User's Manual
Table Of Contents
- Scope of This Manual
- Conventions Used in This Manual
- Intended Audience for this Manual
- General Cautions and Warnings
- What is new?
- Overview Of Base Station
- 1.1 Conceptual Overview of the PacketMax System
- 1.1.1 Cell Size, Capacity, and Scalability
- 1.1.2 Frequency Bands
- 1.1.3 PacketMax Network Connectivity
- 1.2 Bridge Mode and VLAN Mode of Base Station
- 1.2.1 Bridge Mode
- 1.2.2 VLAN Mode
- 1.2.3 Point-to-Point Mode
- 1.3 Features of PacketMax System
- 1.3.1 The PacketMax System’s IP Network
- 1.3.2 Services
- 1.3.3 MIBs
- 1.3.4 Service Offerings and QoS
- 1.3.5 ARQ Feature
- 1.3.6 3 DES Encryption
- 1.3.7 Certificates and Management
- 1.3.8 Upgrades
- Base Station Components
- 2.1 PacketMAX Base Station
- 2.2 5-Slot ATCA Chassis
- 2.3 Wireless System Controllers
- 2.3.1 Major Differences Between WSC-S-24 and WSC-48
- 2.3.2 One Port WSC-S-24
- 2.3.3 QUAD Wireless Controller (QWC) Card - WSC-48
- 2.3.4 Compatibility matrix with radio
- 2.4 Main System Controller Card
- 2.5 MSC Redundancy
- 2.5.1 Redundancy support
- 2.6 AC Supply
- 2.7 Power LEDs and ESD connector
- 2.8 Hot Swap
- 2.8.1 WSC-48 Hot Swap
- 2.8.2 WSC-S-24 Hot Swap
- 2.8.3 MSC Hot Swap
- 2.9 Maintaining Proper Chassis Air FLow
- 2.10 Fan Unit
- 2.11 Serial Cable Pinout
- 2.11.1 Serial Connection Instructions
- 2.12 PacketMax 5000 Rear Panel
- 2.12.1 Grounding
- 2.12.2 DC Power Connection
- 2.13 AC Power Connection
- 2.13.1 Fuse
- 2.14 Base Station Radio
- Installing the Base Station IDU
- Installing the Base Station ODU Radio and Antenna
- 4.1 Radio Compatibility
- 4.2 Installing the Antenna
- 4.3 Installing the Base Station Radio ODU
- 4.3.1 3.3 and 3.5 GHz BSR Package Contents
- 4.3.2 5.8 GHz BSR Package Contents
- 4.3.3 Preparing and Mounting the 3.3 and 3.5 GHz BSR
- 4.3.4 Preparing and Mounting the 5.8 GHz BSR
- 4.3.5 Using the BSR with the Antenna and IDU
- Commissioning the Base Station
- 5.1 Summary of Configuration of Base Station
- 5.2 Establishing an Ethernet Connection with Cat-5 Cable
- 5.3 Establishing a Serial Connection to the Base Station
- 5.4 Configuring DHCP
- 5.5 Obtaining the MAC Address of the Base Station
- 5.6 Selecting Management or Data Traffic
- 5.7 Provisioning the Base Station with WaveCenter EMS
- 5.8 Rebooting the Base Station
- 5.9 Verifying Operations
- 5.10 Ensuring Encryption
- 5.11 Upgrading Base Station Manually
- 5.11.1 WSC upgrade
- 5.11.2 MSC Upgrade
- Event Reporting
- Command Line Interface (CLI)
- Cables, Spares and Accessories
- System Specifications
- D.1 Physical interfaces of PM 5000 - 12 sector
- D.2 Physical interfaces of PM 5000 - 4 sector
- D.3 QoS and Networking Parameters
- D.4 Dimensions and Weight
- D.5 Environmental
- D.6 Radio Specifications
- 4.6.1 PM-BSR-33 and PM-BSR-35 Radio Specifications
- 4.6.2 PM-BSR-58 Radio Specifications
- 4.6.3 Antenna Specifications
- D.7 Antenna Types, Maximum Gains and Maximum Output Power Point to Multipoint Operation
- D.8 Transmit Output Power Regulations
- Certifications
- Troubleshooting
3–1
PacketMax 5000 Installation and Operation Manual, 10007678 Rev J
Chapter 3. Installing the Base Station IDU
Installing the Base Station IDU
This chapter outlines the basic procedure for installing a PacketMax 5000 wireless
cell system and putting it into operation. It identifies the minimal requirements for
getting the system up and running.
WARNING: Aperto assumes that installation procedures will be performed by
qualified professionals following all safety and other requirements and
acting in accordance with standard practices and procedures. Failure
to meet safety requirements and/or use of non-standard practices
and procedures could result in personal injury and/or damage to
equipment.
All of the instructions presented in this chapter are discussed in more detail in
subsequent chapters of this manual and in the PacketMax Subscriber Equipment
Installation and Operation manuals.
This chapter contains the following topics:
Planning, Site Preparation, and Installation
Installation Procedure
Synchronizing Multiple BSs at a Site
3