Thank you for choosing the GlucoSure Link Blood Glucose Monitoring System to help you easily monitoring your blood glucose. We hope it will be of great help in the management of your diabetes. This manual explains how to use your new meter. Before testing, carefully read though this manual and the package inserts the come with: GlucoSure Link blood glucose test strip, Contrex Plus III glucose control solution. Pay particular attention to listed warnings and cautions.
GlucoSure Link Blood Glucose Monitoring System 2 Intended Use The GlucoSure Link Blood Glucose Monitoring System is intended for the quantitative measurement of glucose in fresh capillary whole blood samples drawn from the fingertips, forearm, or palm.
• The meter and lancing device are for single patient use. Do not share them with anyone including other family members! Do not use on multiple patients! • All parts of the kit are considered biohazardous and can potentially transmit infectious diseases, even after you have performed cleaning and disinfection. • Users should wash hands thoroughly with soap and water after handling the meter, lancing device, or test strips.
GlucoSure Link Blood Glucose Monitoring System 4 Limitations • Inaccurate results may occur in ▪ Severely hypotensive individuals ▪ Patients in shock ▪ In a hyperglycemic-hyperosmolar state with or without ketosis • Do not use on critically ill patients. • Do not use on neonates • Do not use the system above 6,562 feet (2,000 meters) in altitude. • Do not use if hematocrit exceeds the acceptable range between 30% to 55% when testing blood glucose.
Understanding Your New Blood Glucose Kit The GlucoSure Link Meter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 The GlucoSure Link Meter Display Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 The GlucoSure Link Blood Glucose Test Strip . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Contrex Plus III Glucose Control Solution (Required). . . . . . . . . . . . . . . . . . . . . 13 Setting Up Your New System The Setup Screen. . . . . . . . .
GlucoSure Link Blood Glucose Monitoring System 6 Understanding Your Blood Glucose Test Results. . . . . . . . . . . . . . . . . . . . . . . 41 Viewing Your Meter’s Memory Viewing Stored Reading and 7, 14, 30 Days Average from Memory . . . . . . . . . 43 Data Transmission Upload Data via Bluetooth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Caring for the Meter Changing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The GlucoSure Link Blood Glucose Monitoring System comes in either as a kit or simple package.
GlucoSure Link Blood Glucose Monitoring System 8 The GlucoSure Link Blood Glucose Meter Test Strip Port This is where you insert the test strip and the meter will turn on automatically. Meter Display Shows your blood glucose test results, memory values, averages, and other messages.
GlucoSure Link Blood Glucose Monitoring System Battery Holder Holds two AAA batteries 9
GlucoSure Link Blood Glucose Monitoring System The GlucoSure Link Meter Display Screen BEEPER BATTERY TEMPERATURE BLE icon CLOCK MEMORY ALARM BLOOD DROP and ARROW TEST STRIP UNIT CTL HOUR/MINUTES MONTH DAY DATE/DAY AVG 10
TEMPERATURE ��������������Appears when it is either too hot or too cold to test (outside the ranges of 50 ̊F~104 ̊F). BLOOD DROP and ARROW ����������������������������������������Indicate the meter is ready for testing (see page 36). GlucoSure Link Blood Glucose Monitoring System BLE ����������������������������������Indicate Bluetooth is turn on MEMORY ������������������������Indicates the number in the meter display is a stored test value (see page 43).
GlucoSure Link Blood Glucose Monitoring System 12 The GlucoSure Link Blood Glucose Test Strip Contact Points Insert this end to the test strip port on the meter Sampling End Apply blood or control solution here The GlucoSure Link Blood Glucose Test Strips are glucose specific, biosensorbased test strips that require very little blood sample to quickly test glucose in fresh capillary whole blood.
Call your local supplier or pharmacy to order control solution. If they do not stock it, please contact us at 1-877-979-5454 between 8:00 am and 5:00 pm EST, Monday through Friday. It is the standard glucose concentration solution required to perform a Glucose Control Solution Test (See Control Solution Testing). It is available at 3 levels.
GlucoSure Link Blood Glucose Monitoring System 14 Setting Up Your New System The Setup Screen The Setup Screen of the GlucoSure Link Blood Glucose Meter lets you take advantage of the advance functions of this meter. Simply use ▲▼ buttons to navigate to the desired function icon, and press the Enter ( ) button to enter the function when the icon is flashing. Navigate to End at the display screen to exit the Setup Screen.
mem ������������������������ Press Enter ( ) to enter Memory to retrieve stored results. Your meter can memorize up to 300 memories with date and time. (see page 43). ��������������������������� Press Enter ( ) to enter Clock Setup (see page 16). ���������������������������� Press Enter ( ) to enter Alarm Setup (see page 19). Your meter can set up to 3 alarms. ��������������������������� Press Enter ( ) to enter Beeper Setup (see page 22).
GlucoSure Link Blood Glucose Monitoring System Setting the Clock You will need: • Your GlucoSure Link Blood Glucose Meter NOTE: • If you do not set the date and time on GlucoSure Link Blood Glucose Meter, the test or control results will not be stored in the meter’s memory. Step 1. Press and hold Enter ( ) to turn on the meter. Step 2. Press Enter ( ) to go into setup screen, then press ▲or▼ until start to flash. Press Enter ( ) to enter clock setup. Step 3 - Set the Year The current year will flash.
Step 5 - Set the Date The current date will flash. Press ▲ or ▼ to select the correct date. Press Enter ( ) to confirm your choice and proceed to set time format. Step 6 - Set 12-hour or 24-hour Time Format The current time format will flash. Press ▲ or ▼ to select for either 12-hours format or 24- hour format. Press Enter ( ) to confirm your choice and proceed to set hour. GlucoSure Link Blood Glucose Monitoring System Step 4 - Set the Month The current month will flash.
GlucoSure Link Blood Glucose Monitoring System 18 Step 8 - Set Minute The current minutes will flash. Press ▲ or ▼ to select the correct minutes. Press Enter ( ) to confirm your choice and finish setting the clock. NOTE: • Anytime during setup, you can insert a GlucoSure Link Test Strip to begin testing. Any changes made so far will be stored. • You may need to reset time after changing batteries.
You can set up to three alarms on the GlucoSure Link Blood Glucose Meter. You must set the clock before you can set the alarms. When an alarm sounds, the meter will turn on, and a melody will sound for 30 seconds. Pressing Enter ( ) or inserting a test strip will silence the alarm. You can set up one or all three alarms. You will need: • Your GlucoSure Link Blood Glucose Meter Step 1. Press and hold Enter ( ) to turn on the meter. Step 2. Press Enter ( ) to enter setup screen. Step 3.
GlucoSure Link Blood Glucose Monitoring System 20 Step 4. The display screen will indicate alarm 1 status (the default is OFF). You can turn it on or off by pressing ▲ or ▼. Step 5. Press Enter ( ) and the hour will flash. Press ▲ or ▼ to select the hour. Press Enter ( ) to confirm your choice and proceed to set minutes. Step 6. The current minutes will flash. Press ▲ or ▼ to select the correct minutes. Press Enter ( ) to confirm your choice and proceed to set alarm 2. Step 7.
• Alarm will not sound during testing. • Alarm will follow the time format (12-hour or 24-hour) you choose when setting up the clock. • Alarm settings will not be erased when changing batteries. Begin testing by inserting a GlucoSure Link Blood Glucose Test Strip (see Testing Your Blood Glucose on page 32 or Control Solution Testing on page 24), or press and hold Enter ( ) to turn off the meter, or see the next section on how to set up the beeper on your meter.
GlucoSure Link Blood Glucose Monitoring System Setting Beeper Function The default setting for the beeper function is on, and can be switched off to conserve battery power. You will need: • Your GlucoSure Link Blood Glucose Meter Step 1. Press and hold Enter ( ) to turn on the meter. Step 2. Press Enter ( ) to go into setup screen. Press ▲or▼ until Enter ( ) to enter beeper setting. start to flash. Press Step 3.
• Anytime during set up, you can insert a GlucoSure Link Blood Glucose Test Strip and begin testing. Any changes made so far will be stored. • Beeper setting will not be erased when changing batteries. Begin testing by inserting a GlucoSure Link Blood Glucose Test Strip (see Testing Your Blood Glucose on page 32 or Control Solution Testing on page 24) or press and hold Enter ( ) to turn off the meter.
GlucoSure Link Blood Glucose Monitoring System 24 Control Solution Testing Performing a Control Solution Test The purpose of the control solution testing is to make sure the GlucoSure Link Blood Glucose Meter and the GlucoSure Link Blood Glucose Test Strip are working properly.
You will need: • Contrex™ Plus III Control Solution (Low, L1 and L2) • Your GlucoSure Link Blood Glucose Meter • A new GlucoSure Link Blood Glucose Test Strip Step 1. Take out a GlucoSure Link Blood Glucose Test Strip from the test strip bottle and close the bottle immediately. Insert the test strip to turn on the meter. GlucoSure Link Blood Glucose Monitoring System unused control solution 3 months after opening. • DO NOT FREEZE. Store the control solutions at 59°F to 86°F.
GlucoSure Link Blood Glucose Monitoring System 26 • Keep away from direct sunlight and heat. Store the test strip bottle in a dry, cool place. • Record the "date opened" on the bottle label. Discard the bottle and any remaining test strip after 3 months from date of opening. • Test under the temperature range of 50°F to 104°F, relative humidity 20 to 85%RH. Your meter will not work outside these ranges. • Must insert test strip into the test strip port. .
GlucoSure Link Blood Glucose Monitoring System Step 4. Squeeze a drop of control solution onto a clean, dry, nonabsorbent surface. Do not apply control solution to the test strip directly from the bottle. Replace the bottle cap on the control solution bottle immediately after use. Step 5. Gently touch the drop of the control solution to the tip of the test strip. The meter will beep indicating it has received the control solutio Step 6. The screen will start to count down.
GlucoSure Link Blood Glucose Monitoring System 28 NOTE: • Control solution testing results will be stored into the meter memory and indicated by ctl icon. • Control solution testing result will not be used for calculating averages. Step 8. Remove the used test strip. The meter will automatically turn off. Discard the used test strip into proper wastebasket. IMPORTANT: • Do not reuse Test Strips.
If your control solution testing is out of range (too high or too low), it may be caused by the following: Possible Causes What you can do … • Wrong brand of Control Solution being used • Make sure you are using Contrex™ Plus III Control Solution. • Control solution is not at proper storage condition 59°F to 86°F • Make sure the testing environment is between 50°F to 104°F, 20~85% RH.
GlucoSure Link Blood Glucose Monitoring System 30 Testing Your Blood Glucose You will need: • Your GlucoSure Link Blood Glucose Meter • A new GlucoSure Link Blood Glucose Test Strip • Lancing device with a clean, unused lancet (or safety lancets) • Clear cap for Alternate Site Testing (AST) on palm and forearm Before you begin, make sure: • To set up your meter properly and run a control test. See Setting Up Your New System and Control Solution Testing for details.
• Check the expiration date on the test strip bottle. DO NOT use expired Test Strips. • When you open a bottle of Test Strips for the first time, record the“open date” on the test strip bottle. Discard the bottle and any remaining Test Strips 3 months after the open date. • After taking a Test Strip out of the bottle, close the cap of the bottle immediately. • Use each Test Strip immediately after taking it out from the bottle. • Do not use wet, bent, scratched, or visibly damaged Test Strips.
GlucoSure Link Blood Glucose Monitoring System Preparing Your Lancing Device CAUTION: • The lancets are for single use only. Always use a new, sterile lancet each time you perform the test. • DO NOT share your lancing device or lancets with other people. Sharing or reusing lancets can lead to disease transmission. • Please follow your local healthcare provider’s recommendation regarding proper disposal of used lancets. • When performing a blood glucose test, use a new sterile lancet every time.
TIP: • To avoid soreness, select a site on the side of your fingertips. To avoid calluses, choose a different site each time for obtaining the blood sample. GlucoSure Link Blood Glucose Monitoring System Step 3. Hold the lancing device (puncture) or lancet against the side of the finger and lance the finger. Follow manufacturer’s instruction for how the lancing device (puncture) or lancet should be used.
GlucoSure Link Blood Glucose Monitoring System Important Information on Alternative Site Testing (AST) The GlucoSure Link Blood Glucose Monitoring System can test for blood glucose from areas other than your fingertip such as palm and forearm (alternative site testing, or AST).
Consult with your healthcare professional to decide if AST is right for you. NOTE: • Rubbing forearm until warm before lancing will help minimize the difference with fingertip test results. The palm (at the base of the thumb) does not require rubbing before testing. • If results from alternate site testing do not agree with how you feel, use fingertip testing instead.
GlucoSure Link Blood Glucose Monitoring System 36 Performing a Blood Glucose Test Step 1. Take out a GlucoSure Link Blood Glucose Test Strip from the test strip bottle and close the bottle immediately. Insert the test strip into the test strip port to turn on the meter. IMPORTANT: • Check the expiration date printed on the test strip bottle and its package. Do not use expired test strips. • Use each test strip immediately after removing it from the bottle. • Do not use wet or damaged test strips.
3 4 5 Step 3- obtain blood sample For Fingertip Testing: Hold the lancing device (use the blue adjustable cap) against the side of your fingertip and press the release button to create a puncture. TIP: GlucoSure Link Blood Glucose Monitoring System Step 2. Wait for a flashing blood drop and an arrow icon appears on the meter display screen. • Gently message your hand and finger toward the puncture site to form a drop of blood (approximately: ). Do not “milk” or squeeze around the puncture site.
GlucoSure Link Blood Glucose Monitoring System 38 For Testing on Palm and Forearm: Hold the lancing device (use the clear adjustable cap) against the test site (base of palm or forearm). Avoid a test site that has veins, moles, excessive hair, or bone. Press the lancing device firmly against the test site and press the release button, do not lift up. For forearm test sites, apply and release pressure (“pumping”) for a few seconds while keeping the lancing device in constant contact with the skin.
Step 5. The screen will start to count down. After 6 seconds, your glucose testing result will appear on the meter display screen. Your test result will be automatically stored into the meter memory. CAUTION: • If you see “HI” or “LO” displayed, your blood glucose level may be above 600 mg/ dL (33.3 mmol/L) or below 20 mg/dL (1.1 mmol/L). Test again using fingertip testing, DO NOT test on forearm or palm. If you still receive the same result, call your physician or healthcare professional immediately.
GlucoSure Link Blood Glucose Monitoring System 40 sample taken from a fingertip (do not use an alternative site). If the test result still does not match how you feel, contact your doctor or healthcare professional. • Do not ignore test results. Do not alter your blood glucose management or treatment without first consulting your doctor or healthcare professional. Step 6. Remove the used test strip into proper wastebasket. The meter will automatically shut off. Step 7.
Blood glucose value will vary depending on food intake, medication, health, stress, and exercise. The ideal ranges for adults without diabetes are(2): • less than 100 mg/dL before meals. • less than 140 mg/dL after meals. It is important to consult with your physician or healthcare professional to determine an appropriate target range for you.
GlucoSure Link Blood Glucose Monitoring System 42 IMPORTANT: • Inaccurate results may occur in severely hypotensive individuals or patients in shock. • Inaccurate low results may occur for individuals experiencing a hyperglycemichyperosmolar state, with or without ketosis. • Critically ill patients should not be tested with blood glucose meters. 2. American Diabetes Association, Standard of Medical Care in Diabetes 2020, Vol. 43 (Suppl.
Your GlucoSure Link Blood Glucose Meter automatically stores up to 300 test and control results with date and time. The meter also provides 7, 14, and 30 days averaging to help track your blood glucose trend. You must set up the date and time on your meter before using the memory and day averaging function, see Setting Up Your New System on page 14. The meter will not memorize test or control results if the date and time are not set.
GlucoSure Link Blood Glucose Monitoring System 44 mem will appear at the upper left corner of the display screen together with your most recent testing result. Press ▲ to see the next result, and the next, and so on. Holding ▲ will flash through the results. nil will appear on the display screen after the last recorded test result if less than 300 readings are stored. You can press ▼ to go back viewing from the oldest to the most recent readings. Step 4.
• Control testing results is flagged by ctl on the bottom left corner of the display screen in addition to mem. • When the meter memory is blank, the display screen will show nil. • When there are no day average data available, the display screen will show 4 dashes. • If the meter memory is full, adding a new test result will cause the oldest one to be deleted. • Memorized test results and day averages will not be erased when changing batteries. • You can begin testing anytime by inserting a test strip.
GlucoSure Link Blood Glucose Monitoring System Data Transmission Test results stored in the GlucoSure Link Blood Glucose Meter’s memory can be transmitted to your personal computer or mobile devices. Upload Data via Bluetooth The process of connecting between the meter and the mobile device is called pairing. You will need an application on your mobile device that can accept the meter’s data.
Step 3 Press Enter ( ) to pair with your Mobile Device. Step 4 The BLE icon stops flashing as pairing is completed. Then the screen of meter will show “On” and “BLE” icon ( ). As pairing fails, Err6 is displayed on the screen of the meter, please refer to “Solving Problem” for more details. BLE Transmission Step 5 Press Enter ( ) to confirm Data transmission. Meter shall start sending data to mobile device. When Err7 is displayed on the screen of the meter, refer to “Solving Problem” for more details.
GlucoSure Link Blood Glucose Monitoring System NOTE: • You need to install an app that accepts meter data on your mobile device. • As long as the mobile device has an application that can accept meter data, the meter does not need to be paired. • When the meter is in transfer mode, testing is not possible. • If changing different mobile device, the pairing procedure must be performed.
GlucoSure Link Blood Glucose Monitoring System Quality of service for the wireless connectivity for data downloading • Acceptable latency: 4 seconds • Max throughput: low speed; 21 kbps • Acceptable level of probability for loss of information within the network: probability is 0% • Accessibility/ signal priorities of the network: only Bluetooth is available • Data integrity: check sum function for transmitting and receiving packets.
GlucoSure Link Blood Glucose Monitoring System 50 Caring for the Meter Caring for your GlucoSure Link Meter is easy. Follow these simple guidelines to keep your meter working properly. NOTE: • DO NOT get water inside the GlucoSure Link Blood Glucose Meter. Never immerse the meter or hold it under running water. • DO NOT use glass cleaners or household cleaners on the meter. • DO NOT contaminate the strip holder with blood or control solution. • DO NOT take the GlucoSure Link Blood Glucose Meter apart.
Batteries need to be changed when the meter display. icon appears on the Materials you will need: • Two Alkaline AAA Batteries • Your GlucoSure Link Blood Glucose Meter Step 1. Turn meter off. Press firmly on the battery cover and slide in the direction of the arrow. Remove the old batteries. Step 2. Insert new batteries NOTE: . Slide the battery cover back into the meter firmly. • If the batteries are inserted upside down, the meter will not operate.
GlucoSure Link Blood Glucose Monitoring System 52 • Dispose of old batteries according to local environmental regulations. • To obtain accurate test results: Improper use may cause explosion or leakage of flammable liquid. Do not expose the batteries to extremely high temperatures or extremely low air pressure. • Batteries might leak chemicals if unused for a long time. Remove the batteries if you are not going to use the device for an extended period. • Keep batteries out of reach of small children.
Cleaning and disinfection are different and both should be performed. Cleaning, such as removing dirt with a damp paper towel, is part of your normal care and maintenance, but cleaning does not kill germs effectively. After use and exposure to blood, all parts of this kit can potentially transmit infectious diseases. Disinfection is the only way to reduce your exposure to disease. For cleaning and disinfecting information see pages 53–56 in this manual.
GlucoSure Link Blood Glucose Monitoring System 54 Cleaning and disinfection frequency: The GlucoSure Link Blood Glucose meter and lancing device should be cleaned when it appears dirty or contaminated with blood. It should be disinfected every day according to the validated cycle of 1825 times. The validated cycle of 365x5=1825 times is equivalent to one cleaning plus one disinfection per day over 5 years.
6. Wash hands with soap and water. NOTE: • If the meter or lancing device is being operated by a second person who is providing testing assistance to the user, the meter or lancing device should be cleaned and disinfected prior to use by the second person. Avoid alcohol and ammonia. Even though these two ingredients are excellent disinfectants, they are not safe for your meter or lancet device. Alcohol damages the LED read out and ammonia corrodes the metal parts.
GlucoSure Link Blood Glucose Monitoring System 56 • User should wash hands thoroughly with soap and water after handling the meter, lancing device, and test strip. • Keep DISPATCH out of reach of children. • Do not flush towels down toilet. • Do not get water inside the meter or hold it under running water. • Do not use glass or household cleaners on the meter. • Avoid wetting the test strip holder.
Dispatch is the product of Caltech, the catalog number is 69150 (150 count) To find a local distributor in your area call Customer Service at 800.234.7700, MonFri 8:30am - 5:00pm EST You can also purchase the Dispatch on the web site below: https://www.cloroxpro.com/products/dispatch/ http://www.amazon.com If you need assistance or have questions about cleaning and disinfection for the meter, please contact customer service at 1-877-979-5454 between 8:00 am and 5:00 pm EST, Monday through Friday.
GlucoSure Link Blood Glucose Monitoring System 58 Storage and Precautions • The Meter and the Test Strips are designed to be used within a temperature range of 50°F - 104°F and relative humidity between 20% - 85%. • Avoid leaving the Meter in extremely hot or cold places, such as near a heat source or in an extremely hot or cold car. • Do not store or use the Meter or Test Strips where they may be exposed to high humidity levels, such as in a bathroom or kitchen.
This section details the significant display screen messages and error codes you will encounter when using your GlucoSure Link Blood Glucose meter and GlucoSure Link Blood Glucose test strips. Message What it means What you should do The meter electronics or test strip is damaged • Remove the battery and turn on the Meter again. • Remove the test strip and insert a new test strip again.
GlucoSure Link Blood Glucose Monitoring System 60 Message What it means What you should do Not enough sample on the test strip to start • Remove the Test Strip and repeat the test with a new test strip. See Testing Your Blood Glucose on page 32. Meter fails in BLE status check • Replace the batteries and turn on the meter again. • If problem persists, call us at 1-877-9795454 Monday through Friday from 8am to 5pm EST. BLE pairing failure” • Check Bluetooth device is working well and repeat pairing.
What it means Data transmission via BLE is fail. What you should do • Remove strip from the test strip port. BLE disconnection • Check Bluetooth device is working well and between meter and repeat pairing and data transmission. mobile device happens during transmission procedure. Batteries are low • Change the battery according to page 51, Changing the Battery.
GlucoSure Link Blood Glucose Monitoring System 62 Message What it means What you should do Temperature out of range • Move the meter into an area that is within 50 ̊F~104 ̊F, and allow 10 to 15 minutes for it to reach the new temperature. Test result is higher than 600 mg/dL • Wash and dry your hands and repeat the test on your fingertip with a new test strip. If the result is still “HI,” contact your physician or healthcare professional immediately.
What it means There are no memorized results in the meter What you should do • Check if the date and time on you meter is set up. See Setting Up Your New System on page 16. • Start testing your blood glucose, see Testing Your Blood Glucose on page 32.
GlucoSure Link Blood Glucose Monitoring System 64 Product Warranty Apex Biotechnology Corporation warrants the GlucoSure Link Blood Glucose Meter to be free of defects in workmanship and materials under normal use for a period of five (5) years from the date of purchase to the consumer. The liability of Apex Biotechnology Corporation is limited to repair or replacement and in no event shall Apex Biotechnology Corporation be liable for any collateral or consequential damages or loss.
Test Strips: Test Range: Calibration: Test Time: Sample Size: Hematocrit Range: Display Type: Memory: Result Averaging: Dimensions: Weight: Battery: Battery Life: Automatic Power-off: Operating Temperature: Operating Relative Humidity: Storage Condition: GlucoSure Link Blood Glucose Test Strip 20~600 mg/dL (1.1~33.3 mmol/L) Plasma 6 Seconds ≥ 0.8 μL 30~55% Large LCD screen 300 blood test results with date and time 7, 14, and 30 days averaging 93L x 58W x 20.5H (mm) not more than 79 g with batteries Two 1.
GlucoSure Link Blood Glucose Monitoring System 66 Suggested Representation of Accuracy for Home Use by Lay-Users The GlucoSure Link Blood Glucose Meter result may vary slightly from your actual blood glucose value. This may be due to slight differences in technique and the natural variation in the test technology. The chart below shows the results of a study where 350 typical users used the GlucoSure Link Blood Glucose Meter to test their blood glucose level. The following accuracy results were obtained.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
GlucoSure Link Blood Glucose Monitoring System 68 CAUTION: • Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. • This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
