from damage: ◆ Avoid your system from static electricity on all occasions. ◆ Prevent electric shock. Don„t touch any components of this card when the card is power-on. Always disconnect power when the system is not in use. ◆ Disconnect power when you change any hardware devices.
Table of Contents______________________ Warning!…………………………………………………………………………….……..….2 Disclaimer………………………………………………………………….…………………2 Packing List…………………………………………………………………………………..3 Safety Precautions…………………………………………………………………………..3 Chapter 1 Getting Started 1.1 Specifications……………………………………..….……………………..6 1.2 Dimensions………………………………...………………………….......7 1.3 Brief Description…………………………………………………….……8 Chapter 2 Hardware 2.1 Mainboard………………..…….……………………………………..…..10 2.2 Installations…….………………….……………………………………...
Figures Figure 1.1: Dimensions of AHM-6159P………………………………..…....7 Figure 1.2: Front view of AHM-6159P…………………………………..…....8 Figure 1.3: Rear View of AHM-6159P………………………………………….8 Figure 2.1: Mainboard Dimensions…………………………………..…….....10 Figure 2.2: Jumpers and Connectors Location_ Board Top………………...11 Figure 2.3: Jumpers and Connectors Location_ Board Bottom…………....12 Figure 5.
Chapter 1 System 1.1 Specifications System Intel Socket P, default Intel P8400 2.24GHz Processor System Memory 1 X DDR3 SO-DIMM Slot, default 2GB System Chipset Intel GM45 + ICH9M Outside I/O ports Storage 4 x USB 2.
Mounting Panel and VESA 75 x 75 mount Dimension 410(W)x290(H)x40(D)mm Environmental Operating Temperature -10~50 °C Storage Temperature -20~60 °C Storage Humidity 10~90% @40 °C, non-condensing Certificate CE/FCC Class A 1.2 Dimensions Figure 1.
1.3 Brief Description of AHM-6159P AHM-6159P is a slim, fanless design PC, which comes with a 15-inch LCD. It is powered by an Intel Socket P Core 2 Duo Processor, up to Intel P8400 2.26GHz processor. The industrial panel PC also features two COM ports, four USB 2.0 ports, one 2.5” HDD, one internal CF slot, and 11~32V DC, etc. It is ideal for use as a PC-based controller for Industrial Automation & Factory Automation Figure 1.2: Front View of AHM-6159P Figure 1.
1.4 Installation of HDD Step 1 Gently remove two screws in back of the machine. Step 2 Insert HDD in the HDD bracket. Step 3 Insert CF in the CF bracket.
Step4 Tighten two crews. Chapter 2 Hardware 2.1 Mainboard Figure 2.
2.2 Installations ASB-L801 is a 4" industrial Embedded motherboard developed on the basis of Intel GM45+ ICH9M, which provides abundant peripheral interfaces to meet the needs of different customers. Also, it features dual 1000M LAN port, 5-COM port and dual Mini PCIE configuration. To satisfy the special needs of high-end customers, PC104+ port (capable of adjusting IO voltage) richer extension functions. Due to its compact size, the product is widely used in various sectors of industrial control.. 2.2.
Figure 2.3: Jumpers and Connectors Location_ Board Bottom 2.3 Jumpers Setting and Connectors 1. RTC/SRTC: (2.0mm Pitch 1X2 Pin Header)CMOS clear jumper, CMOS clear operation will permanently reset old BIOS settings to factory defaults. RTC/SRTC CMOS OPEN NORMAL (default) CLOSE 1-2 Clear CMOS Procedures of CMOS clear: 5.4.1.1 Turn off the system and unplug the power cord from the power outlet. 5.4.1.
3. BAT1: JP2 Mode Open ATX Power Mode Close Auto Power on (1.25mm Pitch 1X2 box Pin Header) 3.0V Li battery is embedded to provide power for CMOS. 4. Pin# Signal Name Pin1 VBAT PIN2 Ground F_PANEL: (2.0mm Pitch 2X5 Pin Header), Front panel connector. Signal Name Pin# Pin# Signal Name HD LED+ 1 2 POWER LED+ Ground 3 4 Ground Ground 5 6 SW+ RESET+ 7 8 Ground SPK+ 9 10 SPK- Pin1-3: HDD LED, They are used to connect hard disk activity LED.
Note: When connecting LEDs and buzzer, pay special attention to the signal polarity. Make sure that the connector pins have a one-to-one correspondence with chassis wiring, or it may cause boot up failure. 5. JP1: (2.0mm Pitch 1x3 Pin Header) COM5 setting jumper, pin 1~3 are used to select signal out of pin 10 of COM5 port. JP1 Pin# 6. COM5: Function Close 1-2 COM5 Pin10=+5V (default) Close 2-3 COM5 Pin10=+12V (option) (2.0mm Pitch 2X5 Pin Header), COM5 Port, standard RS232 ports are provided.
8. RTS 7 8 CTS RI 9 10 NC COM3: (2.0mm Pitch 1x6 box Pin Header),it provides selectable RS422/RS485 serial signal output. 9. JP3: RS422 Type (option) RS485 Type (default) Signal Name Pin# Pin# 422RX- 1 1 NC 422RX+ 2 2 NC 422TX- 3 3 485- 422TX+ 4 4 485+ Ground 5 5 Ground +5V 6 6 +5V Signal Name (2.0mm Pitch 2x3 Pin Header),COM1 setting jumper, pin 1~6 are used to select signal out of pin 9 of COM1 port.
4 DTR (Data Terminal Ready) 5 Ground 6 DSR (Data Set Ready) 7 RTS (Request To Send) 8 CTS (Clear To Send) 9 JP1 Setting: Pin1-2 : RI (Ring Indicator) (default) Pin3-4 : 5V Standby power Pin5-6:12V Standby power (option) 11. USB3/USB4: (option) (2.0mm Pitch 2X5 Pin Header) ,Front USB connector, it provides 4 USB ports via a dedicated USB cable, speed up to 480Mb/s.
13. AUDIO: (2.0mm Pitch 2X6 Pin Header), Front Audio, An onboard Realtek ALC662 codec is used to provide high-quality audio I/O ports. Line Out can be connected to a headphone or amplifier. Line In is used for the connection of external audio source via a Line in cable. MIC is the port for microphone input audio. Signal Name 14.
3 Rotation detection Note: Output power of cooling fan must be limited under 5W. 17. LAN1/2: (RJ45 Connector), Rear LAN port,2 standard 10/100/1000M RJ-45 Ethernet ports are provided. Used Intel 82574L chipset ,LINK LED (green) and ACTIVE LED (yellow) respectively located at the left-hand and right-hand side of the Ethernet port indicate the activity and transmission state of LAN. 18. CRT1: (CRT Connector DB15),Video Graphic Array Port, provide high-quality video output.
connector for LVDS1. Pin# Signal Name 1 +DC12V 2 +DC12V 3 Ground 4 Ground 5 BKLT_EN 6 BKLT_CTRL Note: Pin6 is backlight control signal, support DC or PWM mode, mode select at BIOS CMOS menu. 21. LVDS1: For 18/24 bit LVDS output connector, Fully supported by Intel GM45 chipset, the interface features dual channel 18/24-bit output. Model name of the interface connector is Hirose DF13-40DP-1.25V.
NC 22. DC_IN2: DC_IN1: 40 39 NC (5.0mm 1x2 Pin Connector),DC12V System power input connector。 Pin# Signal Name 1 +12V 2 Ground (2x2 box Pin Connector),DC12V System power input connector。 Pin# Signal Name 1 Ground 2 Ground 3 +12V 4 +12V Note: Make sure that the voltage of power supply is DC(12±5%)V before power on, or it may cause boot up failure and even system damage. 23.
24. SATA_P1: (2.5mm Pitch 1x2 box Pin Header),an onboard 5V output connector is reserved to provide power for IDE/SATA devices. Pin# Signal Name 1 +DC5V 2 Ground Note: Output current of the connector must not be above 1A. 25. JP_104P: (2.0mm Pitch 1X3 Pin Header) PC104+ port voltage selection jumper,select voltage for PCI-104 Plus device. The default for this jumper is “all open”,meaning the user must select the voltage to be used. 26.
status。LED3: Motherboard CPU Power Good status. 31. MPCIE1: (30mmx30mm Socket 52Pin),mini PCIE socket, it is located at the bottom, it supports mini PCI-E devices with USB2.0, SMBUS and PCI-E signal. 32. H5/H6: MPCIE1 SCREW HOLES, H5 for mini PCIE card (30mmx30mm Socket 52 Pin) assemble. H6 Reserve. 33. IDE_CF1: (CF Card socket), it is located at the bottom of the board and serves as an insert interface for Type I and Type II Compact Flash card. The operating voltage of CF card can be set as 3.
3 BIOS Setup Description 3.1 Operations after POST Screen After CMOS discharge or BIOS flashing operation, the system will display the following screen for your further operation. Press F2 key to continue or F1 key to enter CMOS Setup. AMIBIOS© 2006 American Mega trends , Inc. BIOS Date: 03/08/11 23:27:33 Ver: 08.00.15 CPU : Genuine Intel(R) CPU 575 Speed : 2.00 GHz Press F11 for BBS POPUP Initializing USB Controllers. . 2013MB OK @ 2.00GHz Done. Auto-Detecting Pri Master..
Checking NVRAM.. 0085 Press F11 to load default values and continue 0085 Press F11 key to enter Boot Menu during POST, as shown by the following figure. Please select boot device： Hitachi HTS545016B9A300 USB: USB Hotplug FDD SATA:4M-CSS HAK40-004G ↑and ↓ to move selection ENTER to select Boot device ESC to boot using defaults 3.2 BIOS SETUP UTILITY Press [Del] key to enter BIOS Setup utility during POST, and then a main menu containing system summary information will appear.
System Time [00:01:09] System Date 03/08/2011] F10 [Tue Save and Exit ESC Exit v02.61 © Copyright 1985-2006 American Megatrends , Inc. 3.3 System Overview BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit System Overview User [ENTER]，[TAB] AMIBIOS or Version [SHIFT-TAB] to Select a field : 08.00.15 Build Date : 03/08/11 ID Use[+] or [-] to : L801V010 configure system Time. Processor Genuine Intel(R) CPU Speed 575 @ 2.
3.4 Advanced Settings BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Advanced Settings Exit Configure CPU WARNING: Setting wrong values In below sections may cause system to malfunction.
Adjacent Cache Line Prefetch Max CPUID Value Limit [Enabled] [Disabled] Execute-Disable Bit Capability [Enabled] Intel(R) C-STATE tech [Disabled] ← Select Screen ↑↓ Select Item +- Charge Field F1 General Help F10 ESC Save and Exit Exit V02.61 © Copyright 1985-2006 American Mega trends , Inc.
► Primary IDE Slaver Detected] : [Not ► Secondary IDE Master : [Not Detected] ► Secondary IDE Slaver Detected] : [Not ► Third IDE Master Detected] : [Not ► Fourth IDE Master Disk] : [Hard ← Select Screen ↑↓ Select Item +- Charge Field F1 General Help F10 ESC Hard Disk Write Protect [Disabled] IDE Detect Time Out (Sec) [35] ATA(PI) 80Pin Cable Detection Device] Save and Exit Exit [Host & V02.61 © Copyright 1985-2006 American Mega trends , Inc.
ATA(PI) 80Pin Cable Detection: [Host & Device] [Host] [Device] 3.4.3 Super IO Configuration BIOS SETUP UTILITY Advanced Configure Win627UHG Super IO Chipset Allow BIOS to Select Serial Port1 Address [3F8] Serial Port Base Serial Port2 Address [2F8] Address.
3.4.4 Hardware Health Configuration BIOS SETUP UTILITY Advanced Hardware Health Configuration System Temperature :36℃/96℉ 55℃/131℉ CPU Temperature :45℃/113℉ 60℃/140℉ CPUFAN Speed :5018 RPM 65℃/149℉ 70℃/158℉ Vcore :1.064V AVCC :5.091 V 5VCC :5.100 V 3.3V :3.328 V 5.0V :5.01 V 12V :12.01 V VSB :5.10 V VBAT :3.
[60%] [50%] [70%] [80%] 3.4.5 ACPI Configuration ACPI Setting: [Advanced ACPI Configuration] ACPI Version Features: [ACPI V1.0] [ACPI V2.0] [ACPI V3.0] ACPI APIC support: [Enabled] [Disabled] AMI OEMB table: [Enabled] [Disabled] Headless mode: [Disabled] [Enabled] [Chipset ACPI Configuration]: APIC ACPI SCI IRQ: [Disabled] [Enabled] High Performance Event Timer: [Disabled] [Enabled] 3.4.
► AHCI Port0 : [Not Detected] ► AHCI Port1 : [Not Detected] ► AHCI Port2 : [Not Detected] ► AHCI Port3 ► AHCI Port4 ► AHCI Port5 : [Not Detected] : [Not Detected] : [Not Detected] ← Select Screen ↑↓ Select Item Enter Go to sub screen F1 General Help F10 Save and Exit ESC Exit V02.61 © Copyright 1985-2006 American Mega trends , Inc. While entering setup, BIOS auto detects the presence of IDE devices. This displays the status of auto detecting of IDE devices 3.4.
3.4.8 PCI Express Configuration BIOS SETUP UTILITY Advanced PCI Express Configuration Active [Disabled] State Power Enables/Disables -Management PCI Express L0s and L1 Link Power States. ← Select Screen ↑↓ Select Item +- Charge Field F1 General Help F10 Save and Exit ESC Exit V02.61 © Copyright 1985-2006 American Mega trends , Inc. Active State Power Management: [Disabled] [Enabled] 3.4.
Smbios Smi Support: [Enabled] [Disabled] 3.4.10 USB Configuration BIOS SETUP UTILITY Advanced USB Configuration Enables support for Module Version – 2.24.3-13.4 legacy USB.ATUO option disables legacy support if no USB USB Devices Enabled : devices are connected 1Keyboard Legacy USB Support USB2.0 Controller Mode BIOS EHCI Hand-Off [Enabled] [Fullspeed] [Enabled] ← Select Screen ↑↓ Select Item +- Charge Field F1 General Help F10 Save and Exit ESC Exit V02.
3.5 Advanced PCI/PnP Settings This part describes configurations to be made on PCI bus system. PCI, namely Personal Computer Interconnect, is a computer bus that allows I/O device to operate nearly as fast as CPU in its own way. Some technical terms will be mentioned here. We recommend that non-professional users not make changes from factory default settings.
[Yes] Plug & Play OS: [No] [Yes] PCI Latency Timer: [64] [32] [96] [128] [160] [192] [224] [248] Allocate IRQ to PCI VGA: [Yes] [No] Palette Snooping: [Disabled] [Enabled] PCI IDE BusMaster: [Disabled] [Enabled] OffBoard PCI/ISA IDE Card: Some PCI IDE cards may require this to be set to the PCI slot number that is holding the card. Auto:Works for most PCI IDE Cards.
[Reserved] Available: Specified IRQ is available to be used by PCI/PnP devices. Reserved: Specified IRQ is reserved for use by legacy ISA devices. DMA Channel 0/1/3/5/6/7: [Available] [Reserved] Available: Specified DMA is available to be used by PCI/PnP devices. Reserved: Specified DMA is reserved for use by legacy ISA devices. Reserved Memory Size: Size of memory block to reserve for legacy ISA devices. [Disabled] [16k] [32k] [64k] 3.
Boot Setting Configuration： Configure Settings during System Boot. Quick Boot: [Enabled] [Disabled] Allows BIOS to skip certain tests while booting .This will decrease the time needed to boot the system. Quiet Boot: [Disabled] [Enabled] Disabled: Displays normal POST messages. Enabled: Displays OEM logo instead of POST messages. AddOn ROM Display Mode: Set display mode for Option ROM. [Force BIOS] [Keep Current] Bootup Num－Lock: Select Power-on state for Numlock.
Enabled: Allows option ROMs to trap interrupt 19. [Disabled] [Enabled] Boot Device Priority: Specifies the Boot Device Priority sequence. Hard Disk Devices : Specifies the Boot Device Priority sequence from available Hard Drives. 3.7 Security Settings BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Security Settings Supervisor Password Chipset Exit Install or Change the :Not Installed User Password password.
[Always] Setup: Check password while invoking setup. Always: Check password while invoking setup a well as on each boot. Boot Sector Virus Protection: [Disabled] [Enabled] Enabled / Disabled Boot Sector Virus Protection. Type the password with up to 6 characters and then press Enter key. This will clear all previously typed CMOS passwords. You will be requested to confirm the password. Type the password again and press Enter key. You may press Esc key to abandon password entry operation.
← Select Screen ↑↓ Select Item Enter Go to sub screen F1 General Help F10 Save and Exit ESC Exit V02.61 © Copyright 1985-2006 American Mega trends , Inc. Note: Due to limited address length of BIOS, only a portion of panel parameters are listed in BIOS Setup. If the connected panel is not included in the parameter list, display problem will occur. In this case, Please do not change BIOS setup. 3.8.
Memory Remap Feature: [Enabled] [Disabled] Memory Hole: [Disabled] [15MB-16MB] Initate Graphic Adapter: Select which graphics controller to use as the primary boot device.
Backlight Control Mode Backlight [VBIOS-Default] Image [DC] Adaptation F1 F10 ESC General Help Save and Exit Exit V02.61 © Copyright 1985-2006 American Mega trends , Inc.
Backlight Control Control: [Level5] [Level0] [Level1] [Level2] [Level3] [Level4] [Level6] [Level7] Note: Panel support PWM Function. Backlight Control Mode: [DC] [PWM] Backlight Image Adaptation: [VBIOS-Default] [BIA Disabled] [BIA Enabled at Level1] [BIA Enabled at Level2] [BIA Enabled at Level3] [BIA Enabled at Level4] [BIA Enabled at Level5] 3.8.2 South Bridge Configuration: BIOS SETUP UTILITY Chipset South Bridge Chipset Configuration USB Functions Ports] USB2.
PCIE Port 0 PCIE Port 1 [Auto] [Auto] +- Charge Field F1 General Help PCIE Port 2 [Auto] F10 PCIE Port 3 PCIE Port 4 PCIE High Priority Port [Auto] [Auto] [Disabled] ESC Save and Exit Exit V02.61 © Copyright 1985-2006 American Mega trends , Inc. USB Functions: [8 USB Ports] [Disabled]， [2 USB Ports] [4 USB Ports] [6 USB Ports] USB 2.
Restore on AC Power Loss: [Power Off] [Power On] [Last Status] PCIE Ports Configuration: PCIE Port 0: [Auto] [Enabled] [Disabled] PCIE Port 1: [Auto] [Enabled] [Disabled] PCIE Port 2: [Auto] [Enabled] [Disabled] PCIE Port 3: [Auto] [Enabled] [Disabled] PCIE Port 4: [Auto] [Enabled] [Disabled] PCIE High priority Port: [Disabled] [Port 0~Port5] PCIE Port 0 IOxAPIC Enabled: [Disabled] [Enabled] PCIE Port 1 IOxAPIC Enabled: [Disabled] [Enabled] AHM-6159P User Manual 46
PCIE Port 2 IOxAPIC Enabled: [Disabled] [Enabled] PCIE Port3 IOxAPIC Enabled: [Disabled] [Enabled] PCIE Port4 IOxAPIC Enabled: [Disabled] [Enabled] PCIE Port5 IOxAPIC Enabled: [Disabled] [Enabled] 3.
Save configuration changes and exit setup? (F10 key can be used for this operation) [OK] [Cancel] Discard Changes and Exit: Discard Changes and Exit setup? (ESC key can be used for this operation) [OK] [Cancel] Discard Changes: Discard changes? (F7 key can be used for this operation) [OK] [Cancel] Load Optimized Defaults: Load Optimized Defaults? (F9 key can be used for this operation) [OK] [Cancel] Load Fail-Safe Defaults: Load Fail-Safe Defaults? (F9 key can be used for this operation) [OK] [Cancel] AHM-
Chapter 4 Installation of Drivers This chapter describes the installation procedures for software and drivers under the windows XP. The software and drivers are included with the motherboard. The content includes Intel(R) Chipset GM/GL45 and ICH9M, Intel(R) VGA GM/GL45 Chipset, INTEL82574L Ethernet Driver, Realtek ALC 662 Audio Driver and Touch Panel Driver. Installation instructions are given below.
4.1 Intel Chipset Driver To install the Intel chipset driver, please follow the steps below. Step 1. Access Drivers list as shown below. list. Select Intel(R) Chipset GM/GL45 and ICH9M from the Step 2. Click Next to set up program.
Step 3. Click Yes to accept all of the terms of the license agreement. Step 4. Click Next to continue.
Step 5. Click Next. Step 6. Select Yes, I want to restart this computer now. to restart the computer. then remove any installation media from the drives.
4.2 Intel(R) VGA GM/GL45 Chipset To install the VGA drivers, follow the steps below to proceed with the installation. Step 1. Select Intel(R) VGA GM/GL45 Chipset. Step 2. Click Next to continue the set up program.
Step 3. Click Next. Step 4. Click Yes to accept all of the terms of the license agreement.
Step 5. Click Next to continue the installation. Step 6. Click Next.
Step 7. Select No, I will restart this computer later., and click Finish to complete the installation. 4.3 Intel 82574L Ethernet Driver To install the Intel 82574L Ethernet Driver, please follow the steps below. Step 1.
Step 2. Click Next to continue the installation. Step 3. Select I accept the terms in the license agreement and click Next.
Step 4. Tick Drivers, Intel(R) PROSet for Windows* Device Manager and Advanced Network Services. Click Next to continue the installation. Step 5. Click Install to begin the installation.
Step 6. Click Finish to complete the installation. 4.4 Realtek ALC662 HD Audio Driver Installation To install Realtek ALC662 Audio Driver, please follow the steps below. Step 1. Select Realtek ALC662 Audio Driver from the list.
Step 2. Click Next to continue the installation. Step 3. Click Yes, I want to restart my computer now. to restart the computer. Click Finish.
Chapter 5 Touch Screen Installation This chapter describes how to install drivers and other software that will allow your Controller Board to work with different operating systems. 5.1 Introduction to Touch Screen Controller Board 15” projected capacitive touch panel control board is a touch screen control board designed for USB interface and specific for touch screens. It is designed with USB interface features with multiple devices supporting function.
5.2.1 Installing Software If you have an older version of the driver installed in your system, please remove it first. Follow the steps below to install the driver. Please make sure your USB controller device had plugged in advance. When the system first detects the controller board, a screen appears that shows “Unknown Device”. Do not use this hardware wizard. Press Cancel. Insert the product CD install setup.exe. the screen below would appear. Click touch panel driver.
Step 1. Click Next to install eGalaxTouch on your computer. Step 2. Tick Install RS232 interface driver then click Next.
Step 3. Select None, then click Next. Step 4. There is a pop-up, click OK. Step 5. Tick Support Muti-Monitor System and click Next.
Step 6. Click Browse to create new folder. Click Next to continue settings. Step 7. Under eGalax Touch folder, select Accessories. AHM-6159P User Manual Click Next to continue.
Step 8. Select Create a eGalaxTouch Utility shortcut on desktop. Click Next. Step 9. eGalaxTouch is configuring your new software installation.
Step 10. Click Yes to do 4 point calibration. 5.2.2 Software Functions General In this window, you can see there is USB Controller. Click OK to continue.
Setting Beep Beep On Touch Beep On Release Beep From System Beep Beep From Sound Card Linearization Style 9 points 25 points Double Click Time Shorter Longer Double Click Area Smaller Bigger Normal mode Simulate the mouse mode AHM-6159P User Manual 68
Option Function Enable Constant Touch Enable Auto Right Click Enable Touch Enable Cursor Stabilization Constant Touch Area Auto Right Click Time AHM-6159P User Manual 69
Tools Click OK to continue the settings. 4 Points Calibration Do 4 points alignment to match display. Clear and Calibrate Clear linearization parameter and do 4 points alignment. Linearization Do 9 points linearization for better touchscreen linearity. Draw Test Do draw test to verify the touch accuracy.
Display In this window, it shows the mode of display. Enable Multiple Monitors.
Other Other mode of display. Quarter1~4 and Customized area. Active Area Drag active area to enable Active Area Function.
Hardware Saturn Hardware Configuration AHM-6159P User Manual 73
About To display information about eGalaxTouch and its version.
